| draft-anshoo-test-spec-m3ua-01Description: Request For CommentsYou can download source copies of the file as follows:
Listed below is the contents of file draft-anshoo-test-spec-m3ua-01.txt.
INTERNET-DRAFT Anshoo Sharma[EDITOR]
Hughes Software Systems
Issued: May 2003
Expires: Nov 2003
Test Specification for MTP3 User Adaptation
<draft-anshoo-test-spec-m3ua-01.txt>
Status of This Memo
This document is an Internet-Draft and is in full conformance with all
provisions of Section 10 of RFC 2026. Internet-Drafts are working
documents of the Internet Engineering Task Force (IETF), its areas,
and its working groups. Note that other groups may also distribute
working documents as Internet-Drafts.
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Anshoo Sharma, HSS [Page 1]
Internet Draft M3UA Conformance Test Plan May 2003
Abstract
This document presents the test specification for M3UA (MTP3 User
Adaptation) protocol (RFC 3332), which can be used to test M3UA
implementations for conformance to the protocol definition. The list
of test is exhaustive and covers almost all the categories of test.
This draft can also be used in conjunction with M3UA specification by
implementers of protocol as implementers guide, as the pictorial
representation of various scenarios help easy understanding of the
protocol.
Next revision of the draft will cover the additions done to the
protocol revision and any subsequent RFC published by IETF.
Table of Contents
1. Introduction.......................................................3
1.1 Terms Used....................................................3
1.2 Change History................................................6
2. General Principles of M3UA Tests...................................6
2.1 Presentation of test descriptions.............................6
3. Test Configurations................................................7
3.1 Presentation of test Configurations...........................7
3.2 Configuration for testing the M3UA at SGP.....................8
3.3 Configuration for testing the M3UA at ASP....................12
4. Test Cases for Testing M3UA at SGP...............................16
4.1 Management...................................................16
4.2 Transfer.....................................................35
4.3 SSNM.........................................................47
4.4 ASPSM........................................................56
4.5 ASPTM........................................................64
4.6 SCTP Connection Management..................................101
4.7 Dynamic Routing Key Management..............................106
5. Test Cases for Testing M3UA at ASP..............................116
5.1 Management..................................................116
5.2 Transfer....................................................125
5.3 SSNM........................................................139
5.4 ASPSM.......................................................149
5.5 ASPTM.......................................................154
5.6 SCTP Connection Management..................................163
5.7 Dynamic Routing Key Management..............................167
6. Acknowledgements.................................................169
7. Authors' Addresses...............................................169
8. References.......................................................169
Copyright Statement..............................................170
Anshoo Sharma, HSS [Page 2]
Internet Draft M3UA Conformance Test Plan May 2003
1 Introduction
The M3UA is a protocol for the transport of any SS7 MTP3-User signaling
(e.g. ISUP and SCCP messages) over IP using the Stream Control
Transport Protocol (SCTP) or any other suitable transport protocol.
This protocol would be used between a Signaling Gateway (SG) and an
Application Service Provider (ASP) (e.g. Media Gateway Controller -
MGC) or IP-resident Database.
1.1 Terms Used
Application Server (AS) - A logical entity serving a specific Routing
Key. An example of an Application Server is a virtual switch element
handling all call processing for a unique range of PSTN trunks,
identified by an SS7 SIO/DPC/OPC/CIC_range. Another example is a
virtual database element, handling all HLR transactions for a
particular SS7 DPC/OPC/SCCP_SSN combination. The AS contains a set of
one or more unique Application Server Processes, of which one or more
is normally actively processing traffic. Note that there is a 1:1
relationship between an AS and a Routing Key.
Application Server Process (ASP) - A process instance of an Application
Server. An Application Server Process serves as an active or backup
process of an Application Server (e.g., part of a distributed virtual
switch or database). Examples of ASPs are processes (or process
instances) of MGCs, IP SCPs or IP HLRs. An ASP contains an SCTP
endpoint and may be configured to process signalling traffic within
more than one Application Server.
Association - An association refers to an SCTP association. The
association provides the transport for the delivery of MTP3-User
protocol data units and M3UA adaptation layer peer messages.
IP Server Process (IPSP) - A process instance of an IP-based
application. An IPSP is essentially the same as an ASP, except that it
uses M3UA in a point-to-point fashion. Conceptually, an IPSP does not
use the services of a Signalling Gateway node.
Failover - The capability to reroute signalling traffic as required to
an alternate Application Server Process, or group of ASPs, within an
Application Server in the event of failure or unavailability of a
currently used Application Server Process. Failover also applies upon
the return to service of a previously unavailable Application Server
Process.
Anshoo Sharma, HSS [Page 3]
Internet Draft M3UA Conformance Test Plan May 2003
Host - The computing platform that the process (SGP, ASP or IPSP) is
running on.
Layer Management - Layer Management is a nodal function that handles
the inputs and outputs between the M3UA layer and a local management
entity.
Linkset - A number of signalling links that directly interconnect two
signalling points, which are used as a module.
MTP - The Message Transfer Part of the SS7 protocol.
MTP3 - MTP Level 3, the signalling network layer of SS7
MTP3-User - Any protocol normally using the services of the SS7 MTP3
(e.g., ISUP, SCCP, TUP, etc.).
Network Appearance - The Network Appearance is a M3UA local reference
shared by SG and AS (typically an integer) that together with an
Signaling Point Code uniquely identifies an SS7 node by indicating the
specific SS7 network it belongs to. It can be used to distinguish
between signalling traffic associated with different networks being
sent between the SG and the ASP over a common SCTP association. An
example scenario is where an SG appears as an element in multiple
separate national SS7 networks and the same Signaling Point Code value
may be reused in different networks.
Network Byte Order: Most significant byte first, a.k.a Big Endian.
Routing Key: A Routing Key describes a set of SS7 parameters and
parameter values that uniquely define the range of signalling traffic
to be handled by a particular Application Server. Parameters within the
Routing Key cannot extend across more than a single Signalling Point
Management Cluster.
Routing Context - A value that uniquely identifies a Routing Key.
Routing Context values are either configured using a configuration
management interface, or by using the routing key management procedures
defined in this document.
Signalling Gateway Process (SGP) - A process instance of a Signalling
Gateway. It serves as an active, backup, load-sharing or broadcast
process of a Signalling Gateway.
Anshoo Sharma, HSS [Page 4]
Internet Draft M3UA Conformance Test Plan May 2003
Signalling Gateway - An SG is a signaling agent that receives/sends SCN
native signaling at the edge of the IP network [11]. An SG appears to
the SS7 network as an SS7 Signalling Point. An SG contains a set of
one or more unique Signalling Gateway Processes, of which one or more
is normally actively processing traffic. Where an SG contains more
than one SGP, the SG is a logical entity and the contained SGPs are
assumed to be coordinated into a single management view to the SS7
network and to the supported Application Servers.
Signalling Process - A process instance that uses M3UA to Communicate
with other signalling processes. An ASP, an SGP and an IPSP are all
signalling processes.
Signalling Point Management Cluster (SPMC) - The complete set of
Application Servers represented to the SS7 network under a single MTP
entity (Signalling Point) in one specific Network Appearance. SPMCs are
used to aggregate the availability, congestion, and user part status of
an MTP entity (Signalling Point) that is distributed in the IP domain,
for the purpose of supporting MTP3 management procedures towards the
SS7 network. In some cases, the SG itself may also be a member of the
SPMC. In this case, the SG availability /congestion /User_Part status
should also be taken into account when considering any supporting MTP3
management actions.
Stream - A stream refers to an SCTP stream; a unidirectional logical
channel established from one SCTP endpoint to another associated SCTP
endpoint, within which all user messages are delivered in-sequence
except for those submitted to the unordered delivery service.
ASPSM, ASPTM, SSNM - ASP State Maintenance Messages, ASP Traffic
Maintenance Messages, Signalling System Network Management Messages.
Anshoo Sharma, HSS [Page 5]
Internet Draft M3UA Conformance Test Plan Jan 2003
1.2 Change History
1.2.1 Changes from draft-anshoo-test-spec-m3ua-00.txt
1. Test Case for Missing Mandatory Parameter.
Test Case Number (SGP Side) : 1.15
Test Case Number (ASP Side) : 1.9
2. Test Case for Unsupported Dynamic Registration
Test Case Number (SGP Side) : 1.16
3. Test Case for sending ASP Failure Notification from SGP.
Test Case Number (SGP Side) : 1.17
4. Test Case for sending DATA from ASP only in Active State of AS.
Test Case Number (ASP Side) : 2.7
2 General Principles of M3UA Tests
These tests aim to verify a given implementation of a protocol in
accordance with the relevant draft. The specification is independent of
a given implementation and does not generally imply any modification of
the endpoint under test. However, it is recognized that certain tests
require capabilities of the system that are not explicitly defined in
the draft, and these capabilities may not be present in all
implementations. As a consequence, certain tests may not be possible in
all implementations.
2.1 Presentation of test descriptions
Each test description includes the environment in which the point under
test must be inserted in order to pass the test. Nine test
configurations are defined (named A, B, C, D, E, F, G, H, I and J);
they are presented in clause 3.
Each test is precisely described. Nevertheless, some events not
directly concerning the point under test, or without direct link with
the test nature, are not explicitly described. In order to preserve the
test description implementation independence, certain flexibility has
been left in the test descriptions. This is particularly the case when
it is necessary to terminate the SCTP association (where it is only
mentioned "Terminate" with no more precision). The operator will choose
according to the implementation particularities and the events expected
in the test description, the appropriate Termination means (MML- Man
machine Language, provoked failure, etc.).
Anshoo Sharma, HSS [Page 6]
Internet Draft M3UA Conformance Test Plan Jan 2003
2.1.1 Pre Test Condition
Before starting the test we need to get the setup into a condition from
where test can be started. These conditions are specified in Pre-Test
condition in each test.
Note: Where NIF has been written, it means that NIF+SM. In some
implementation these may be two entities and in some, they may be
implemented in single entity.
3 Test Configurations:
The set of tests described in this Recommendation assumes that the
point under test is inserted in a test environment called "test
configuration".
3.1 Presentation of test configurations:
There are different configurations for testing the M3UA protocol. These
configurations and hence test cases have been divided on the basis of
M3UA at SG and M3UA at AS.
Anshoo Sharma, HSS [Page 7]
Internet Draft M3UA Conformance Test Plan Jan 2003
3.2 Configuration for testing the M3UA at SGP:
3.2.1 Configuration A:
This simple configuration is used for all the procedures of tests
concerning only one AS. Configuration A is shown in figure 1. AS is
handling the traffic for routing context P and N/w Appearance A. AS is
having only one ASP ASP1. SG routes Data to SS7 for PC Z. SGP serves
SG.
Routing Context P may be based on the following information:
1. DPC
2. DPC+CIC+SIO
3. DPC+SIO
4. DPC+SSN
SG
+-------------+ +--------------+
| SGP/IPSP | | AS DPC = X |
| under Test | | ------- |
| DPC = Z |-------------------------------|--| ASP1 | |
| | | ------- |
+-------------+ +--------------+
Fig 1: Configuration A
3.2.2 Configuration B:
This configuration is used for all the procedures of tests concerning
one ASP in two AS which is handling traffic for both AS. Configuration
B is shown in figure 2. AS1 is handling the traffic for routing context
P and N/w Appearance A. AS2 is handling the traffic for routing context
Q and N/w Appearance A. ASP1 is in both AS. Point Code of SG/IPSP is Z
and SGP serves SG.
Routing Context P and Q may be based on the following information:
1. DPC
2. DPC+CIC+SIO
3. DPC+SIO
4. DPC+SSN
Anshoo Sharma, HSS [Page 8]
Internet Draft M3UA Conformance Test Plan Jan 2003
+--------------+
SG | AS1 DPC X |
+-------------+ | ------- |
| |-------------------------------| | ASP1 | |
| SGP/IPSP | | ------- |
| Under Test | +--------------+
| DPC Z | +--------------+
| |-------------------------------| AS2 DPC Y |
+-------------+ | ------- |
| | ASP1 | |
| ------- |
+--------------+
Fig 2: Configuration B
3.2.3 Configuration C:
This configuration is used for all the procedures of tests concerning
two or more ASP in one AS. Configuration C is shown in figure 3. AS is
handling the traffic for routing context P and N/w Appearance A. ASP1
and ASP2 can be in FAIL-OVER mode, LOADSHARE or BROADCAST mode of
traffic handling. Point Code of SG/IPSP is Z and SGP serves SG.
Routing Context P may be based on the following information:
1. DPC
2. DPC+CIC+SIO
3. DPC+SIO
4. DPC+SSN
+--------------+
SG | AS DPC X |
+-------------+ | ------- |
| |-------------------------------|-| ASP1 | |
| SGP/IPSP | | ------- |
| Under Test | | ------- |
| DPC Z | | | ASP2 | |
| |-------------------------------|- ------- |
+-------------+ +--------------+
Fig 3: Configuration C
Anshoo Sharma, HSS [Page 9]
Internet Draft M3UA Conformance Test Plan Jan 2003
3.2.4 Configuration D:
This configuration is used for all the procedures of tests concerning
two or more AS which are handling traffic for different network
appearance and different routing context. Configuration D is shown in
figure 4. AS1, AS2 are handling the traffic for N/w Appearance A and
AS3 is handling traffic for N/w appearance B. SGP serves SG.
AS1 is handling traffic for Routing Context P, AS2 is handling traffic
for Routing Context Q and AS3 is handling traffic for Routing Context
R.
+--------------+
SG | AS1 DPC X |
+-------------+ | ------- |
| |-------------------------------| | ASP1 | |
| SGP/IPSP | | ------- |
| Under Test | +--------------+
| DPC Z | +--------------+
| |-------------------------------| AS2 DPC Y |
| |-------+ | ------- |
+-------------+ | | | ASP2 | |
| | ------- |
| +--------------+
| +--------------+
| | AS3 DPC T |
+-----------------------|- ------- |
| | ASP 3 | |
| ------- |
+--------------+
Fig 4: Configuration D
3.2.5 Configuration E:
This configuration is used for all the procedures of tests concerning
two AS which are handling traffic for two Routing Contexts.
Configuration E is shown in figure 5. AS1 is handling the traffic for
routing context P. AS2 is handling the traffic for Routing Context Q.
ASP1 is in AS1 and ASP2 is in AS2. Routing Contexts are sharing the
point code. SGP serves SG.
Anshoo Sharma, HSS [Page 10]
Internet Draft M3UA Conformance Test Plan Jan 2003
+--------------+
SG | AS1 DPC X |
+-------------+ | ------- |
| |-------------------------------| | ASP1 | |
| SGP/IPSP | | ------- |
| Under Test | +--------------+
| DPC Z | +--------------+
| |-------------------------------| AS2 DPC X |
+-------------+ | ------- |
| | ASP2 | |
| ------- |
+--------------+
Fig 5: Configuration E
3.2.6 Configuration F:
This configuration is used for all the procedures of tests concerning
AS serving different SIO. Configuration F is shown in figure 6. AS1 is
handling the traffic for routing context P, AS2 is handling for routing
context Q and AS3 for routing context R. All AS are handling traffic
for N/w appearance A. Point Code of SG/IPSP is Z. AS1 and AS2 are
serving the SIO ISUP but different CIC range and AS3 is serving the SIO
SCCP. SGP serves SG.
+--------------+
SG | AS1 DPC X |
+-------------+ | ------- |
| |-------------------------------| | ASP1 | |
| SGP/IPSP | | ------- |
| Under Test | +--------------+
| DPC Z | +--------------+
| |-------------------------------| AS2 DPC X |
| |-------+ | ------- |
+-------------+ | | | ASP2 | |
| | ------- |
| +--------------+
| +--------------+
| | AS3 DPC X |
+-----------------------|- ------- |
| | ASP 3 | |
| ------- |
+--------------+
Fig 6: Configuration F
Anshoo Sharma, HSS [Page 11]
Internet Draft M3UA Conformance Test Plan Jan 2003
3.3 Configuration for testing the M3UA at ASP
3.3.1 Configuration G:
This simple configuration is used for all the procedures of tests
concerning only one SG/IPSP. Configuration G is shown in figure 7.
SG routes Data to SS7 for PC Z and SGP serves SG. ASP is handling
the traffic for routing context P.
Routing Context P may be based on the following information:
1. DPC
2. DPC+CIC+SIO
3. DPC+SIO
4. DPC+SSN
+-------------+ +--------------+
| ASP1 | | SGP/IPSP |
| under Test | | DPC = Z |
| DPC = X |-------------------------------| SG |
| | | |
+-------------+ +--------------+
Fig 7: Configuration G
3.3.2 Configuration H:
This configuration is used for all the procedures of tests concerning
two SGs/IPSPs connected to the same ASP and handling traffic for the
same DPC in the SEP network. Configuration H is shown in figure 8.
SGP1/IPSP1 serving SG1 and SGP2/IPSP2 serving SG2 are handling the
traffic for N/w Appearance A.
Point Code of SG1/IPSP1 is Y and of SG2/IPSP2 is Z.
Routing Context P may be based on the following
information:
1. DPC
2. DPC+CIC+SIO
3. DPC+SIO
4. DPC+SSN
Anshoo Sharma, HSS [Page 12]
Internet Draft M3UA Conformance Test Plan Jan 2003
+--------------+
| SGP1/IPSP1 |
+-------------+ | DPC Y |
| |-------------------------------| SG1 |
| ASP1 | | |
| Under Test | --------------
| DPC X | +--------------+
| |-------------------------------| SGP2/IPSP2 |
+-------------+ | DPC Y |
| SG2 |
| |
+--------------+
Fig 8: Configuration H
3.3.3 Configuration I:
This simple configuration is used for all the procedures of tests
concerning one ASP in two AS. Configuration I is shown in figure 9.
Point Code of SG/IPSP is Z. ASP1 is in two AS, AS1 and AS2. AS1 is
handling traffic for routing context P and AS2 is handling traffic for
routing context Q. Routing Context P and Q may be based on the
following information:
1. DPC
2. DPC+CIC+SIO
3. DPC+SIO
4. DPC+SSN
+--------------+
| Under Test |
| AS1 DPC X |
| ------- | +----------------+
| | ASP1 | | ---------------------| |
| ------- | | SGP / IPSP |
+--------------+ | |
+--------------+ | DPC Z |
| AS2 DPC Y | | SG |
| ------- | ---------------------| |
| | ASP1 | | +----------------+
| ------- |
| Under Test |
+--------------+
Fig 9: Configuration I
Anshoo Sharma, HSS [Page 13]
Internet Draft M3UA Conformance Test Plan Jan 2003
3.3.4 Configuration J:
This configuration is used for all the procedures of tests concerning
two SGPs in an SG connected to the same ASP. SG is handling traffic
for Point Code Y and SGP1 and SGP2 are serving the SG. The ASP is
handling Traffic for Routing Context P. Configuration J is shown in
figure 10. The SG can be in Broadcast, Loadshare or Override Mode.
Routing Context P may be based on the following information:
1. DPC
2. DPC+CIC+SIO
3. DPC+SIO
4. DPC+SSN
+--------------+
| SGP1 |
+-------------+ | DPC Y |
| |-------------------------------| SG |
| ASP1 | | |
| Under Test | +--------------+
| DPC X | +--------------+
| |-------------------------------| SGP2 |
+-------------+ | DPC Y |
| SG |
| |
+--------------+
Fig 10 : Configuration J
3.3.4 Configuration K:
This configuration is used for all the procedures of tests concerning
four SGPs connected to the same ASP. Both SG1 and SG2 are handling
traffic for PC X and Y. ASP1 is handling traffic for routing context P.
Point Code of SG1/IPSP1 is Y and of SG2/IPSP2 is Z. The SGs can be in
Broadcast, Loadshare or Override Mode. Configuration J is shown in
Figure 11. Routing Context P may be based on the following
information:
1. DPC
2. DPC+CIC+SIO
3. DPC+SIO
4. DPC+SSN
Anshoo Sharma, HSS [Page 14]
Internet Draft M3UA Conformance Test Plan Jan 2003
+--------------+
+-------------+ | SGP1 (SG1) |
| |-------------------------------| DPC Y |
| | +--------------+
| | +--------------+
| | | SGP2 (SG1) |
| ASP1 |-------------------------------| DPC Y |
| Under Test | +--------------+
| DPC X | +--------------+
| | | SGP3 (SG2) |
| |-------------------------------| DPC Y |
| | +--------------+
| | +--------------+
| |-------------------------------| SGP4 (SG2) |
+-------------+ | DPC Y |
+--------------+
Fig 11 : Configuration K
Anshoo Sharma, HSS [Page 15]
Internet Draft M3UA Conformance Test Plan Jan 2003
4. Test Cases for Testing M3UA at SGP
Following Tests are to be carried out when the Implementation Under
Test is SGP.
4.1 MANAGEMENT
Test Cases covering MANAGEMENT Procedures.
"Notify Message with AS Status"
+ TEST NUMBER : 1.1
+ TITLE : AS management
+ SUBTITLE : Notify Message with AS status
+ PURPOSE: To check that if ASPDN, ASPUP, ASPAC and ASPIA messages are
received in ASP-Active, ASP-Down, ASP-Up and ASP-Active state
respectively then NTFY message with correct status is sent to ASP.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is Active. Also arrange the data in ASP such that ASPDN,
ASPUP messages are sent from ASP to SGP for ASP and these are sent
on stream zero. The value of N/w Appearance is A and Routing Context
is P in all the messages and other parameters are having valid
values.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM
ASP is active
ASPDN --------------->
(ASP1) Status Ind ---------->
<-------------- ASP-Down-Ack
| Status Ind ---------> (AS Pending)
|
|Time = z sec
|
|Timer T(r) Expiry
|
--- Status Ind ---------> (AS Down)
Anshoo Sharma, HSS [Page 16]
Internet Draft M3UA Conformance Test Plan Jan 2003
ASPUP --------------->
(ASP1) Status Ind ----------->
<-------------- ASP-Up-Ack
<-------------- NTFY (AS-Inactive)
ASPAC --------------->
(ASP1) Status Ind ----------->
<-------------- ASP-Active-Ack
<-------------- NTFY (AS-Active)
ASPIA --------------->
(ASP1) Status Ind ----------->
<-------------- ASP-Inactive-Ack
<-------------- NTFY (AS-Pending)
TEST DESCRIPTION:
1. Send ASPDN message for ASP1 from ASP to the SGP.
2. Check A: ASPDN is acknowledged by ASP-Down-Ack
message at the ASP.
3. Send ASPUP message to SGP.
4. Check B: SGP responds with ASP-UP-Ack message and NTFY
(AS-Inactive).
5. Send ASPAC message with Routing Context P and check SGP responds
with ASP-Active-Ack and NTFY with status AS-Active. Repeat the test
case with Routing Context parameter not present in ASPAC message.
6. Send ASPIA message and check that SGP responds with ASP Inactive-Ack
and NTFY with status AS-Pending.
7. Check E: NTFY message is received on stream 0.
Anshoo Sharma, HSS [Page 17]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Notify Message with Insufficient Resources in AS"
+ TEST NUMBER : 1.2
+ TITLE : AS management
+ SUBTITLE : Notify Message with Insufficient Resources in AS
+ PURPOSE: To check that if the number of Active ASPs in a Loadshare /
Broadcast AS goes below the minimum number of required ASPs then a
NTFY message for Insufficient Resources is sent to INACTIVE ASPs.
+ TEST CONFIGURATION: C
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1 and ASP2. ASP1 is Active for RC P and ASP2 is Inactive in SGP.
The AS is in Loadshare mode and the minimum number of Active ASPs
required is two. Also arrange the data in ASP1 such that ASPIA
messages is sent from ASP1 to SGP for Routing Context P.
EXPECTED MESSAGE SEQUENCE :
ASP1 ASP2 SGP SM
ASP1 is Active
ASP2 is Active
ASPIA --------------->
(ASP1)
<-------------- ASP-Inactive-Ack
Status Ind ---------->
(ASP2)<---------- NTFY (Insufficient Resources)
(ASP1)<----------------- NTFY (Insufficient Resources)
TEST DESCRIPTION:
1. Send ASPIA message from ASP1 to the SGP.
2. Check A: SGP sends a NTFY Message with Insufficient Resources for
RC P to ASP2 which is in ASP-Inactive State.
3. Check B: ASPIA is acknowledged by ASPIA-Ack message by the SGP to
ASP1.
4. Repeat the Test Case when the AS is in Broadcast Mode.
Note: This NTFY message might not be provisioned by some
implementations.
Anshoo Sharma, HSS [Page 18]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Invalid Version Error"
+ TEST NUMBER : 1.3
+ TITLE : Invalid Message Handling
+ SUBTITLE : Invalid Version Error
+ PURPOSE: To check that if any message with Invalid version is
received at the SGP then SGP responds with ERROR message containing
cause "Invalid Version" and diagnostic information filled with the
version the SGP supports.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is Active. Also arrange the data in ASP such that ASPIA
message is sent with the version other than Version 1.0 protocol to
SGP. Type field can be any valid value and fill the routing context
with any value.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
AS is active
ASPIA ---------------->
Version = 2
<--------------- ERROR
Cause = Invalid Version
TEST DESCRIPTION:
1. Send ASPIA message ASP to SGP containing version 2 in the common
header.
2. Check A: ERROR message is received at the ASP containing cause
Invalid Version.
3. Check B: Diagnostic Field Parameter in ERROR is filled with
version 1.
4. Repeat the above test cases for other messages from ASP to SGP like
ASPAC, ASPUP, ASPDN, DAUD and DATA. In all these cases ERROR message
will be received with the same cause.
Anshoo Sharma, HSS [Page 19]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Invalid Traffic Handling Mode Error"
+ TEST NUMBER : 1.4
+ TITLE : Invalid Message Handling
+ SUBTITLE : Invalid Traffic Handling Mode Error
+ PURPOSE: To check that if ASPAC or ASPIA message is received with
Type parameter incompatible with the traffic handling mode currently
used in AS at SGP, SGP responds with ERROR message containing cause
"Invalid Traffic Handling Mode".
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP1 is Up. Arrange the data in ASP such that ASPAC
message is sent with Type field filled with Loadshare mode of Traffic
handling. Traffic Handling Mode defined at SGP for AS is Override.
Fill value P in Routing context parameter.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
AS is Inactive
ASPAC ---------------->
Type = Loadshare
<--------------- ERROR
Cause = Invalid traffic Handling Mode
TEST DESCRIPTION:
1. Send ASPAC message from ASP to SGP containing Type field Loadshare.
Mode of Traffic handling for AS at SGP is Override.
2. Check A: ERROR message is received at the ASP containing cause
Invalid Traffic Handling Mode.
3. Repeat the above test cases for other values of Type field with
Traffic Handling Mode for AS at SGP being different from this Type
field.
4. Repeat the test case with Type field having value that is not
defined i.e. any value greater than 0x03.
5. Repeat all the above tests for ASPIA message.
Anshoo Sharma, HSS [Page 20]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Invalid Traffic Handling Mode Error if there are two ASP in one AS"
+ TEST NUMBER : 1.5
+ TITLE : Invalid Message Handling
+ SUBTITLE : Invalid Traffic Handling Mode Error if there are two ASP
in one AS
+ PURPOSE: To check that if ASPAC or ASPIA message is received with
Type parameter incompatible with the traffic handling mode currently
used in AS at SGP, SGP responds with ERROR message containing cause
"Invalid Traffic Handling Mode".
+ TEST CONFIGURATION: C
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP1 and ASP2 are Up. Arrange the data in ASPs such that
ASPAC message for ASP1 is sent with Type field filled with Override
mode of Traffic handling and ASPAC message for ASP2 is sent with Type
field filled with Loadshare mode of Traffic handling. Traffic
Handling Mode defined at SGP for AS is Override Mode. Fill value P in
Routing context parameter.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
AS is Inactive
ASPAC(ASP1)---------------->
Type = Override Status Ind ------->
<--------------- ASP-Active-Ack
ASPAC(ASP2) ---------------->
Type = Loadshare
<--------------- ERROR
Cause = Invalid traffic Handling Mode
TEST DESCRIPTION:
1. Send ASPAC message from ASP1 to SGP containing Type field Override.
2. Check A: ASP-Active-Ack message is received at the ASP.
3. Send ASPAC message from ASP2 to SGP containing Type field Loadshare.
4. Check B: ERROR message is received at the ASP containing cause
Invalid Traffic Handling Mode.
5. Repeat the above test cases for other values of Type field with
Traffic Handling Mode for AS at SGP being different from this Type.
Anshoo Sharma, HSS [Page 21]
Internet Draft M3UA Conformance Test Plan Jan 2003
6. Repeat the test case with Type field having value that is not
defined.
7. Repeat all the above tests for ASPIA message.
Anshoo Sharma, HSS [Page 22]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Unrecognized Message Type"
+ TEST NUMBER : 1.6
+ TITLE : Invalid Message Handling
+ SUBTITLE : Unrecognized Message Type
+ PURPOSE: To check that if a message with message type not defined is
received at SGP, SGP responds with ERROR message containing cause
"Invalid Message Type".
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP1 is active. Arrange the data in ASP such that a message
with Message type not defined is sent to SGP. Let the other
parameters in the message be like any other message.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Active
Message ---------------->
Message Type=0x408
<--------------- ERROR
Cause = Invalid Message Type
DATA ---------------->
N/w Appearance A
MTP-Transfer Ind ------->
TEST DESCRIPTION:
1. Send a message with message type 0x408 or any other value which is
not defined from ASP to SGP.
2. Check A: ERROR message is received at the ASP containing cause
Invalid Message Type.
3. Check B: State of AS at SGP is not disturbed.
4. Repeat the above test cases by sending DUNA, DAVA, DUPU, DRST
messages from ASP which the SGP is not expected to receive. In this
case Error will be reported to the SM and Message will be discarded.
Anshoo Sharma, HSS [Page 23]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Invalid Network Appearance"
+ TEST NUMBER : 1.7
+ TITLE : Invalid Message Handling
+ SUBTITLE : Invalid Network Appearance and Invalid Routing Context
+ PURPOSE: To check that if a message with invalid network appearance
i.e. network appearance not defined at SGP then SGP responds with
ERROR message containing cause "Invalid Network Appearance".
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is in AS-Active state i.e. ASP1 is active. Arrange the
data in ASP such that DATA message with Network Appearance other
than A is sent to SGP.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Active
DATA ---------------->
N/w Appearance B
<--------------- ERROR
Cause = Invalid N/w Appearance
DATA ---------------->
N/w Appearance A
MTP-Transfer Ind ------->
TEST DESCRIPTION:
1. Send DATA message with network appearance B which is not defined at
SGP.
2. Check A: ERROR message containing cause Invalid Network Appearance
should be received at AS.
3. Check B: State of AS at SGP is not disturbed.
4. Repeat the Test for an unconfigured Routing Context ERROR message
with Invalid Routing Context must be returned.
Note: Network Appearance and Routing Context parameters are optional.
In some implementation this parameter may not come in DATA message.
In those implementations, this test case need not be tested.
Anshoo Sharma, HSS [Page 24]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Message length less than the length of mandatory Parameters"
+ TEST NUMBER : 1.8
+ TITLE : Invalid Message Handling
+ SUBTITLE : Message length less than the length of mandatory
parameters
+ PURPOSE: To check that if a message with value of length parameter
less than length of mandatory parameters is received then message is
discarded.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and AS is in AS-Active state. Arrange the data in AS such that
ASPIA message with length parameter filled with value less than the
length of type parameter is sent.
EXPECTED MESSAGE SEQUENCE :
ASP SGP NIF
AS is Active
ASPIA ---------------->
Message Length = 2
<--------------- Error
( Unsupported Message Type)
DATA ---------------->
N/w appearance A, RC = P
MTP-Transfer --------->
TEST DESCRIPTION:
1. Send ASPIA message with length parameter filled with value less than
the length of type field to the SGP.
2. Check A: SGP will send an Error message with Unsupported Message
Type parameter.
3. Check B: State of AS at SGP is not disturbed.
4. Repeat the above test case for other messages like ASPAC, ERROR,
ASPDN.
Anshoo Sharma, HSS [Page 25]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ERROR Message Handling"
+ TEST NUMBER : 1.9
+ TITLE : ERROR
+ SUBTITLE : Handling of Received Error
+ PURPOSE: To check that if an error is received then that is reported
to the SM and no action is taken against that.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is active. Arrange data in ASP such that ERROR with cause
invalid version is sent to the SGP.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Active
ERROR ---------------->
cause=Invalid version
Error ------->
TEST DESCRIPTION:
1. Send ERROR message with cause invalid version from ASP to SGP.
2. Check A: Error should be reported to the SM.
3. Check B: Further action at the SGP are implementation dependent.
SM may tear down the connection or no action may be taken.
4. Repeat the test case for other cause values in ERROR message.
Anshoo Sharma, HSS [Page 26]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Error - Refused - Management Blocking"
+ TEST NUMBER : 1.10
+ TITLE : ERROR
+ SUBTITLE : ASPUP and ASPAC messages are sent for a Blocked ASP then
ERROR message is sent from SGP.
+ PURPOSE: To check that if an error is received then that is reported
to the SM and no action is taken against that.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is in ASP-Down state. Arrange data in ASP such that ASPUP
and ASPAC messages are sent to SGP with valid parameters.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Down
ASPUP ---------------->
<--------------- Error
(Refused - Management Blocking)
ASPAC ---------------->
<--------------- Error
(Refused - Management Blocking)
TEST DESCRIPTION:
1. Send ASPUP message from ASP to SGP.
2. Check A: Error should be sent from SGP with "Refused - Management
Blocking" to ASP.
3. Send ASPAC message from ASP to SGP.
4. Check A: Error should be sent from SGP with "Refused - Management
Blocking" to ASP.
Anshoo Sharma, HSS [Page 27]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Error - Invalid Stream Identifier"
+ TEST NUMBER : 1.11
+ TITLE : ERROR
+ SUBTITLE : Stream Zero for Non-Transfer Messages for Multiple Stream
SCTP association.
+ PURPOSE: If Non Transfer messages with the exception of ASPTM, BEAT
and BEAT-Ack are sent on any Stream other than Zero then ERROR
message is sent from SGP.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is in ASP-Down state. Arrange data in ASP such that ASPUP
is sent to SGP with valid parameters on stream 1.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Down
ASPUP ---------------->
(stream 1)
<--------------- Error
(Invalid Stream Identifier)
TEST DESCRIPTION:
1. Send ASPUP message from ASP to SGP on Stream 1.
2. Check A: Error should be sent from SGP with "Invalid Stream
Identifier" to ASP.
3. Repeat the Test Case for all Non-Transfer messages other than
ASPTM, BEAT and BEAT-Ack.
Anshoo Sharma, HSS [Page 28]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Reception of Unpadded Message"
+ TEST NUMBER : 1.12
+ TITLE : ERROR
+ SUBTITLE : On Receiving Unpadded message from Peer, SGP should still
process the Message.
+ PURPOSE: If the SGP receives a Message from the ASP which is not
padded, then also the Message should be Processed.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is in ASP-Down state. Arrange data in ASP such that ASPUP
is sent to SGP with size of Info String such that the Total
Message Length is 35 Bytes and this Message should not be padded.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Down
ASPUP ---------------->
(Length is 35 Bytes)
<---------------- ASPUP-Ack
<---------------- NTFY
TEST DESCRIPTION:
1. Send the ASPUP message as described from ASP to SGP on Stream 0.
2. Check A: The Message should not be rejected at the SGP.
3. Check B: ASP UP Ack and NTFY should be sent from the SGP side.
Anshoo Sharma, HSS [Page 29]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Error - ASP ID Required"
+ TEST NUMBER : 1.13
+ TITLE : ERROR
+ SUBTITLE : Error with cause ASP Identifier Required.
+ PURPOSE: On Receiving an ASPUP Message from an unconfigured
Transport Address without an ASP ID the SGP sends ERROR with cause
"ASP ID Required".
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is in ASP-Down state. Arrange data in ASP such that ASPUP
is sent to SGP with no ASP ID. The Transport Address of the ASP has
not been configured at the SGP side.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Down
ASPUP ---------------->
(No ASP ID)
<---------------- ERROR
(ASP ID Required)
TEST DESCRIPTION:
1. Send ASPUP message from ASP to SGP.
2. Check A: An Error Message with cause ASP ID Required is sent to the
ASP from the SGP.
Anshoo Sharma, HSS [Page 30]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Error - Invalid ASP ID"
+ TEST NUMBER : 1.14
+ TITLE : ERROR
+ SUBTITLE : Error with cause Invalid ASP Identifier.
+ PURPOSE: On receiving a Non-Unique ASP Identifier in the ASPUP
message an ERROR with cause Invalid ASP Identifier is sent to the
ASP.
+ TEST CONFIGURATION: B
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
both ASPs (i.e. ASP1 and ASP2). ASP1 is in ASP-Inactive state and the
ASP Identifier for ASP1 is 'T'. ASP2 is in ASP-Down State. Arrange
data at ASP2 for sending an ASPUP to SGP with ASP ID as 'T'.
EXPECTED MESSAGE SEQUENCE :
ASP2 SGP SM + NIF
ASP1 is Inactive
ASP2 is Down
From ASP2
ASPUP ---------------->
(ASP ID 'T')
(ASP2) <---------------- ERROR
(Invalid ASP ID)
TEST DESCRIPTION:
1. Send ASPUP message from ASP to SGP with ASP ID 'T'.
2. Check A: An Error Message with cause Invalid ASP ID Required is sent
to the ASP from the SGP and the ASPUP message is discarded.
Anshoo Sharma, HSS [Page 31]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Error - Missing Parameter"
+ TEST NUMBER : 1.15
+ TITLE : ERROR
+ SUBTITLE : Error with cause Missing Parameter.
+ PURPOSE: To check that if any message without mandatory parameter is
received at the SGP then SGP responds with ERROR message containing
cause "Missing Parameter".
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is Active. Also arrange the data in ASP such that Payload
Data Message is sent without Protocol Data parameter.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Active
From ASP
DATA ---------------->
(Without Payload)
(ASP) <---------------- ERROR
(Missing Parameter)
TEST DESCRIPTION:
1. Send Payload Data message ASP to SGP without Protocol Data
parameter.
2. Check A: ERROR message is received at the ASP containing Error Code
Missing Parameter.
3. Repeat the above test cases for other messages from ASP to SGP like
REG REQ, DEREG REQ, SCON and DAUD without mandatory parameter. In
all these cases ERROR message will be received with the same Error
Code.
Anshoo Sharma, HSS [Page 32]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Error - Unsupported Message Class"
+ TEST NUMBER : 1.16
+ TITLE : ERROR
+ SUBTITLE : Error Type - Unsupported Message Class.
+ PURPOSE: To verify that A SGP that does not support registration must
return an Error (Unsupported Message Class) (optionally with the
message with the first 40 bytes of the offending message). This Error
should be returned whenever an unsupported or invalid Message Type is
received.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP
and ASP. Dynamic Routing Key Registration is not supported at the
SGP. The ASP is in Inactive State at the SGP. Arrange Data in
ASP such that a Routing Key Registration request for RK1 is sent
from ASP to SGP on stream 0.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Inactive
REG REQ ----------------->
<----------------- Error (Unsupported Message Class)
TEST DESCRIPTION:
1. Send a valid Reg Req message for RK1 from ASP to SGP Stack.
2. Check A: Verify that the SGP send a error message "Unsupported
Message Class" with the first 40 bytes of the offending message
to the ASP.
Anshoo Sharma, HSS [Page 33]
Internet Draft M3UA Conformance Test Plan Jan 2003
"NTFY - ASP Failure"
+ TEST NUMBER : 1.17
+ TITLE : NOTIFY
+ SUBTITLE : Sending of ASP Failure Notification
+ PURPOSE: To check that when any of the ASP's fail at SG. Notification
ASP failure is send to all up/active ASP's with ASP ID (if available)
of the failed ASP.
+ TEST CONFIGURATION: C
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1, ASP2. ASP1, ASP2 is in ASP-inactive state.
EXPECTED MESSAGE SEQUENCE :
ASP1 ASP2 SGP SM + NIF
ASP1 & ASP2 are Inactive
ASPAC ----------------->
(ASP1) Status Ind ----------->
<-------------- ASP-Active-Ack
<-------------- NTFY (AS-Active)
*** Terminate the SCTP Association between ASP1 and SGP ***
Status Ind ----------->
<------- NTFY (AS-Pending) to ASP2
<------- NTFY (ASP-Failure) to ASP2
TEST DESCRIPTION:
1. Send ASPAC message from ASP1 for related AS. ASP1 becomes active at
SGP.
2. Terminate the association between SGP and ASP1.
3. Check that AS PENDING notification is sent to ASP2.
4. Check that ASP FAILURE notification is sent to ASP2 with the ASP ID
(if available) of ASP1.
Anshoo Sharma, HSS [Page 34]
Internet Draft M3UA Conformance Test Plan Jan 2003
4.2 TRANSFER
Test Cases to test TRANSFER Procedures.
"Send and Receive Transfer Primitive in AS Active State"
+ TEST NUMBER : 2.1
+ TITLE : MTP-Transfer Primitive
+ SUBTITLE : Send and Receive Transfer Primitive in AS Active State
+ PURPOSE: To check that on receiving Transfer primitive from NIF, DATA
message is sent to the AS.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP1 is active. Also arrange the data in SGP such that upper
layers send MTP-Transfer indication primitive to M3UA with data to be
sent to DPC X, N/w Appearance A and RC P.
EXPECTED MESSAGE SEQUENCE :
ASP SGP NIF
a) ASP is Active
<----------- MTP-Transfer
<------------- DATA N/w appearance A
b)
DATA -------------->
MTP-Transfer --------->
TEST DESCRIPTION:
1. Send Transfer Request Primitive from the NIF at SGP side to send
Protocol Data to the ASP.
2. Check A: DATA message should be received at the ASP containing the
data passed by the NIF, Network Appearance and the RC for which the
DATA is being sent.
3. Send DATA message from ASP containing Protocol Data and Network
Appearance A that is known to SGP.
4. Check B: Transfer primitive is received at the NIF with the Protocol
Data.
5. Repeat the test step 3 if N/w Appearance parameter and RC is not
present in the DATA message sent from ASP to SGP.
Anshoo Sharma, HSS [Page 35]
Internet Draft M3UA Conformance Test Plan Jan 2003
Note: Network Appearance and Routing Context are optional parameters.
In some implementation these parameter will not be present in
DATA message sent from SGP to ASP and vice versa.
Anshoo Sharma, HSS [Page 36]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Stream Selection"
+ TEST NUMBER : 2.2
+ TITLE : Stream Selection
+ SUBTITLE : Stream Selection
+ PURPOSE: To check that all the messages for the same call are sent on
the same SCTP stream.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP with two or more streams. ASP1 is active. Also arrange the data
in SGP such that NIF send three or more Transfer indication primitive
to M3UA with N/w Appearance A and Routing Context P, containing the
Data with same CIC value to be sent to DPC X.
EXPECTED MESSAGE SEQUENCE :
ASP SGP NIF
ASP is active
<--------- MTP-Transfer
Check Stream id <------------- DATA Data with CIC X
<--------- MTP-Transfer
Check Stream id <------------- DATA Data with CIC X
<--------- MTP-Transfer
Check Stream id <------------- DATA Data with CIC X
TEST DESCRIPTION:
1. Send three or more Transfer Request Primitive from the NIF at SGP
side to send Protocol Data to the ASP. In the Protocol Data CIC
values should be same in all Transfer Request primitive assuming
load sharing across streams is based on CIC.
2. Check A: DATA messages are received at the ASP1 containing the same
Stream Sequence number.
3. Repeat the above test with same SLS value in Protocol Data in all
Transfer Request primitive assuming load sharing across the streams
is based on SLS.
4. Repeat the above test case with different CIC values and different
Anshoo Sharma, HSS [Page 37]
Internet Draft M3UA Conformance Test Plan Jan 2003
SLS values. DATA messages should be sent on different streams.
Note: How the messages will be distributed on different streams based
on CIC and SLS is implementation dependent.
Anshoo Sharma, HSS [Page 38]
Internet Draft M3UA Conformance Test Plan Jan 2003
"DATA message from ASP in ASP-Down state"
+ TEST NUMBER : 2.3
+ TITLE : Invalid Message Handling
+ SUBTITLE : DATA message from ASP in ASP-Down state
+ PURPOSE: To check that if DATA message is received in ASP-Down state
then it is discarded.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP1 is in Down State. Arrange the data in AS such that DATA
message with N/w Appearance A, RC P is sent to the SGP.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Down
DATA ---------------->
<--------------- Error
(Unexpected Message)
ASPUP ---------------->
Status Ind ------->
<--------------- ASP-Up-Ack
<--------------- NTFY(AS-Inactive)
TEST DESCRIPTION:
1. Send DATA message to the SGP in ASP-Down state.
2. Check A: DATA message should be discarded and an Error message
should be received at the ASP.
3. Check that state of the ASP at SGP is not disturbed.
4. Send ASPUP message on stream 0 and SGP should respond with
ASP-Up-Ack and NTFY (AS-Inactive).
Anshoo Sharma, HSS [Page 39]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Message Routing based on DPC"
+ TEST NUMBER : 2.4
+ TITLE : Message Routing
+ SUBTITLE : Message Routing towards ASP
+ PURPOSE: To check that if NIF sends a MTP-Transfer message containing
Protocol DATA to send to the AS then it is sent to the correct AS.
+ TEST CONFIGURATION: D
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
all ASP i.e. ASP1, ASP2 and ASP3 and all ASP are in Active state.
Also arrange the data in NIF at SGP such that MTP-Transfer Indication
Primitives is sent to the AS with following parameter combination:
Protocol Data and N/w Appearance A and DPC X
Protocol Data and N/w Appearance A and DPC Y
Protocol Data and N/w Appearance B and DPC T
EXPECTED MESSAGE SEQUENCE :
ASP1 ASP2 ASP3 SGP NIF
All AS are active
<---------- MTP-Transfer Req
N/w Appearance A
DPC X
<---------------------------- DATA
<---------- MTP-Transfer Req
N/w Appearance A
DPC Y
<---------------- DATA
<---------- MTP-Transfer Req
N/w Appearance B
DPC T
<-------- DATA
Anshoo Sharma, HSS [Page 40]
Internet Draft M3UA Conformance Test Plan Jan 2003
TEST DESCRIPTION:
1. Send MTP-Transfer Request Primitive from NIF in SGP containing the
Protocol Data with DPC X and N/w appearance A.
2. Check A: DATA message will be received at the ASP1.
3. Repeat the above test case for MTP-Transfer Req primitive containing
Protocol Data with DPC Y and N/w appearance A.
4. Repeat the above test case for MTP-Transfer Req primitive containing
Protocol Data with DPC T and N/w appearance B.
Anshoo Sharma, HSS [Page 41]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Message Routing based on DPC+CIC"
+ TEST NUMBER : 2.5
+ TITLE : Message Routing
+ SUBTITLE : Message Routing based on DPC+CIC
+ PURPOSE: To check that if NIF sends a MTP-Transfer message containing
Protocol DATA to send to the AS then it is sent to the correct AS.
+ TEST CONFIGURATION: E
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
all ASP i.e. ASP1 and ASP2 are in Active state. Routing
context P consists of DPC X and CIC 1 to 31. Routing context Q
consists of DPC X and CIC 33 to 63. Also arrange the data in NIF at
SGP such that MTP-Transfer Request Primitives is sent to the SGP
with the following parameter combination:
Protocol Data with DPC X and CIC 3
Protocol Data with DPC X and CIC 35
EXPECTED MESSAGE SEQUENCE :
ASP1 ASP2 SGP NIF
All AS are active
<---------- MTP-Transfer Ind
DPC X CIC 3
<---------------------------- DATA
<---------- MTP-Transfer Ind
DPC X CIC 35
<---------------- DATA
TEST DESCRIPTION:
1. Send MTP-Transfer indication Primitive from NIF in the SGP
containing the Protocol Data with DPC X and CIC value 3.
2. Check A: DATA message will be received at the ASP1.
3. Repeat the above test case for MTP-Transfer Req primitive containing
Protocol Data with DPC X and CIC value 35. DATA message should be
received at ASP2
Anshoo Sharma, HSS [Page 42]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Message Routing based on DPC+SSN"
+ TEST NUMBER : 2.6
+ TITLE : Message Routing
+ SUBTITLE : Message Routing based on DPC+SSN
+ PURPOSE: To check that if NIF sends a MTP-Transfer message containing
Protocol DATA to send to the AS then it is sent to the correct AS.
+ TEST CONFIGURATION: E
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
all ASP i.e. ASP1 and ASP2 are in Active state. Routing
context P consists of DPC X and SSN S. Routing context Q consists of
DPC X and SSN T. Also arrange data in NIF at SGP such that
MTP-Transfer Request Primitives is sent to the SGP with the
following parameter combination:
Protocol Data with DPC X and SSN S
Protocol Data with DPC X and SSN T
EXPECTED MESSAGE SEQUENCE :
ASP1 ASP2 SGP NIF
All AS are active
<---------- MTP-Transfer Req
DPC X SSN S
<---------------------------- DATA
<---------- MTP-Transfer Req
DPC X SSN T
<---------------- DATA
TEST DESCRIPTION:
1. Send MTP-Transfer Request Primitive from NIF in the SGP containing
the Protocol Data with DPC X and SSN value S.
2. Check A: DATA message will be received at the AS1.
3. Repeat the above test case for MTP-Transfer Req primitive containing
Protocol Data with DPC X and SSN value T. DATA message should be
received at AS2
Anshoo Sharma, HSS [Page 43]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Message Routing based on DPC+SIO"
+ TEST NUMBER : 2.7
+ TITLE : Message Routing
+ SUBTITLE : Message Routing based on DPC+SIO
+ PURPOSE: To check that if NIF sends a MTP-Transfer message containing
Protocol DATA to send to the AS then it is sent to the correct AS.
+ TEST CONFIGURATION: E
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
all ASP i.e. ASP1 and ASP2 are in Active state. Routing Context P
consists of DPC X and SIO S. Routing context Q consists of
DPC X and SIO T. Also arrange the data in NIF at SGP such that
MTP-Transfer Request Primitives is sent to the AS with the
following parameter combination:
Protocol Data with DPC X and SIO S
Protocol Data with DPC X and SIO T
EXPECTED MESSAGE SEQUENCE :
ASP1 ASP2 SGP NIF
All AS are active
<---------- MTP-Transfer Req
DPC X SIO S
<---------------------------- DATA
<---------- MTP-Transfer Req
DPC X SIO T
<---------------- DATA
TEST DESCRIPTION:
1. Send MTP-Transfer Request Primitive from NIF in the SGP containing
the Protocol Data with DPC X and SIO value S.
2. Check A: DATA message will be received at the AS1.
3. Repeat the above test case for MTP-Transfer Req primitive containing
Protocol Data with DPC X and SIO value T. DATA message should be
received at ASP2
Anshoo Sharma, HSS [Page 44]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Routing for Data not matching any routing context"
+ TEST NUMBER : 2.8
+ TITLE : Message Routing
+ SUBTITLE : Routing for Data not matching any routing context
+ PURPOSE: To check that if NIF sends a MTP-Transfer message containing
Protocol DATA which does not match to any routing context then
default routing is given to this message.
+ TEST CONFIGURATION: E
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1 and ASP2 and ASP and ASP2 are Active. Routing context P consists
of DPC X and SSN S. Routing context Q consists of DPC X and SSN T.
Also arrange the data in NIF at SGP such that MTP-Transfer Request
Primitives is sent to the SGP with DPC X and SSN other than S or T.
EXPECTED MESSAGE SEQUENCE :
ASP SGP NIF + SM
AS is Active
<----------- MTP-Transfer Req
DPC X & SSN <> S or T
Failure Ind. ---------->
TEST DESCRIPTION:
1. Send MTP-Transfer Request Primitive from NIF in the SGP containing
the Protocol Data having DPC and SSN such that they don't match any
routing key.
2. Check A: Failure should be returned or some default routing will be
given to this message.
3. Repeat the above test case if routing context is defined based on
DPC+CIC. Send MTP-Transfer Req from NIF containing protocol data
with DPC+CIC that doesn't match any routing key. Response will
be same as in the above case.
4. Repeat the above test case if routing context is defined based on
DPC+SIO. Send MTP-Transfer Req from NIF containing protocol data
with DPC+SIO that doesn't match this routing key. Response
will be same as in the above case.
5. Repeat the above test case if routing context is defined based on
DPC. Send MTP-Transfer Req from NIF containing protocol data with
Anshoo Sharma, HSS [Page 45]
Internet Draft M3UA Conformance Test Plan Jan 2003
DPC that doesn't match this routing key. Response will be same as
in the above case.
Note: Implementation may provide a default AS for all Data. In this
case Failure would not be returned.
Anshoo Sharma, HSS [Page 46]
Internet Draft M3UA Conformance Test Plan Jan 2003
4.3 SSNM
Test Cases to test SSNM Procedures.
"Received DAUD Message "
+ TEST NUMBER : 3.1
+ TITLE : Status Audit
+ SUBTITLE : Received DAUD message
+ PURPOSE: To check that if DAUD message is received from ASP then SGP
sends Status Request primitive to the NIF and state of ASP is not
changed at SGP.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP1 is active. Also arrange the data in ASP such that DAUD
message is sent to the SGP with Network Appearance A and Affected DPC
any value.
EXPECTED MESSAGE SEQUENCE :
ASP SGP NIF + SM
AS is active
DAUD ------------->
Status Request ------>
<------ Pause/Resume/State
<------------ DUNA/DAVA/DRST/SCON
TEST DESCRIPTION:
1. Send DAUD message with N/w appearance A and affected DPC any value
from ASP to the SGP.
2. Check A: Status Request Primitive is received at SM with the DPC and
N/w appearance received in the DAUD message.
3. Check B: State of AS will not be changed at SGP. Send Pause/Resume
primitive with N/w appearance A and SGP should send DUNA/DRST/DAVA
message to the ASP1.
4. Repeat the above test case if DAUD message is sent without N/w
Appearance parameter. Response should be same as in the above case.
Note: DUNA/DAVA/SCON message may be sent by M3UA itself in response to
DAUD message depending upon the implementation.
Anshoo Sharma, HSS [Page 47]
Internet Draft M3UA Conformance Test Plan Jan 2003
Note1: ASP auditing is an optional procedure and may not be supported
at ASP/SGP.
Anshoo Sharma, HSS [Page 48]
Internet Draft M3UA Conformance Test Plan Jan 2003
"MTP-Pause Indication Primitive:"
+ TEST NUMBER : 3.2
+ TITLE : MTP3 management
+ SUBTITLE : MTP-Pause Indication Primitive
+ PURPOSE: To check that if MTP-Pause indication primitive is received
from NIF at SGP then SGP sends DUNA message to the concerned ASPs.
+ TEST CONFIGURATION: D
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1, ASP2 and ASP3. All AS are in AS-Active state. AS1 and AS2 are
handling traffic for N/w appearance A and AS3 is handling traffic for
N/w Appearance B. Also arrange the data in NIF at SGP such that
MTP-Pause Indication Primitive is sent to the AS with Network
Appearance A and B and affected DPC any value.
EXPECTED MESSAGE SEQUENCE :
AS1 AS2 AS3 SGP NIF
All AS are active
<---------- MTP-Pause
N/w Appearance A
Affected DPC M
<---------------------------- DUNA
<----------------- DUNA
<---------- MTP-Pause
N/w Appearance B
Affected DPC M
<--------- DUNA
TEST DESCRIPTION:
1. Send MTP-Pause indication Primitive message from NIF in the SGP
containing the Network Appearance A and Affected DPC M.
2. Check A: DUNA message will be received at the ASP1 and ASP2
containing the network Appearance A and Affected DPC M.
3. Check B: DUNA message is received at both AS AS1 and AS2 which are
handling traffic for the same network appearance.
4. Check C: DUNA message is received on the Stream number 0.
5. Repeat the above test case with N/w Appearance B. In this case DUNA
message should be sent to AS3.
Anshoo Sharma, HSS [Page 49]
Internet Draft M3UA Conformance Test Plan Jan 2003
"MTP-Resume Indication Primitive"
+ TEST NUMBER : 3.3
+ TITLE : MTP3 management
+ SUBTITLE : MTP-Resume Indication Primitive
+ PURPOSE: To check that if MTP-Resume indication primitive is received
from NIF at SGP then SGP sends DAVA message to the concerned ASPs.
+ TEST CONFIGURATION: D
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1, ASP2 and ASP3. All AS are in AS-Active state. AS1 and AS2 are
handling traffic for N/w appearance A and AS3 is handling traffic for
N/w Appearance B. Also arrange the data in NIF at SGP such that
MTP-Resume Indication Primitive is sent to the AS with Network
Appearance A and B and affected DPC any value.
EXPECTED MESSAGE SEQUENCE :
AS1 AS2 AS3 SGP NIF
All AS are active
<---------- MTP-Resume
N/w Appearance A
Affected DPC M
<---------------------------- DAVA
<----------------- DAVA
<---------- MTP-Resume
N/w Appearance B
Affected DPC M
<--------- DAVA
TEST DESCRIPTION:
1. Send MTP-Resume indication Primitive from NIF in the SGP containing
the Network Appearance A and Affected DPC M.
2. Check A: DAVA message is received at AS1 and AS2 containing the
network Appearance A and Affected DPC M.
3. Check B: DAVA message is received at AS1 and AS2
4. Check C: DAVA message is received on the Stream number 0.
5. Repeat the test case for N/w appearance B and affected destination
any value. Check that message is being sent to AS3.
Anshoo Sharma, HSS [Page 50]
Internet Draft M3UA Conformance Test Plan Jan 2003
"MTP-Status Indication Primitive with Route Congested"
+ TEST NUMBER : 3.4
+ TITLE : MTP3 management
+ SUBTITLE : MTP-Status Indication Primitive with Route Congested
+ PURPOSE: To check that if MTP-Status indication primitive with Route
Congested parameter is received from NIF at SGP then SGP sends SCON
message to the concerned ASPs. Also arrange the data in NIF at SGP
such that MTP-Status indication Primitive is sent to the SGP with
cause Routing Congested, affected DPC, Congestion level and
Network Appearance.
+ TEST CONFIGURATION: D
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1, ASP2 and ASP3. All AS are in AS-Active state. AS1 and AS2 are
handling traffic for N/w appearance A and AS3 is handling traffic for
N/w Appearance B.
EXPECTED MESSAGE SEQUENCE :
AS1 AS2 AS3 SGP NIF
All AS are active
<---------- MTP-Status
N/w Appearance A
DPC M Cong Level 2
<---------------------------- SCON
<----------------- SCON
<---------- MTP-Status
N/w Appearance B
DPC M Cong Level 2
<--------- SCON
TEST DESCRIPTION:
Anshoo Sharma, HSS [Page 51]
Internet Draft M3UA Conformance Test Plan Jan 2003
1. Send MTP-Status indication Primitive from NIF in the SGP containing
the Network Appearance A, cause Route congestion, Affected DPC M and
congestion Level 2.
2. Check A: SCON message is received at the AS1 and AS2 containing the
network Appearance A, Affected DPC M, Congestion Level 2 passed to
it from NIF.
3. Check B: SCON message is received at AS1 and AS2.
4. Check C: SCON message is received on the Stream number 0.
5. Repeat the above test case for all congestion level 0, 1, 2 and 3.
SCON message will be received with congestion level passed from NIF.
6. Repeat the above test case with different congestion level for
different affected DPC. SCON message should contain the correct
congestion level for each affected destination.
7. Repeat the above test case with N/w appearance B. SCON message will
be received at AS3.
Anshoo Sharma, HSS [Page 52]
Internet Draft M3UA Conformance Test Plan Jan 2003
"MTP-Status Indication Primitive with User Part Unavailable"
+ TEST NUMBER : 3.5
+ TITLE : MTP3 management
+ SUBTITLE : MTP-Status Indication Primitive with User Part Unavailable
+ PURPOSE: To check that if MTP-Status indication primitive with cause
User Part Unavailable is received from NIF at SGP then SGP sends DUPU
message to the concerned ASPs.
+ TEST CONFIGURATION: D
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1, ASP2 and ASP3. All AS are in AS-Active state. AS1 and AS2 are
handling traffic for N/w appearance A and AS3 is handling traffic for
N/w Appearance B. Also arrange the data in NIF at SGP such that
MTP-Status indication Primitive is sent to the SGP with cause User
Part Unavailable Unknown, affected DPC, SIO for ISUP and network
appearance A. Assume routing context is DPC+SIO based.
EXPECTED MESSAGE SEQUENCE :
AS1 AS2 AS3 SGP NIF
All AS are active
<---------- MTP-Status
N/w Appearance A
DPC S
<---------------------------- DUPU
<----------------- DUPU
<---------- MTP-Status
N/w Appearance B
DPC S
<--------- DUPU
Anshoo Sharma, HSS [Page 53]
Internet Draft M3UA Conformance Test Plan Jan 2003
TEST DESCRIPTION:
1. Send MTP-Status indication Primitive from NIF in the SGP containing
the Network Appearance A, cause User Part Unavailable, Affected DPC
S and SIO for ISUP.
2. Check A: SGP will send DUPU message containing the network
Appearance A, Affected DPC S, cause unknown and user ISUP.
3. Check B: DUPU message is received at AS1 and AS2.
4. Check C: DUPU message is received on the Stream number 0.
5. Repeat the above test case with cause values Unequipped Remote User
and Inaccessible Remote User and other parameters being the same as
in the above tests. DUPU message will be received with these cause
values.
6. Repeat the above test case with SIO values TUP, Broadband ISUP,
Satellite ISUP and Reserved.
7. Repeat the above test case if MTP-Status is sent with N/w appearance
B. DUPU message will be sent to AS3.
Anshoo Sharma, HSS [Page 54]
Internet Draft M3UA Conformance Test Plan Jan 2003
"MTP-Pause Indication Primitive"
+ TEST NUMBER : 3.6
+ TITLE : MTP3 management
+ SUBTITLE : MTP-Status Indication Primitive with Route Restricted
+ PURPOSE: To check that if MTP-Status indication primitive with Route
Restricted is received from NIF at SGP then SGP sends DRST message
to the concerned ASPs.
+ TEST CONFIGURATION: D
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1, ASP2 and ASP3. All AS are in AS-Active state. AS1 and AS2 are
handling traffic for N/w appearance A and AS3 is handling traffic for
N/w Appearance B. Also arrange the data in NIF at SGP such that
MTP-Status Indication Primitive is sent to the AS with Network
Appearance A and B and affected DPC any value.
EXPECTED MESSAGE SEQUENCE :
AS1 AS2 AS3 SGP NIF
All AS are active
<---------- MTP-Status
N/w Appearance A
Cause Restricted
<---------------------------- DRST
<----------------- DRST
<---------- MTP-Status
N/w Appearance B
Cause Restricted
<--------- DRST
TEST DESCRIPTION:
1. Send MTP-Pause indication Primitive message from NIF in the SGP
containing the Network Appearance A and Affected DPC M.
2. Check A: DRST message will be received at the ASP1 and ASP2
containing the network Appearance A and Affected DPC M.
3. Check B: DRST message is received at both AS AS1 and AS2 which are
handling traffic for the same network appearance.
4. Check C: DRST message is received on the Stream number 0.
5. Repeat the above test case with N/w Appearance B. In this case DRST
message should be sent to AS3.
Anshoo Sharma, HSS [Page 55]
Internet Draft M3UA Conformance Test Plan Jan 2003
4.4 ASPSM
Test Cases to test ASPSM Procedures.
"Heartbeat and Heartbeat Ack"
+ TEST NUMBER : 4.1
+ TITLE : AS management
+ SUBTITLE : Heartbeat
+ PURPOSE: : To check that an ASP sends Heartbeat messages (to ensure
that the M3UA peers are still available to each other) and receives a
Heartbeat Ack from the remote peer.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is active. Also arrange the data in ASP such that BEAT
message is sent from ASP1 to SGP.
EXPECTED MESSAGE SEQUENCE:
ASP SGP SM
ASP is Active
a) BEAT (ASP1) ----------------->
Timer 2*T(beat) |
is started |
<---------------- BEAT ACK
b) BEAT (ASP1) ----------------->
Timer 2*T(beat) |
is started |
|
Timer 2*T(beat) is expired without any BEAT ACK is from SGP.
TEST DESCRIPTION:
1. Send BEAT Message from ASP to the SGP.
2. The beat message should be acknowledge by BEAT ACK before the Timer
expires.
3. Send the Beat message again.
Anshoo Sharma, HSS [Page 56]
Internet Draft M3UA Conformance Test Plan Jan 2003
4. The timer expires and no beat Ack message is received, the ASP will
consider remote M3UA peer as Down. Transmission of BEAT message is
stopped and ASP-Up procedures are used to re-establish communication
with the SGP M3UA peer.
5. Repeat the Test when the BEAT message is sent by SGP.
Anshoo Sharma, HSS [Page 57]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASPUP message in AS-Inactive state"
+ TEST NUMBER : 4.2
+ TITLE : Duplicate Message Handling
+ SUBTITLE : ASPUP message in ASP Inactive state
+ PURPOSE: To check that if ASPUP message is received in ASP-Inactive
state then message with ASP-Up-Ack is sent to the AS.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is in ASP-Down state. Arrange the data in ASP such that
ASPUP message is sent to the SGP two times on stream 0.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
AS is Down
ASPUP ---------------->
Status Ind ------->
<--------------- ASP-Up-Ack
<--------------- NTFY(AS-Inactive)
ASPUP ---------------->
<--------------- ASP-Up-Ack
ASPAC ---------------->
Status Ind ------->
<--------------- ASP-Active-Ack
<--------------- NTFY(AS-Active)
TEST DESCRIPTION:
1. Send ASPUP message to the SGP in ASP-Down state. ASP-Up-Ack and
NTFY (AS-Inactive) messages will come from the SGP. Send ASPUP
message again from the AS for the same ASP.
2. Check A: ASP-Up-Ack message should be received at AS.
3. Check B: State of ASP at SGP is not disturbed i.e. ASP remains in
the Inactive state. Send ASPAC message with valid Type and Routing
Context for the ASP1 and ASP-Active-Ack message should come.
Anshoo Sharma, HSS [Page 58]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASPDN message in ASP-Down state"
+ TEST NUMBER : 4.3
+ TITLE : Duplicate Message Handling
+ SUBTITLE : ASPDN message in ASP-Down state
+ PURPOSE: To check that if ASPDN message is received in ASP-Down state
then ASP-Down-Ack message is sent to the AS.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and AS is in AS-Inactive state i.e. ASP1 is Inactive. Arrange the
data in AS such that ASPDN message is sent to the SGP two times on
stream 0.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
AS is Inactive
ASPDN ---------------->
Status Ind ------->
<--------------- ASP-Down-Ack
ASPDN ---------------->
<--------------- ASP-Down-Ack
ASPUP ---------------->
Status Ind ------->
<--------------- ASP-Up-Ack
<--------------- NTFY(AS-Inactive)
TEST DESCRIPTION:
1. Send ASPDN message to the SGP in ASP-Inactive state. ASP-Down-Ack
message will be received from the SGP. Send ASPDN message
again from the ASP.
2. Check A: ASP-Down-Ack message should be received at AS.
3. Check B: State of ASP at SGP is not disturbed i.e. ASP remains in
the Down state. Send ASPUP message for the ASP,ASP-Up-Ack and NTFY
with status AS-Inactive should come.
Anshoo Sharma, HSS [Page 59]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASPUP message in ASP-Active state"
+ TEST NUMBER : 4.4
+ TITLE : Invalid Message Handling
+ SUBTITLE : ASPUP message in ASP-Active state
+ PURPOSE: To check that if ASPUP message is received in ASP-Active
state then ACK message is sent to AS and ASP
state is moved to ASP-Inactive.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP1 is Active. Arrange the data in AS such that ASPUP
message is sent to the SGP on stream 0.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Active
ASPUP ---------------->
<--------------- ASP-Up-Ack
Status Ind -------> AS Inactive
<--------------- Error
(Unexpected Message)
ASPAC ---------------->
Status Ind ------->
<--------------- ASP-Active-Ack
TEST DESCRIPTION:
1. Send ASPUP message to the SGP in ASP-Active state.
2. Check A: An Error message with parameter Unexpected Message should
be received at ASP.
3. Check B: State of ASP should not change to ASP Inactive. Send ASPAC
message with correct Type (Type is same as defined at SGP for the
AS) and routing context P to the SGP and SGP should send
ASP-Active-Ack.
Anshoo Sharma, HSS [Page 60]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASPDN message in ASP-Active state"
+ TEST NUMBER : 4.5
+ TITLE : Different Message Handling
+ SUBTITLE : ASPDN message in ASP-Active state
+ PURPOSE: To check that if ASPDN message is received in ASP-Active
state then ASP-Down-Ack message is sent to AS and State
of ASP at SGP becomes ASP-Down.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is Active. Arrange the data in ASP such that ASPDN
Message is sent to the SGP on stream 0.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Active
ASPDN ---------------->
Status Ind ------->
<--------------- ASP-Down-Ack
|
| [T(r) Expiry]
--- Status Ind -------> AS Down
ASPUP ---------------->
Status Ind ------->
<--------------- ASP-Up-Ack
<--------------- NTFY(AS-Inactive)
TEST DESCRIPTION:
1. Send ASPDN message to the SGP in ASP-Active state.
2. Check A: ASP-Down-Ack message is received at ASP.
3. Check B: State of ASP should become Down.
4. Send ASPUP message to the SGP and SGP should send ASP-Up-Ack and
NTFY message with Status ASP-Inactive.
Anshoo Sharma, HSS [Page 61]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASPM message when SGP has locked out the ASP for management reason"
+ TEST NUMBER : 4.6
+ TITLE : AS management
+ SUBTITLE : ASPM message when SGP has locked out the ASP for
management reason
+ PURPOSE: To check that if ASPM message is received when SGP has
locked out the ASP for management then ERROR message with reason
Management Blocking is sent to ASP.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP may be in any state. Arrange the data in SGP such that
ASP is locked out at the SGP. Arrange the data in AS such that ASPUP
message with valid parameters is sent to the SGP on stream 0.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
<---------- Lock-ASP
ASPUP ---------------->
<--------------- ERROR (Refused - Management Blocking)
TEST DESCRIPTION:
1. Lock out the ASP at the SGP by sending primitive for locking ASP
from SM.
2. Now send ASPUP message with valid parameters from ASP to SGP.
2. Check A: Error message with reason " Management Blocking"
is received at ASP.
3. Repeat the above test case for ASPAC message from ASP to the SGP
with valid parameters. Response should be same.
Anshoo Sharma, HSS [Page 62]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASP ID in ASP UP Message"
+ TEST NUMBER : 4.7
+ TITLE : ASP management
+ SUBTITLE : ASPUP Message from a ASP with unconfigured Transport
Address.
+ PURPOSE: To test that on when an ASP sends an ASPUP message with
ASP ID from a new Transport Address then the SGP updates the
Transport Address for this ASP with the new Transport Address.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is in ASP-Down state. The Transport Address statically
configured for the ASP is T1 and the SCTP association is with
Transport Address T2. The ASP is statically configured to have ASP ID
'I'.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
(From Transport Addr T2)
ASPUP ---------------->
(ASP ID 'I')
<--------------- ASPUP-Ack
<--------------- NTFY
Status Ind ------>
TEST DESCRIPTION:
1. Send ASPUP from ASP (at Transport Address T2) to SGP with ASP ID
'I'.
2. Check A: SGP updates the Transport Address for ASP (with ASP ID 'I')
to T2 which was in ASP-Down state up till now.
3. Check B: ASPUP was successfully processed at the ASP and the state
of ASP has changed to ASP-Inactive. ASPUP-Ack and NTFY messages have
been sent to ASP.
Anshoo Sharma, HSS [Page 63]
Internet Draft M3UA Conformance Test Plan Jan 2003
4.5 ASPTM
Test Cases to test ASPTM Procedures.
"Transfer Request Primitive from NIF in AS Inactive State"
+ TEST NUMBER : 5.1
+ TITLE : AS management
+ SUBTITLE : Transfer Request from NIF in AS Inactive State
+ PURPOSE: To check that if AS is Inactive at SGP and NIF sends
Transfer Primitive to send to that AS then it receives a send
failure.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is active. Also arrange the data in ASP such that ASPIA
message is sent from ASP1 to SGP . The Type field in ASPIA
can be any valid value which is equal to the traffic handling mode
for the AS at the SGP and Routing Context should be P.
EXPECTED MESSAGE SEQUENCE :
ASP SGP NIF + SM
ASP is Active
ASPIA --------------->
(ASP1) Status Ind -------->
<-------------- ASP-Inactive-Ack
<-------------- NTFY(AS-Pending)
|
|
___ [T(r) Expires]
Status Ind --------> AS Inactive
<-------- MTP-Transfer
Send failure -------->
Pause Ind -------->
Anshoo Sharma, HSS [Page 64]
Internet Draft M3UA Conformance Test Plan Jan 2003
TEST DESCRIPTION:
1. Send ASPIA Message for ASP1 from ASP to the SGP. ASP will move to
Inactive state at the SGP. Send MTP-Transfer Primitive with N/w
Appearance A containing Protocol Data with DPC X.
2. Check A: Send failure should be received at the NIF and DATA message
should not be sent to ASP. Some implementations may also indicate a
Pause Ind at the SGP for the SPMC.
3. Repeat the above test if ASPIA message is sent without Routing
Context Parameter. ASP-Inactive-Ack and NTFY(AS-Pending) should be
received at the ASP with either all routing contexts configured at
the SGP or with no routing context for the ASP.
4. Repeat the above test if instead of sending ASPIA message, SCTP
association between ASP and SGP is removed.
Note: In some implementation there may be T(r) running on receiving
ASPDN or ASPIA message for the last ASP and for that time AS will
be in AS-Pending state. In that case let the timer T(r) expire
before sending the Transfer primitive.
Anshoo Sharma, HSS [Page 65]
Internet Draft M3UA Conformance Test Plan Jan 2003
"MTP-Transfer Request Primitive from NIF in AS Down State"
+ TEST NUMBER : 5.2
+ TITLE : AS management
+ SUBTITLE : MTP-Transfer Request from NIF in AS Down State
+ PURPOSE: To check that if AS is down at SGP and NIF sends MTP-
Transfer Primitive to send to that AS then it receives a send
failure.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is active. Also arrange the data in ASP such that ASPIA and
ASPDN message is sent from ASP to SGP on stream 0.
EXPECTED MESSAGE SEQUENCE :
ASP SGP NIF + SM
ASP is Active
ASPIA --------------->
(ASP1) Status Ind --------->
<-------------- ASP-Inactive-Ack
<-------------- NTFY(AS-Pending)
T(r) Started
ASPDN --------------->
(ASP1) Status Ind --------->
<-------------- ASP-Down-Ack
|
|
--- T(r) Expiry
Status Ind (AS Down)--------->
<-------- MTP-Transfer
Send failure -------->
Pause Ind -------->
Anshoo Sharma, HSS [Page 66]
Internet Draft M3UA Conformance Test Plan Jan 2003
TEST DESCRIPTION:
1. Send ASPIA Message for ASP1 from ASP to the SGP. ASP will move to
Inactive state at the SGP.
2. Send ASPDN message from ASP to the SGP. ASP will move to down state
at the SGP.
3. After Pending Timer T(r) Expires. Send MTP-Transfer Primitive with
N/w Appearance A containing Protocol Data with DPC X.
3. Check A: Send failure should be received at the NIF and DATA message
should not be sent to ASP. Some implementations may also indicate a
Pause Ind at the SGP for the SPMC.
Note: In some implementation there may be T(r) running on receiving
ASPDN message for the last ASP and for that time AS will
be in AS-Pending state. In that case let the timer T(r) expire
before sending the MTP-Transfer primitive.
Anshoo Sharma, HSS [Page 67]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Timer T(r) Cancellation"
+ TEST NUMBER : 5.3
+ TITLE : AS management
+ SUBTITLE : Timer T(r) Cancellation
+ PURPOSE: To check that after last ASP becomes inactive then SGP
buffers the messages from NIF for time T(r) and if ASPAC comes before
its expiry then all buffered messages are sent to the ASP.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is active. Arrange the data in ASP such that ASPIA and
ASPAC messages are sent from ASP1 to SGP. The Traffic Mode
field in ASPIA and ASPAC can be any valid value and Routing Context
should be P. Let the value of Timer T(r) be z sec.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is active
ASPIA ----------------->
(ASP1) Status Ind -------->
<---------------- ASP-Inactive-Ack
<---------------- NTFY(AS-Pending)
| Timer T(r) is started
|
| Time < z sec. <------- MTP-Transfer
| Message will be buffered
| <------- MTP-Transfer
| Message will be buffered
ASPAC --------------->
(ASP1) Status Ind -------->
<--------------- ASP-Active-Ack
<--------------- NTFY(AS-Active)
<--------------- DATA
<--------------- DATA
Anshoo Sharma, HSS [Page 68]
Internet Draft M3UA Conformance Test Plan Jan 2003
TEST DESCRIPTION:
1. Send ASPIA Message from ASP1 to SGP. ASP will become Inactive at the
SGP.
2. Send MTP-Transfer Primitive from NIF with N/w Appearance A
containing Protocol Data to be sent to DPC X.
3. Check A: DATA message will not be received at ASP.
4. Send ASPAC message containing N/w Appearance A before Timer T(r)
expires.
5. Check B: DATA messages buffered at the SGP will be sent to the AS.
Note: This case is implementation specific. In some implementation
there may not be any Timer T(r) running. In that case there is no
need to run this test case.
Anshoo Sharma, HSS [Page 69]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Timer T(r) Expiry"
+ TEST NUMBER : 5.4
+ TITLE : AS management
+ SUBTITLE : Timer T(r) Expiry
+ PURPOSE: To check that if timer T(r) expires without receiving an
ASPAC Message then the AS moves into Inactive State.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is active. Arrange data in ASP such that ASPIA and ASPAC
messages are sent from ASP to SGP. The Type field in ASPIA and ASPAC
can be any valid value and Routing Context should be P.
Let the value of Timer T(r) is z sec.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is active
<------- MTP-Transfer
<--------------- DATA
<------- MTP-Transfer
<--------------- DATA
ASPIA ---------------->
Status Ind -------->
<--------------- ASP-Inactive-Ack
<--------------- NTFY(AS-Pending)
|
|Time = z sec <------- MTP-Transfer
|
| <------- MTP-Transfer
| ( Data is buffered and after expiry
| of timer it will be discarded)
--- Status Ind ---------> (AS Inactive)
Anshoo Sharma, HSS [Page 70]
Internet Draft M3UA Conformance Test Plan Jan 2003
<-------- MTP-Transfer
Send Failure ------->
TEST DESCRIPTION:
1. Send MTP-Transfer Primitive with N/w appearance A containing
protocol Data to send to DPC X. Message will be sent to ASP.
2. Send ASPIA message from ASP1 to the SGP. ASP will become Inactive at
SGP. AS will be in AS-Pending state at the SGP.
3. Check A: Timer T(r) is started.
4. Send MTP Transfer Primitive with Network Appearance A containing
protocol data to send DPC X. Message will be buffered at SGP.
5. Timer T(r) is expired, and the message buffered is discarded, also
after the expiry of T(r) AS will move to the AS-INACTIVE state.
6. Send MTP-Transfer Primitive from NIF with N/w appearance A
containing protocol Data to send to DPC X. SGP will send
Send Failure.
7. Repeat the above test case if ASPDN message is sent instead of
ASPIA message.
Note: This case is implementation specific. In some implementation
there may not be any Timer T(r) running. In that case send
failure is notified by M3UA on receiving MTP-Transfer request.
Anshoo Sharma, HSS [Page 71]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASPAC message with more than one Routing Context"
+ TEST NUMBER : 5.5
+ TITLE : AS Management
+ SUBTITLE : ASPAC message with more than one Routing Context
+ PURPOSE: To check that if ASPAC message is received with more than
one Routing Context then status of ASP is active in all the AS for
which the RC was present in the Message and are served by this ASP.
+ TEST CONFIGURATION: B
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is belonging to two AS, AS1 and AS2. AS1 is handling
traffic for routing context P and AS2 is handling traffic for routing
context Q. ASP1 is in Inactive state i.e. AS1 and AS2 are in the
AS-Inactive state at SGP. Also arrange the data in ASP1 such that
ASPAC message is sent from ASP1 to SGP containing Routing Context P
and Q. Fill any valid value in the Type parameter which
is same as configured for AS1 and AS2 at the SGP and it should be
same for both AS.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
AS1 & AS2 is Inactive
ASPAC ------------------>
Routing Context P and Q
Status Ind --------->
<----------------- ASP-Active-Ack
<----------------- NTFY (AS1 and AS2 Active)
<-------- MTP-Transfer
for Routing Context P
<----------------- DATA
<-------- MTP-Transfer
for Routing Context Q
<----------------- DATA
Anshoo Sharma, HSS [Page 72]
Internet Draft M3UA Conformance Test Plan Jan 2003
TEST DESCRIPTION:
1. Send ASPAC Message with routing contexts P and Q to the SGP.
2. Check A: ASP-Active-Ack and NTFY message with status AS-Active
should be received at ASP with routing contexts P and Q.
3. Check B: Check that state of ASP is active in AS1 and AS2. This can
be checked by sending DATA messages containing protocol DATA for
both Routing Contexts.
Anshoo Sharma, HSS [Page 73]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASPAC message without any Routing Context"
+ TEST NUMBER : 5.6
+ TITLE : AS management
+ SUBTITLE : ASPAC message without any Routing Context
+ PURPOSE: To check that if ASPAC message is received without any
Routing Context then status of ASP is active in all the AS
which this ASP serves.
+ TEST CONFIGURATION: B
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is Inactive in both the AS at the SGP. Arrange data in ASP
such that ASPAC messages is sent to the SGP from ASP.
Don't fill any routing context parameter in ASPAC.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
AS1 & AS2 is Inactive
ASPAC ------------------>
No Routing Context Status Ind --------->
<----------------- ASP-Active-Ack
<----------------- NTFY (AS Active)
TEST DESCRIPTION:
1. Send ASPAC Message without any routing to the SGP.
2. Check A: ASP-Active-Ack and NTFY message with status AS-Active
should be received at ASP.
3. Check B: Check that state of ASP is active using configuration Data
present at the SGP.
Note: If there is no Configuration Data present at the SGP and the ASP
has not dynamically registered for any Routing Context, then the
ASP Active Message is silently discarded at the SGP. No Ack or
NTFY as shown above is sent in that case.
Anshoo Sharma, HSS [Page 74]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASPIA message with more than one Routing Context"
+ TEST NUMBER : 5.7
+ TITLE : AS management
+ SUBTITLE : ASPIA message with more than one Routing Context
+ PURPOSE: To check that if ASPIA message is received with more than
one Routing Context then status of ASP is Inactive in all the AS to
which this ASP belongs.
+ TEST CONFIGURATION: B
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP1 is belonging to two AS, AS1 and AS2. AS1 is handling
traffic for routing context P and AS2 is handling traffic for routing
context Q. ASP1 is in Active state i.e. AS1 and AS2 are in the
AS-Active state at SGP. Also arrange the data in ASP1 such that ASPIA
message is sent from ASP1 to SGP containing Routing Context P and Q.
Fill any valid value in the Type parameter which is same as
configured for AS1 and AS2 in SGP and it should be same for both AS.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
AS1 & AS2 is Active
ASPIA ------------------>
Routing Context P and Q Status Ind -------->
<----------------- ASP-Inactive-Ack
<----------------- NTFY(AS-Pending)
|
|
___ [T(r) Expires]
Status Ind -------->(AS1,AS2 Inactive)
<-------- MTP-Transfer
Routing Context P
Send Failure -------->
Anshoo Sharma, HSS [Page 75]
Internet Draft M3UA Conformance Test Plan Jan 2003
<-------- MTP-Transfer
Routing Context Q
Send Failure -------->
TEST DESCRIPTION:
1. Send ASPIA Message containing routing contexts P and Q from ASP1 to
the SGP.
2. Check A: ASP-Inactive-Ack and NTFY (AS-Pending) message should be
received at the ASP with routing contexts P and Q.
3. Check B: NTFY message is received on stream 0.
4. Check C: Check that state of ASP is Inactive in AS1 and AS2. This
can be checked by sending MTP-Transfer primitive from NIF at SGP
containing protocol DATA for both Routing Contexts.
Note: Routing Context is an optional parameter in the NTFY message.
Some implementation may not send this parameter in the NTFY
message. In that case two NTFY message with status
AS-Inactive/AS-Pending will be received one for AS1 and other for
AS2.
Anshoo Sharma, HSS [Page 76]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Notify Message with AS Status is sent only for AS State change"
+ TEST NUMBER : 5.8
+ TITLE : AS management
+ SUBTITLE : Notify Message with AS Status is sent only for AS State
change
+ PURPOSE: To check that NTFY message with AS state change is not sent
if there is no change in the state of the AS.
+ TEST CONFIGURATION: C
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. Both ASP are having SCTP association with SGP and are active in
the AS. Arrange data in ASP such that ASPUP, ASPAC, ASPIA and ASPDN
messages are sent to the SGP from ASP1. Fill the routing
contexts P and Type parameter any valid value which is same
configured for AS at the SGP.
EXPECTED MESSAGE SEQUENCE :
AS SGP SM
Both ASPs are active
ASPIA(ASP1) ----------------->
<---------------- ASP-Inactive-Ack
Check: NTFY(AS-Pending) is not received
Status Ind --------->
ASPDN(ASP1) ----------------->
<---------------- ASP-Down-Ack
Check: NTFY is not received
Status Ind --------->
ASPUP(ASP1) ----------------->
<---------------- ASP-Up-Ack
Anshoo Sharma, HSS [Page 77]
Internet Draft M3UA Conformance Test Plan Jan 2003
Check: NTFY(AS-Inactive) is not received
Status Ind --------->
ASPAC(ASP1) ----------------->
<---------------- ASP-Active-Ack
Check: NTFY(AS-Active) is not received
Status Ind --------->
TEST DESCRIPTION:
1. Send ASPIA message for ASP1 from ASP to the SGP with routing context
P and Type parameter any valid value.
2. Check A: ASP-Inactive-Ack messages is received at the AS and
NTFY message with status AS-Inactive is not received.
3. Repeat the above test case for other messages like ASPDN, ASPUP and
ASPAC for ASP1 from AS to SGP.
Anshoo Sharma, HSS [Page 78]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Notify Message with AS Status is sent only for AS State change"
+ TEST NUMBER : 5.9
+ TITLE : AS management
+ SUBTITLE : Notify Message with AS Status Change
+ PURPOSE: To check that NTFY message with AS state change is sent
if AS state has changed.
+ TEST CONFIGURATION: C
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. Both ASP are having SCTP association with SGP and are active in
the AS. Arrange data in ASP such that ASPUP, ASPAC, ASPIA and ASPDN
messages are sent to the SGP from ASP1 and ASP2. Fill the
routing contexts P and Type parameter any valid value which is same
configured for AS at the SGP.
EXPECTED MESSAGE SEQUENCE :
AS SGP SM
Both ASP are active
ASPIA(ASP1) ----------------->
<---------------- ASP-Inactive-Ack
Status Ind --------->
ASPIA(ASP2) ----------------->
<---------------- ASP-Inactive-Ack
<---------------- NTFY(AS-Pending)
Status Ind --------->
ASPDN(ASP1) ----------------->
<---------------- ASP-Down-Ack
Status Ind --------->
ASPDN(ASP2) ----------------->
<---------------- ASP-Down-Ack
Anshoo Sharma, HSS [Page 79]
Internet Draft M3UA Conformance Test Plan Jan 2003
Status Ind --------->
[T(r) Expiry]
Status Ind ---------> (AS Down)
ASPUP(ASP1) ----------------->
<---------------- ASP-Up-Ack
<---------------- NTFY( AS-Inactive)
Status Ind --------->
ASPUP(ASP2) ----------------->
<---------------- ASP-Up-Ack
Status Ind --------->
ASPAC(ASP1) ----------------->
<---------------- ASP-Active-Ack
<---------------- NTFY( AS-Active)
Status Ind --------->
ASPAC(ASP2) ----------------->
<---------------- ASP-Active-Ack
Status Ind --------->
TEST DESCRIPTION:
1. Send ASPIA message from ASP1 and ASP2 to the SGP with routing
context P and Type parameter any valid value.
2. Check A: ASP-Inactive-Ack and NTFY message with status AS-Pending is
received at the AS.
3. Check B: NTFY messages are received on stream 0.
4. Repeat the above test case for other messages like ASPDN, ASPUP and
ASPAC for ASP1 from ASP to SGP.
Note: NTFY message with AS status may come before the NTFY message with
ASP status.
Anshoo Sharma, HSS [Page 80]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Invalid routing context parameter in ASPAC message"
+ TEST NUMBER : 5.10
+ TITLE : Invalid Message Handling
+ SUBTITLE : Invalid routing context Parameter in ASPAC message
+ PURPOSE: To check that if ASPAC message with Invalid routing context
parameter is received then ASPAC message is discarded and Error
message is sent to the ASP.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and AS is in AS-Inactive state i.e. ASP1 is Inactive. Arrange the
data in AS such that ASPAC message with Routing Context P is sent
to the SGP.
EXPECTED MESSAGE SEQUENCE :
ASP SGP NIF
AS is Inactive
ASPAC ---------------->
Routing context Q
<--------------- Error
(Invalid Routing Context)
ASPAC ---------------->
Routing context P and Q
<--------------- Error
(Invalid Routing Context)
<--------------- ASP-Active-Ack with routing context P
<--------------- NTFY (AS-Active)
Status Ind --------->
TEST DESCRIPTION:
1. Send ASPAC message with routing context Q.
2. Check A: SGP will send an Error message with Invalid Routing Context
Anshoo Sharma, HSS [Page 81]
Internet Draft M3UA Conformance Test Plan Jan 2003
parameter.
3. Send ASPAC message with routing context P and Q.
4. Check B: ASP-Active-Ack and NTFY (AS-Active) message will be sent
for routing context P, and ERROR would be sent for
Routing Context Q.
Note: Routing context is an optional parameter in ASPAC message. In
some implementation this field may not come in ASPAC message. In
those implementation this test case need not be run.
Anshoo Sharma, HSS [Page 82]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Invalid routing context parameter in ASPIA message"
+ TEST NUMBER : 5.11
+ TITLE : Invalid Message Handling
+ SUBTITLE : Invalid routing context Parameter in ASPIA message
+ PURPOSE: To check that if ASPIA message with Invalid routing context
parameter is received then ASPIA message is discarded.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and AS is in AS-Active state i.e. ASP1 is active. Arrange the
data in AS such that ASPIA message with Routing Context Q is sent to
the SGP.
EXPECTED MESSAGE SEQUENCE :
ASP SGP NIF
ASP is Active
ASPIA ---------------->
Routing context Q
<--------------- Error
(Invalid Routing Context)
ASPIA ---------------->
Routing context P and Q
<--------------- Error
(Invalid Routing Context)
<--------------- ASP-Inactive-Ack with routing context P
<--------------- NTFY(AS-Pending)
Status Ind --------->
TEST DESCRIPTION:
1. Send ASPIA message with Routing Context Q.
2. Check A: SGP will send an Error message with Invalid Routing Context
parameter.
Anshoo Sharma, HSS [Page 83]
Internet Draft M3UA Conformance Test Plan Jan 2003
3. Send ASPIA message with routing context P and Q.
4. Check B: ASP-Inactive-Ack and NTFY (AS-Pending) message will be sent
with status AS-Pending for routing context P and ERROR would be sent
for Routing Context Q.
Note: Routing context is an optional parameter in ASPIA message. In
some implementation this field may not come in ASPIA message. In
those implementation this test case need not be run.
Anshoo Sharma, HSS [Page 84]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASPAC message in ASP-Active state"
+ TEST NUMBER : 5.12
+ TITLE : Duplicate Message Handling
+ SUBTITLE : ASPAC message in ASP-Active state
+ PURPOSE: To check that if ASPAC message is received in ASP-Active
state then ASP-Active-Ack message is sent to the AS.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and AS is in AS-Inactive state i.e. ASP1 is Inactive. Arrange the
data in ASP such that ASPAC message with correct Type (As defined at
SGP for the AS) and routing context P is sent to the SGP.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
AS is Inactive
ASPAC ---------------->
Status Ind ------->
<--------------- ASP-Active-Ack
<--------------- NTFY (AS-Active)
ASPAC ---------------->
<--------------- ASP-Active-Ack
DATA ---------------->
MTP-Transfer Ind ------->
TEST DESCRIPTION:
1. Send ASPAC message to the SGP in ASP-Inactive state. ASP-Active-Ack
and NTFY (AS-Active) message will come from the SGP.
2. Send ASPAC message again from the AS for the same ASP.
3. Check A: ASP-Active-Ack message should be received at ASP.
4. Check B: State of ASP at SGP is not disturbed i.e. ASP remains in
the Active state. Send DATA message for the ASP and SGP should send
MTP-Transfer indication to the NIF.
Anshoo Sharma, HSS [Page 85]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASPIA message in ASP-Inactive state"
+ TEST NUMBER : 5.13
+ TITLE : Duplicate Message Handling
+ SUBTITLE : ASPIA message in ASP-Inactive state
+ PURPOSE: To check that if ASPIA message is received in ASP-Inactive
state then ASP-Inactive-Ack message is sent to the ASP.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and AS is in AS-Active state i.e. AS1 is active. Arrange the data
in AS such that ASPIA message with correct Type(Type is same as
defined at SGP for the AS) and Routing Context P is sent to the SGP.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
AS is Active
ASPIA ---------------->
Status Ind ------->
<--------------- ASP-Inactive-Ack
<--------------- NTFY(AS-Pending)
ASPIA ---------------->
<--------------- ASP-Inactive-Ack
ASPAC ---------------->
Status Ind ------->
<--------------- ASP-Active-Ack
<--------------- NTFY(AS-Active)
TEST DESCRIPTION:
1. Send ASPIA message to the SGP in ASP-Active state. ASP-Inactive-Ack
and NTFY (AS-Pending) messages will come from the SGP.
2. Send ASPIA message again from the AS for the same ASP.
3. Check A: ASP-Inactive-Ack message will come from SGP.
Anshoo Sharma, HSS [Page 86]
Internet Draft M3UA Conformance Test Plan Jan 2003
4. Check B: State of ASP at SGP is not disturbed i.e. ASP remains in
the Inactive state. Send ASPAC message with correct Type(Type is
same as defined at SGP for the AS) for the ASP1 and SGP should
respond with ASP-Active-Ack message.
Anshoo Sharma, HSS [Page 87]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Loadshare Mode of Traffic handling in ASPAC message"
+ TEST NUMBER : 5.14
+ TITLE : Mode of Traffic Handling by ASP in ASPAC message
+ SUBTITLE : Loadshare mode of Traffic Handling
+ PURPOSE: To check that if an ASPAC message is received with Type
field containing Loadshare mode then traffic is distributed between
this ASP and all other active ASPs.
+ TEST CONFIGURATION: C
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1 and ASP2. ASP1 is active. Arrange the DATA in AS such that it
sends ASPAC message for ASP2 with Loadshare mode and routing context
P. Also mode of traffic handling for AS at SGP is Loadshare.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP1 is Active
ASPAC(ASP2) ---------------->
Loadshare Mode Status Ind ------->
<--------------- ASP-Active-Ack
<----------- MTP-Transfer Req
DPC X & CIC S
To ASP1 <--------------- DATA
<----------- MTP-Transfer Req
DPC X & CIC T
To ASP2 <--------------- DATA
ASPIA(ASP1) ---------------->
Status Ind ------->
<--------------- ASP-Inactive-Ack
<----------- MTP-Transfer Req
DPC X & CIC S
Anshoo Sharma, HSS [Page 88]
Internet Draft M3UA Conformance Test Plan Jan 2003
To ASP2 <--------------- DATA
<----------- MTP-Transfer Req
DPC X & CIC T
To ASP2 <--------------- DATA
TEST DESCRIPTION:
1. Send ASPAC message with Loadshare mode in type field and Routing
context P from AS to SGP for ASP2.
2. Check A: ASP-Active-Ack message should be received at AS.
3. Check B: Traffic should also go ASP2 which has sent the ASPAC. Check
this by sending MTP-Transfer Req from NIF at SGP containing
different CIC values assuming traffic is load shared based on the
CIC.
4. Send ASPIA message from ASP1 to the SGP.
5. ASP1 will receive ASP-Inactive-Ack from SGP.
6. Check that all the traffic is now going to ASP2.
Note: An implementation can choose to do the loadsharing on the basis
of CIC or SLS.
Anshoo Sharma, HSS [Page 89]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Loadshare Mode of Traffic handling by ASP in ASPIA message"
+ TEST NUMBER : 5.15
+ TITLE : Mode of Traffic Handling
+ SUBTITLE : Loadshare mode of Traffic Handling by ASP in ASPIA
message.
+ PURPOSE: To check that if an ASPIA message is received with Type
field containing Loadshare mode and no other active ASPs are
available then a NTFY (Insufficient ASPs) is sent to all
inactive ASPs.
+ TEST CONFIGURATION: C
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1, ASP2 and ASP3. ASP1 and ASP2 are active and ASP3 is Inactive
and all are in Loadshare mode of traffic handling. Arrange the DATA
in ASP2 such that it sends ASPIA message for ASP2 and routing
context P. Also mode of traffic handling for AS at SGP is Loadshare.
AS is configured at SGP such that a minimum of 2 ASPs are required
for handling the traffic for routing context P.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP1 & ASP2 are Active
ASPIA(ASP2) ---------------->
Loadshare Mode
To ASP3 <--------------- ASP-Inactive-Ack
Status Ind ------->
To ASP3 <--------------- NTFY (Insufficient ASPs)
with routing context P
<------- Transfer Req
To ASP1 <--------------- DATA
TEST DESCRIPTION:
Anshoo Sharma, HSS [Page 90]
Internet Draft M3UA Conformance Test Plan Jan 2003
1. Send ASPIA message with Loadshare mode in type field and Routing
context P from ASP2 to SGP.
2. Check A: ASP-Inactive-Ack message should be received at ASP2.
4. Check B: NTFY (Insufficient ASPs) should be received at ASP2 and
ASP3.
4. Check C: All the traffic is now going to ASP1.
Anshoo Sharma, HSS [Page 91]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Over-ride Mode of Traffic handling"
+ TEST NUMBER : 5.16
+ TITLE : Mode of Traffic Handling by ASP in ASPAC message
+ SUBTITLE : To check if ASP receives data during Over-ride mode of
Traffic Handling changeover.
+ PURPOSE: To check that if an ASP receives data during the changeover
of ASPs in Override mode of traffic handling.
+ TEST CONFIGURATION: C
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP1 in AS is active. Arrange the data in ASP such that it sends
ASPAC message with over-ride mode and routing context P for ASP2
and ASP1 receives the DATA before it receives NTFY message.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP1 is Active
ASPAC(ASP2) ---------------->
Override Mode Status Ind ------->
DATA ----------------> (Data is buffered and will
(From ASP1) be passed on when ASP2
becomes active.)
To ASP2 <--------------- ASP-Active-Ack
To ASP1 <--------------- NTFY(Alternate ASP-Active)
DATA ----------->
DATA ---------------->
(From ASP2) DATA ----------->
TEST DESCRIPTION:
1. Send ASPAC message with override mode in type field and Routing
context P from AS to SGP for ASP2.
2. Send DATA from ASP1 to SGP before receiving NTFY message.
3. Check A: The data is buffered at SGP.
4. ASP2 receives ASP-Active-Ack and ASP1 receives a NTFY message with
status as Alternate ASP Active.
5. Check B: The data buffered at SGP is passed further. And now it will
receive data from ASP2.
Anshoo Sharma, HSS [Page 92]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Over-ride Mode of Traffic handling"
+ TEST NUMBER : 5.17
+ TITLE : Mode of Traffic Handling by ASP in ASPAC message
+ SUBTITLE : No NTFY message to the ASP whose status is not changed in
Over-ride mode of Traffic Handling
+ PURPOSE: To check that if an ASPAC message is received with Type
field containing over-ride mode then NTFY Alternate ASP Active is
send to that ASP only whose traffic is going to be handled by the
sending ASP. All traffic is sent to that ASP which sent ASPAC
message.
+ TEST CONFIGURATION: D
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP1 and ASP2 are active and handling the traffic for routing
context P and Q, ASP3 is Inactive. Now arrange Data at ASP3 for ASPAC
with traffic handling mode as override for routing context P. Also
the mode of traffic handling for all AS at SGP is also override mode.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP1 and ASP2 are Active
<----------- MTP-Transfer Req
Routing Context P
To ASP1 <--------------- DATA
<----------- MTP-Transfer Req
Routing Context Q
To ASP2 <--------------- DATA
ASPAC(ASP3) ---------------->
Routing Context P
Override Mode Status Ind ------->
To ASP3 <--------------- ASP-Active-Ack
To ASP1 <--------------- NTFY(Alternate ASP-Active)
<----------- MTP-Transfer Req
Routing Context P
Anshoo Sharma, HSS [Page 93]
Internet Draft M3UA Conformance Test Plan Jan 2003
To ASP3 <--------------- DATA
<----------- MTP-Transfer Req
Routing Context Q
To ASP2 <--------------- DATA
TEST DESCRIPTION:
1. Send data with routing context as P and Q to ASP, ASP1 and ASP2 will
receive the data respectively.
2. Send ASPAC for ASP3 with routing context P and traffic handling mode
as override.
3. Check A: ASP3 will receive ASP Active Ack and NTFY message with
status Alternate ASP-Active should be received by ASP1.
3. Send data with routing context as P and Q to ASP, ASP3 and ASP2 will
receive the data respectively.
4. Check B: NTFY message with status Alternate ASP-Active is not
received by ASP2.
Anshoo Sharma, HSS [Page 94]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Loadshare Mode of Traffic handling in ASPIA message"
+ TEST NUMBER : 5.18
+ TITLE : Mode of Traffic Handling by ASP in ASPIA message
+ SUBTITLE : Loadshare mode of Traffic Handling
+ PURPOSE: To check that if an ASPIA message is received with Type
field containing Loadshare mode then all traffic is sent to other
ASP.
+ TEST CONFIGURATION: C
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1 and ASP2. ASP1 and ASP2 in AS are active and are in Loadshare
mode of traffic handling. Arrange the DATA in AS such that it sends
ASPIA message with Loadshare mode and routing context P for ASP1.
Also mode of traffic handling for AS at SGP is Loadshare.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP1 & ASP2 are Active
ASPIA(ASP2) ---------------->
(Mode = Loadshare) Status Ind ------->
To ASP2 <--------------- ASP-Inactive-Ack
<----------- MTP-Transfer Req
DPC X & CIC S
To ASP1 <--------------- DATA
<----------- MTP-Transfer Req
DPC X & CIC T
To ASP1 <--------------- DATA
TEST DESCRIPTION:
1. Send ASPIA message with Loadshare mode in type field and Routing
context P from ASP1 to SGP.
2. Check A: SGP should send ASP-Inactive-Ack message.
3. Check B: All traffic should go to ASP1. Check this by sending
MTP-Transfer Req from NIF at SGP with Protocol Data containing
different SLS values.
Anshoo Sharma, HSS [Page 95]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Last ASP in a SPMC becomes Inactive"
+ TEST NUMBER : 5.19
+ TITLE : SPMC Management
+ SUBTITLE : Last ASP in a SPMC goes down
+ PURPOSE: To check that if last ASP in a SPMC becomes inactive then
SGP gives NIF the MTP-Pause indication.
+ TEST CONFIGURATION: C
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1 and ASP2. ASP1 and ASP2 in AS are active. Arrange the DATA in
ASP such that ASPIA message is sent from ASP to SGP for ASP1 and
ASP2.
EXPECTED MESSAGE SEQUENCE :
AS SGP SM + NIF
ASP1 & ASP2 are Active
ASPIA(ASP1) ---------------->
Status Ind ------->
To ASP1 <--------------- ASP-Inactive-Ack
ASPIA(ASP2) ---------------->
Status Ind ------->
To ASP2 <--------------- ASP-Inactive-Ack
To ASP1 <--------------- NTFY(AS-Pending)
To ASP2 <--------------- NTFY(AS-Pending)
|
| [ T(r) Expires]
--- Status Ind -------> AS Inactive
SPMC Status Ind -------->
Anshoo Sharma, HSS [Page 96]
Internet Draft M3UA Conformance Test Plan Jan 2003
TEST DESCRIPTION:
1. Send ASPIA and message for ASP1 and ASP2 from AS to SGP.
2. ASP Inactive Ack and NTFY (AS-Pending) messages are received at AS.
3. Check A: SGP should send MTP-Pause indication to the NIF when last
ASP goes down.
4. Repeat the above test case if SGP and ASP are having the same point
code.
Anshoo Sharma, HSS [Page 97]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Last ASP serving a specific DPC+SIO becomes Inactive "
+ TEST NUMBER : 5.20
+ TITLE : SPMC Management
+ SUBTITLE : Last ASP serving a specific DPC+SIO becomes Inactive
+ PURPOSE: To check that if last ASP which is serving a specific
DPC + SIO goes down then SGP gives NIF the Status indication with
user part unavailable.
+ TEST CONFIGURATION: E
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1, ASP2 and ASP3. All ASP are active. Arrange the DATA in AS1 and
AS2 such that if ASPIA message are sent from ASP to SGP for ASP1 and
ASP2.
EXPECTED MESSAGE SEQUENCE :
AS SGP SM + NIF
ASP1 & ASP2 are Active
ASPIA(ASP1) ---------------->
Status Ind ------->
To ASP1 <--------------- ASP-Inactive-Ack
ASPIA(ASP2) ---------------->
Status Ind ------->
To ASP2 <--------------- ASP-Inactive-Ack
To ASP1 <--------------- NTFY(AS-Pending)
and ASP2
Status Ind -------->
(user part unavailable)
TEST DESCRIPTION:
1. Send ASPIA and ASPDN messages for ASP1 and ASP2 from AS to SGP.
2. Check A: SGP should send Status indication to the NIF when last ASP
goes down.
3. Repeat the above test case if ASP2 goes down.
Anshoo Sharma, HSS [Page 98]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Broadcast Mode of Traffic Handling"
+ TEST NUMBER : 5.21
+ TITLE : Broadcast Mode of Traffic Handling
+ SUBTITLE : Broadcast mode of Traffic Handling
+ PURPOSE: To check that if the AS is in Broadcast Mode then the
DATA is sent to all Active ASPs in the AS and Correlation ID
is sent in DATA to all ASPs whenever a new ASP becomes Active.
+ TEST CONFIGURATION: C with AS in Broadcast Mode.
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1 and ASP2. ASP1 and ASP2 in AS are active and traffic handling
mode for AS is Broadcast. Arrange the DATA in ASP1 and ASP2 such
that it sends ASPIA and ASPAC message with Traffic Mode as
Broadcast mode and for routing context P. Arrange DATA at SGP to
send Transfer Request with Data for RC P.
EXPECTED MESSAGE SEQUENCE :
ASP1 ASP2 SGP SM + NIF
ASP1 & ASP2 are Active
<----------- MTP-Transfer Req
DPC X
<-------------------------------------------- DATA
<-------------------------------- DATA
ASPIA ---------------->
(ASP2, Mode=Broadcast)
Status Ind ------->
<--------------- ASP-Inactive-Ack
<----------- MTP-Transfer Req
DPC X
Anshoo Sharma, HSS [Page 99]
Internet Draft M3UA Conformance Test Plan Jan 2003
<-------------------------------------------- DATA
ASPAC ---------------->
(ASP2, Mode=Broadcast)
Status Ind ------->
<--------------- ASP-Active-Ack
<----------- MTP-Transfer Req
DPC X
<-------------------------------------------- DATA
<-------------------------------- DATA
(Correlation ID Present in DATA)
TEST DESCRIPTION:
1. Send Transfer Request to SGP for DPC X and RC P.
2. Check A: DATA should be sent form SGP to ASP1 and ASP2 with
RC P.
3. Send ASPIA from ASP2 to SGP for RC P.
4. Check B: ASPIA-Ack should be sent from SGP to ASP2 for RC P
and state of ASP2 at SGP should change to ASP-Inactive.
5. Send Transfer Request to SGP for DPC X and RC P.
6. Check C: DATA should be sent from SGP to ASP1 with RC P and
no DATA should be sent to ASP2.
7. Send ASPAC from ASP2 to SGP for RC P.
8. Check D: ASPAC-Ack should be sent from SGP to ASP2 for RC P
and state of ASP2 at SGP should change to ASP-Active.
9. Send Transfer Request to SGP for DPC X and RC P.
10.Check E: DATA should be sent form SGP to ASP1 and ASP2 with
RC P.
Anshoo Sharma, HSS [Page 100]
Internet Draft M3UA Conformance Test Plan Jan 2003
4.6 SCTP Connection Management
Test Cases for SCTP Connection Management Procedures.
"SCTP Connection Establishment"
+ TEST NUMBER : 6.1
+ TITLE : SCTP Connection Management
+ SUBTITLE : SCTP Connection Establishment
+ PURPOSE: To check that on receiving Communication Up primitive from
SCTP, SGP M3UA will send M-SCTP-Establish indication to the SM.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is not established between SGP
and ASP1. Also arrange the data in AS such that SCTP association is
established between ASP1 and SGP.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM
SCTP Establish request to SCTP
SCTP association will be established by SCTP
SGP will receive Communication-Up primitive from SCTP
M-SCTP-Establish Ind ------->
ASPUP ------------------>
Status Ind --------->
<----------------- ASP-Up-Ack
<----------------- NTFY(AS-Inactive)
TEST DESCRIPTION:
1. Make an SCTP association between ASP1 and SGP. SGP will receive
Communication Up primitive from SCTP.
2. Check A:SM receives M-SCTP-Establish indication.
3. Send ASPUP message from AS to SG
4. Check B: ASP-Up-Ack and NTFY message with status ASP-Inactive should
be received.
Anshoo Sharma, HSS [Page 101]
Internet Draft M3UA Conformance Test Plan Jan 2003
"SCTP Connection Termination"
+ TEST NUMBER : 6.2
+ TITLE : SCTP Connection Management
+ SUBTITLE : SCTP Connection Termination
+ PURPOSE: To check that on receiving SCTP-Communication Down
indication primitive from SCTP, AS will send the M-SCTP Status
primitive to the upper layer.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP1. Arrange for terminating the SCTP association between ASP1 and
SGP.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Inactive
ASPDN ----------------->
Status Ind --------->
<----------------- ASP-Down-Ack
SCTP association is terminated
SGP will receive Communication-Down primitive from SCTP
M-SCTP Status -------->
<-------- MTP-Transfer
Send Failure --------->
TEST DESCRIPTION:
1. Terminate the association between SGP and ASP.
2. Check A: SCTP association will be down and on receiving
Communication Down primitive from SCTP, M-SCTP Status indication
will be received at SM.
3. Check B: State of AS will be down at the SGP. Send MTP-Transfer
primitive from the NIF to send some Protocol DATA. SGP will report
send failure.
Anshoo Sharma, HSS [Page 102]
Internet Draft M3UA Conformance Test Plan Jan 2003
"SCTP Connection Restart"
+ TEST NUMBER : 6.3
+ TITLE : SCTP Connection Management
+ SUBTITLE : SCTP Connection Restart
+ PURPOSE: To check that on receiving SCTP-Communication Restart
Indication primitive from SCTP, ASP state at SGP will change to
ASP Down.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is in active state. Also arrange such that the SCTP
association is restarted between SGP and ASP.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + SU
ASP is active
ASP will receive Communication-Restart Primitive from SCTP
M-SCTP Status -------->
Status Ind --------> ASP Down
|
| [ T(r) Expires]
--- Status Ind --------> AS Down
ASPUP ------------------>
Status Ind -------->
<----------------- ASP-Up-Ack
<----------------- NTFY(AS-Inactive)
TEST DESCRIPTION:
1. Invoke a Connection Restart on the association between SGP and ASP.
2. Check A: SCTP association will be restarted and on receiving
Communication Restart primitive from SCTP, M-SCTP Status indication
and an ASP Status Ind will be received at the SM.
3. Check B: State of ASP will change to Down and the SCTP association
Anshoo Sharma, HSS [Page 103]
Internet Draft M3UA Conformance Test Plan Jan 2003
between SGP and ASP still exists.
4. Send an ASP-Up Message from the ASP side to the SGP.
5. Check C: Active-Ack and NTFY would be received at the ASP and the
state of the ASP at the SGP would change to ASP Inactive.
Anshoo Sharma, HSS [Page 104]
Internet Draft M3UA Conformance Test Plan Jan 2003
"SCTP Connection Establishment"
+ TEST NUMBER : 6.4
+ TITLE : SCTP Connection Management
+ SUBTITLE : SCTP Connection Establishment
+ PURPOSE: To check that on receiving M-SCTP-Establish primitive from
SM, SGP initiates and establishes an SCTP association with the ASP.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is not established between SGP
and ASP. Also arrange the data in SGP such that SM sends
M-SCTP-Establish primitive to M3UA with the ASP id to which the
connection is to be established.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SU + SM
<--------- M-SCTP-Establish Request
<------------------->
SCTP association will be established by SCTP
SGP will receive Communication-Up primitive from SCTP
M-SCTP-Establish Ind------->
TEST DESCRIPTION:
1. Send M-SCTP-Establish Request Primitive from the SM at SGP side to
establish an SCTP association with the ASP.
2. Check A: SCTP association will be established and M-SCTP-Establish
indication will be received at the SM.
Anshoo Sharma, HSS [Page 105]
Internet Draft M3UA Conformance Test Plan Jan 2003
4.7 Dynamic Routing Key (RK) Management
Test Cases to test Dynamic RK Management Procedures.
"Routing Key Registration"
+ TEST NUMBER : 7.1
+ TITLE : Routing Key Registration
+ SUBTITLE : Registration of a new RK at SGP.
+ PURPOSE: To check that on receiving a Routing Key Registration
Request for a new valid RK from an ASP, the SGP adds a RK and
confirms the registration to the ASP.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. The ASP is in Inactive State or Active for atleast one RC at
the SGP. The Routing Key RK1 is not configured at the SGP side.
Arrange Data in ASP such that a Routing Key Registration request is
sent from ASP to SGP on stream 0.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Inactive or Active for some RC.
<-------- MTP-Transfer(For RK1)
Send Failure --------->
REG REQ(RK1) ----------------->
RK REG Ind -------->
<----------------- REG RSP (SUCCESS, RC1)
ASPAC(RC1) ---------------->
Status Ind ------->
To ASP <---------------- ASP-Active-Ack
<---------------- NTFY(AS - Active)
Anshoo Sharma, HSS [Page 106]
Internet Draft M3UA Conformance Test Plan Jan 2003
<-------- MTP-Transfer(For RK1)
To ASP <--------------- DATA
TEST DESCRIPTION:
1. Select a valid RK1 (Eg. DPC = Z, SIO = 5) that is not already
configured at the SGP. Send Data for RK1 Reg Request from SGP
side.
2. Check A: A Send Failure would be reported at the SGP Side.
3. Send a valid Reg Req message from ASP to SGP Stack.
4. Check B: A REG_IND would be received at the NIF(SM) and a
REG_RSP message would be received at the ASP side with RC
value and a Success Status for REG_REQ. Check that the AS
to which ASP has been added has the same configurarion as
requested in the Dynamic Registration.
5. Send a ASPAC from ASP to SGP for RC1.
6. Check C: A Status Ind for ASP Active for RC1 is received at
the NIF(SM). Active-Ack with RC1 is received at ASP and Notify
with State AS Active for RC1 is received at the SGP.
7. Send Data for RK1 from SGP.
8. Check D: Data Message is received at the ASP side.
Note: In some implementations, when Data is sent for an
unconfigured RK then instead of giving a Send Failure the Stack
may route the Data to a Default AS .
Anshoo Sharma, HSS [Page 107]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Routing Key DeRegistration"
+ TEST NUMBER : 7.2
+ TITLE : Routing Key DeRegistration
+ SUBTITLE : DeRegistration from an existing RK at SGP.
+ PURPOSE: To check that on receiving a Routing Key Deregistration
Request for a existing RK from an ASP, the SGP removes the
requesting ASP from the List of ASPs serving that RK.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP
and ASP. The Routing Key RK1 is configured at the SGP side.
The ASP is in Active State for RK1 at the SGP. Arrange Data in
ASP such that a Routing Key DeRegistration request for RK1 is
sent from ASP to SGP on stream 0.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Active in AS with RK1.
ASPIA(RC1) ---------------->
Status Ind ------->
To ASP <---------------- ASP-Inactive-Ack
<---------------- NTFY(AS - Inactive)
DEREG REQ(RC1) ----------------->
RK DEREG Ind -------->
<----------------- DEREG RSP (SUCCESS, RC1)
TEST DESCRIPTION:
1. Send an ASPIA message to the SGP from ASP with the RC as the
RC with which RK1 is configured at the SGP.
2. Check A: A Status Ind is received at the NIF. ASPIA-Ack is
received at the ASP and NTFY with RC1 and Status AS-Inactive
is received at the ASP.
Anshoo Sharma, HSS [Page 108]
Internet Draft M3UA Conformance Test Plan Jan 2003
3. Send DeReg Req message with RC as RC1 from ASP to SGP.
4. Check B: A DEREG_IND would be received at the NIF(SM) and a
DEREG_RSP message would be received at the ASP side with RC
value as RC1 and a Success Status for DEREG_REQ.
Anshoo Sharma, HSS [Page 109]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Routing Key Registration"
+ TEST NUMBER : 7.3
+ TITLE : Routing Key Registration
+ SUBTITLE : Registration in an existing AS at SGP.
+ PURPOSE: To check that on receiving a Routing Key Registration
Request for a existing RK from an ASP, the SGP adds the
requesting ASP to the List of ASPs serving that RK.
+ TEST CONFIGURATION: C
+ PRE-TEST CONDITIONS: SCTP association is established between SGP
and ASP1 and SGP and ASP2. The Routing Key RK1 is configured at
the SGP side. The ASP1 is in Inactive State at the SGP and ASP2
is actively handling Traffic for RK1 with RC value as RC1. The
AS for RK1 is in Traffic Mode Override. Arrange Data in ASP such
that a valid Routing Key Registration with Traffic Mode
consistent with mode at SG request for RK1 is sent from ASP to
SGP on stream 0.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP1 is Inactive
<-------- MTP-Transfer(For RK1)
To ASP2 <--------------- DATA
From ASP1
REG REQ(RK1) ----------------->
RK REG Ind -------->
<----------------- REG RSP (SUCCESS, RC1)
From ASP1
ASPAC(RC1) ---------------->
Status Ind ------->
To ASP1 <---------------- ASP-Active-Ack
<---------------- NTFY(AS - Active)
Anshoo Sharma, HSS [Page 110]
Internet Draft M3UA Conformance Test Plan Jan 2003
<-------- MTP-Transfer(For RK1)
To ASP1 <--------------- DATA
TEST DESCRIPTION:
1. Send a Data Message from SGP for RK1.
2. Check A: Data would be received at ASP2.
3. Send a valid Reg Req message for RK1 from ASP1 to SGP Stack.
4. Check B: A REG_IND would be received at the NIF(SM) and a
REG_RSP message would be received at the ASP1 with RC
value as RC1 and a Success Status for REG_REQ.
5. Send a ASPAC with Traffic Mode Override from ASP to SGP for RC1.
6. Check C: A Status Ind for ASP Active for RC1 is received at
the NIF(SM). Active-Ack with RC1 is received at ASP and Notify
with State AS Active for RC1 is received at the SGP.
7. Send a Data Message from SGP for RK1.
8. Check D: Data would be received at ASP2.
Anshoo Sharma, HSS [Page 111]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Routing Key Registration"
+ TEST NUMBER : 7.4
+ TITLE : Routing Key Registration Failure
+ SUBTITLE : RK Registration Fails when ASP is Active for the RK.
+ PURPOSE: To check that on receiving a Routing Key Registration
Request for an existing RK from an ASP which is already active
for the RK, the Registration Fails and a Negative Response
Message is sent to the ASP.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP
and ASP. The Routing Key RK1 is configured at the SGP side.
The ASP is in Active State for RK1 at the SGP. Arrange Data in
ASP such that a Routing Key Registration request for RK1 is sent
from ASP to SGP on stream 0.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Active for RK1
REG REQ(RK1) ----------------->
<----------------- REG RSP (FAILURE, RK not Provisioned)
<-------- MTP-Transfer(For RK1)
To ASP <--------------- DATA
TEST DESCRIPTION:
1. Send a valid Reg Req message for RK1 from ASP to SGP Stack.
2. Check B: REG_RSP message would be received at the ASP side with
Failure Response.
3. Send a Data Message from SGP for RK1.
4. Check C: Data would be received at ASP.
Anshoo Sharma, HSS [Page 112]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Routing Key Deregistration"
+ TEST NUMBER : 7.5
+ TITLE : Routing Key Deregistration Failure
+ SUBTITLE : RK Deregistration Fails when ASP is Active for the RK.
+ PURPOSE: To check that on receiving a Routing Key Deregistration
Request for an existing RK from an ASP which is active
for the RK, the Deregistration Fails and a Failure Response
Message is sent to the ASP.
+ TEST CONFIGURATION: A
+ PRE-TEST CONDITIONS: SCTP association is established between SGP
and ASP. The Routing Key RK1 is configured at the SGP side.
The ASP is in Active State for RK1 at the SGP. Arrange Data in
ASP such that a Routing Key DeRegistration request for RK1 is sent
from ASP to SGP on stream 0.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP is Active for RK1
DEREG REQ(RC1) ----------------->
<----------------- DEREG RSP (FAILURE)
Err Code: ASP Currently Active for RC
TEST DESCRIPTION:
1. Send a valid DeReg Req message for RK1 from ASP to SGP Stack.
2. Check A: A DEREG_RSP would be received at the ASP side with
Registration Status as Failed and Error Code as "ASP Currently
Active for Routing Context".
Anshoo Sharma, HSS [Page 113]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Routing Key Registration"
+ TEST NUMBER : 7.6
+ TITLE : Routing Key Registration
+ SUBTITLE : Unique RC Value for a given RK.
+ PURPOSE: To check that on receiving a Routing Key Registration
Request from two different ASPs at the SGP Stack, the SGP
allocates the same RC ID to both of these.
+ TEST CONFIGURATION: C
+ PRE-TEST CONDITIONS: SCTP association is established between SGP
and ASP1 and SGP and ASP2. Both ASP1 and ASP2 are in Inactive
State at the SGP. Arrange Data in ASP1 and ASP2 such that a
valid Routing Key Registration request for RK1 is sent from ASP
to SGP on stream 0.
EXPECTED MESSAGE SEQUENCE :
ASP SGP SM + NIF
ASP1 and ASP2 are Inactive
From ASP1
REG REQ(RK1) ----------------->
RK REG Ind -------->
<----------------- REG RSP (SUCCESS, RC1)
From ASP2
REG REQ(RK1) ----------------->
RK REG Ind -------->
<----------------- REG RSP (SUCCESS, RC1)
TEST DESCRIPTION:
1. Send a valid Reg Req message for RK1 from ASP1 to SGP Stack.
2. Check B: A REG_IND would be received at the NIF(SM) and a
REG_RSP message would be received at the ASP1 with RC
value as RC1 and a Success Status for REG_REQ.
Anshoo Sharma, HSS [Page 114]
Internet Draft M3UA Conformance Test Plan Jan 2003
3. Send a valid Reg Req message for RK1 from ASP2 to SGP Stack.
4. Check B: A REG_IND would be received at the NIF(SM) and a
REG_RSP message would be received at the ASP2 with RC
value again as RC1 and a Success Status for REG_REQ.
Anshoo Sharma, HSS [Page 115]
Internet Draft M3UA Conformance Test Plan Jan 2003
5 Test Cases for Testing M3UA at ASP
Following Tests are to be carried out when the Implementation Under
Test is ASP.
5.1 MANAGEMENT
Test Cases to test Management Procedures. "Invalid Version Error"
+ TEST NUMBER : 1.1
+ TITLE : Invalid Message Handling
+ SUBTITLE : Invalid Version Error
+ PURPOSE: To check that if any message with Invalid version is
received at the ASP then ASP responds with ERROR message containing
cause "Invalid Version" and diagnostic information filled with the
version the SGP supports.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is Active. Also arrange the data in SGP such that DUNA
message is sent on stream 0 with the version other than Version 1.0
protocol to the ASP. N/w appearance parameters in the DUNA message
should be A and affected DPC can be having any DPC.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
ASP is active
DUNA --------------->
Version = 2
<-------------- ERROR
Cause = Invalid Version
TEST DESCRIPTION:
1. Send DUNA message from SGP to ASP containing version 2 in the common
header.
2. Check A: ERROR message containing cause Invalid Version will be
received at SGP.
3. Check B: Diagnostic Parameter in ERROR is filled with version 1.
However Diagnostic Information is optional so this may not be the
case in all implementations.
4. Repeat the above test cases for other messages from SGP to ASP like
DAVA, SCON, DUPU, DRST, NTFY and DATA.
Anshoo Sharma, HSS [Page 116]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Unrecognized Message Type"
+ TEST NUMBER : 1.2
+ TITLE : Invalid Message Handling
+ SUBTITLE : Unrecognized Message Type
+ PURPOSE: To check that if a message with message type not defined is
received at ASP, ASP responds with ERROR message containing cause
"Invalid Message Type".
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is Active. Arrange the data in SGP such that a message
with Message type not defined is sent to ASP. Let the other
parameters in the message be like any other message.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
ASP is active
Message --------------->
Message Type = 0408
<-------------- ERROR
Cause = Invalid Message Type
DATA --------------->
N/w Appearance A
MTP-Transfer Ind --------->
TEST DESCRIPTION:
1. Send a message with message type 0408 or any other value which is
not defined from SGP to ASP.
2. Check A: ERROR message containing cause Invalid Message Type will be
received at the SGP.
3. Check B: State of ASP is not disturbed.
Anshoo Sharma, HSS [Page 117]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Invalid Network Appearance"
+ TEST NUMBER : 1.3
+ TITLE : Invalid Message Handling
+ SUBTITLE : Invalid Network Appearance
+ PURPOSE: To check that if a message with invalid network appearance
i.e. ASP does not handle traffic for that network appearance then ASP
responds with ERROR message containing cause "Invalid Network
Appearance".
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is Active. Arrange the data in SGP such that DATA message
with invalid value of Network Appearance is sent to ASP.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
ASP is active
DATA --------------->
N/w appearance B
<-------------- ERROR
Cause = Invalid Network Appearance
DATA --------------->
N/w Appearance A
MTP-Transfer Ind --------->
TEST DESCRIPTION:
1. Send DATA message to the ASP with network appearance which ASP
doesn't handle.
2. Check A: ASP will respond with ERROR message containing cause
Invalid Network Appearance.
3. Check B: State of ASP at AS is not disturbed.
4. Repeat the above test case for other messages like DUNA, DAVA, DUPU,
DRST and SCON.
Anshoo Sharma, HSS [Page 118]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Invalid Congestion Level in SCON message"
+ TEST NUMBER : 1.4
+ TITLE : Invalid Message Handling
+ SUBTITLE: Invalid congestion level in SCON message.
+ PURPOSE: To check that if SCON message with Invalid congestion level
parameter is received then it is reported to the upper layer.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is active. Arrange the data in SGP such that SCON message
with congestion level with value 4 or more is sent to the ASP. In
N/w Appearance parameter in SCON message, fill value A and for
affected DPC fill any value.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
ASP is active
SCON --------------->
Congestion Level 4
<-------------- ERROR
Cause = Invalid Parameter Value
DATA --------------->
N/w Appearance A
MTP-Transfer Ind --------->
TEST DESCRIPTION:
1. Send SCON message with congestion Level 4.
2. Check A: ASP will send an ERROR Message with Invalid Parameter Value
to SGP.
3. Send a DATA Message to the ASP.
5. Check B: Transfer Indication will be given to the SU at ASP and
State of ASP is not disturbed.
Anshoo Sharma, HSS [Page 119]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Invalid Cause parameter in DUPU message"
+ TEST NUMBER : 1.5
+ TITLE : Invalid Message Handling
+ SUBTITLE : Invalid Cause parameter in DUPU message
+ PURPOSE: To check that if DUPU message with Invalid cause parameter
is received then error will be reported to SM.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is Active. Arrange the data in SGP such that DUPU message
with invalid value of cause parameter is sent to ASP. In N/w
Appearance parameter fill value A and affected destination parameter
fill any value. In the user parameter fill any valid value.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
ASP is active
DUPU --------------->
Cause 03
<-------------- ERROR
Cause = Invalid Parameter Value
DATA --------------->
N/w Appearance A
MTP-Transfer Ind --------->
TEST DESCRIPTION:
1. Send DUPU message from the SGP with cause value 03 or more to the
ASP.
2. Check A: ASP will send an ERROR to the SGP with Cause as
Invalid Parameter Value.
3. Check B: State of ASP is not disturbed.
4. Repeat the above test case for invalid value of User parameter in
DUPU message(11 or more).
Anshoo Sharma, HSS [Page 120]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Message length less than the length of mandatory Parameters"
+ TEST NUMBER : 1.6
+ TITLE : Invalid Message Handling
+ SUBTITLE : Message length less than length of mandatory parameters
+ PURPOSE: To check that if a message with value of length parameter
less than length of mandatory parameters is received then message is
discarded.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP, and ASP is Down. Arrange the data in SGP such that ASPUP-Ack
message with length parameter filled with value less than the length
of Common Message Header.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
<--------- ASP-Up
<----------- ASPUP
ASP-Up-Ack ------------>
<----------- ERROR
<----------- ASPUP
TEST DESCRIPTION:
1. Send ASP-Up primitive from SM to the M3UA at the ASP. ASPUP message
will be sent to the SGP.
2. Send ASP-Up-Ack message with length field less than the length of
Common Message Header from the SGP.
3. Check A: ASP will send an ERROR message to the SGP and discard the
Message.
4. Check B: ASPUP message will be sent again after ASPSM Timer Expiry.
Note: Resending of ASPUP is implementation Dependent.
Anshoo Sharma, HSS [Page 121]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ERROR Handling"
+ TEST NUMBER : 1.7
+ TITLE : ERROR
+ SUBTITLE : Handling of Received Error
+ PURPOSE: To check that if an error is received then that is reported
to the SM and no action is taken against that.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is in active state at the SGP. Arrange data in SGP such that
ERROR with cause invalid version is sent to the ASP.
EXPECTED MESSAGE SEQUENCE:
SGP ASP SU
ASP is active
ERROR --------------->
Cause = invalid version Error -------->
TEST DESCRIPTION:
1. Send ERROR message with cause invalid version from SG to ASP.
2. Check A: ASP should report the error to its SM.
3. Check B: Further action at the SGP are implementation dependent.
4. Repeat the test case for other cause values in ERROR message.
Anshoo Sharma, HSS [Page 122]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Invalid Routing Context"
+ TEST NUMBER : 1.8
+ TITLE : Invalid Message Handling
+ SUBTITLE : Invalid Routing Context
+ PURPOSE: To check that if a message with Invalid Routing Context
i.e. ASP does not handle traffic for that Routing Context then ASP
responds with ERROR message containing cause "Invalid Routing
Context".
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is Active for RC P and RC M is not configured on the ASP
side. Arrange the data in SGP such that DATA message with invalid
value of Routing Context(M) is sent to ASP.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
ASP is active
DATA --------------->
N/w appearance A, RC = M
<-------------- ERROR
Cause = Invalid Routing Context
DATA --------------->
N/w Appearance A, RC = P
MTP-Transfer Ind --------->
TEST DESCRIPTION:
1. Send DATA message to the ASP with routing context which ASP
doesn't handle.
2. Check A: ASP will respond with ERROR message containing cause
Invalid Routing Context.
3. Check B: State of ASP at ASP is not disturbed.
4. Repeat the above test case for other messages like DUNA, DAVA, DUPU,
DRST and SCON.
Note: Routing Context is an optional field and some implementation
might not be using it.
Anshoo Sharma, HSS [Page 123]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Error - Missing Parameter"
+ TEST NUMBER : 1.9
+ TITLE : ERROR
+ SUBTITLE : Error with cause Missing Parameter.
+ PURPOSE: To check that if any message without mandatory parameter is
received at the ASP then ASP responds with ERROR message containing
cause "Missing Parameter".
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is Active. Also arrange the data in SGP such that Payload
Data Message is sent without Protocol Data parameter.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SU
ASP is Active
From SGP
DATA ---------------->
(Without Payload)
(SGP) <---------------- ERROR
(Missing Parameter)
TEST DESCRIPTION:
1. Send Payload Data message SGP to ASP without Protocol Data
parameter.
2. Check A: ERROR message is received at the SGP containing Error Code
Missing Parameter.
3. Repeat the above test cases for other messages from SGP to ASP like
like REG RSP, DEREG RSP, SCON, DAVA, DUNA, DUPU, DRST and NOTIFY
without mandatory parameter. In all these cases ERROR message will
be received with the same Error Code.
Anshoo Sharma, HSS [Page 124]
Internet Draft M3UA Conformance Test Plan Jan 2003
5.2 TRANSFER
Test Cases to test TRANSFER Procedures.
"Send and Receive of MTP-Transfer Primitive in AS Active State"
+ TEST NUMBER : 2.1
+ TITLE : MTP-Transfer Primitive
+ SUBTITLE: Send and Receive of MTP-Transfer Primitive
+ PURPOSE: To check that on receiving MTP-Transfer primitive from SU,
DATA message is sent to the SGP.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is in ASP-Active state. Also arrange the data in ASP such
that SU send MTP-Transfer primitive to M3UA with N/w Appearance A.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SU
ASP is Active
a)
<----------- MTP-Transfer
<------------- DATA N/w appearance A
b)
DATA -------------->
MTP-Transfer --------->
TEST DESCRIPTION:
1. Send MTP-Transfer Request Primitive from the SU at ASP to send
Protocol Data to the SGP.
2. Check A: DATA message is received at ASP containing the data passed
by the SU and the Network Appearance.
3. Send DATA message from SGP containing Protocol Data and N/w
Appearance A to the ASP.
4. Check B: MTP-Transfer primitive is received at SU with the Protocol
Data and N/w Appearance.
5. Repeat the test step 3 if DATA message is sent without N/w
appearance parameter. Response should be same as in 4.
Note: In some implementation, N/w appearance parameter may not be
there in the DATA message sent from ASP to SGP.
Anshoo Sharma, HSS [Page 125]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Stream Selection "
+ TEST NUMBER : 2.2
+ TITLE : Stream Selection
+ SUBTITLE : Stream Selection
+ PURPOSE: To check that all the messages for the same call are sent
on the same SCTP stream.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP with two or more streams. ASP is active. Also arrange the data in
ASP such that SU sends three or more MTP-Transfer Request
primitive to M3UA containing the same CIC value and N/w Appearance A.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SU
AS is active
<--------- MTP-Transfer
Check Stream id <------------- DATA Data with CIC X
<--------- MTP-Transfer
Check Stream id <------------- DATA Data with CIC X
<--------- MTP-Transfer
Check Stream id <------------- DATA Data with CIC X
TEST DESCRIPTION:
1. Send three or more MTP-Transfer Request Primitive from the SU at SGP
side to send Protocol Data to the ASP. In the Protocol data CIC
values should be same in all MTP-Transfer Request primitive.
It is assumed that load sharing across the streams is CIC based.
2. Check A: DATA messages are sent to the SGP containing the same
Stream Sequence number.
3. Repeat the above test with same SLS value in Protocol Data in all
MTP-Transfer Request primitives assuming load sharing across the
streams is SLS based.
4. Repeat the above test case with different CIC values and different
SLS values. DATA messages should be sent on different streams.
Note: How the messages will be distributed on different streams based
on CIC and SLS is implementation dependent.
Anshoo Sharma, HSS [Page 126]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Routing among SGPs within an SG"
+ TEST NUMBER : 2.3
+ TITLE : Data Routing from the ASP among SGPs within an SG.
+ SUBTITLE : Data Routing from ASP when SG Mode is Loadshare.
+ PURPOSE: To check that the Data Message from the ASP is routed
according to the mode of the SG.
+ TEST CONFIGURATION: J
+ PRE-TEST CONDITIONS: SCTP association is established between SGP1 and
ASP and SGP2 and ASP. ASP is Active for RC P in SGP1 and is down in
SGP2. Also arrange the data in ASP such that SU sends a MTP-Transfer
Indication primitive to M3UA containing the RC value P and
N/w Appearance A and CIC values S and T. Also arrange Data at SGP2 to
send ASPUP-Ack and ASPAC-Ack for RC = P.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SU
ASP is Active in SGP1 and
ASP is Down in SGP2.
<----------- MTP-Transfer Req
DPC Y & CIC S
To SGP1 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC T
To SGP1 <--------------- DATA
To SGP2 <---------------- ASPUP
ASPUP-Ack --------------->
Status Ind ------->
To SGP2 <---------------- ASPAC (RC = P)
ASPAC-Ack --------------->
Status Ind ------->
Anshoo Sharma, HSS [Page 127]
Internet Draft M3UA Conformance Test Plan Jan 2003
<----------- MTP-Transfer Req
DPC Y & CIC S
To SGP1 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC T
To SGP2 <--------------- DATA
TEST DESCRIPTION:
1. Send two MTP-Transfer Request Primitive from the SU at ASP side
with CIC values S and T respectively. It is assumed that load
sharing across the streams is CIC based.
2. Check A: Both DATA messages reach SGP1.
3. Bring ASP in Active State for RC P in SGP2 by the Message
Sequence shown above.
4. Repeat the Step1 with appropriate CIC values (S,T) for loadsharing.
5. Check B: DATA should be loadshared among SGP1 and SGP2. i.e. One
DATA message should reach SGP1 and the other should reach SGP2.
Note: How the messages will be loadshared based on CIC and SLS is
implementation dependent.
Anshoo Sharma, HSS [Page 128]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Routing among SGPs within an SG"
+ TEST NUMBER : 2.4
+ TITLE : Data Routing from the ASP among SGPs within a SG.
+ SUBTITLE : Data Routing from ASP when SG Mode is Broadcast.
+ PURPOSE: To check that the Data Message from the ASP is routed
according to the mode of the SG.
+ TEST CONFIGURATION: J
+ PRE-TEST CONDITIONS: SCTP association is established between SGP1 and
ASP and SGP2 and ASP. ASP is Active for RC P in SGP1 and is down in
SGP2. Also arrange the data in ASP such that SU sends a MTP-Transfer
Indication primitive to M3UA containing the RC value P and
N/w Appearance A and CIC values S and T. Also arrange Data at SGP2 to
send ASPUP-Ack and ASPAC-Ack for RC = P.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SU
ASP is Active in SGP1 and
ASP is Down in SGP2.
<----------- MTP-Transfer Req
DPC Y
To SGP1 <--------------- DATA
To SGP2 <---------------- ASPUP
ASPUP-Ack --------------->
Status Ind ------->
To SGP2 <---------------- ASPAC (RC = P)
ASPAC-Ack --------------->
Status Ind ------->
<----------- MTP-Transfer Req
DPC Y
To SGP1 <--------------- DATA
Anshoo Sharma, HSS [Page 129]
Internet Draft M3UA Conformance Test Plan Jan 2003
To SGP2 <--------------- DATA
TEST DESCRIPTION:
1. Send a MTP-Transfer Request Primitive from the SU at ASP side.
2. Check A: A DATA messages reach SGP1.
3. Bring ASP in Active State for RC P in SGP2 by the Message
Sequence shown above.
4. Repeat Step1.
5. Check B: Same DATA should reach SGP1 and SGP2. i.e. One
MTP Transfer Primitive at ASP should cause dispatch of two
DATA messages for SGP1 and SGP2.
Anshoo Sharma, HSS [Page 130]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Routing among SGPs within different SGs"
+ TEST NUMBER : 2.5
+ TITLE : Data Routing from the ASP among SGPs within different SGs.
+ SUBTITLE : Data Routing from ASP for SGs in Loadshare Mode.
+ PURPOSE: To check that the Data Message from the ASP is routed
according to the number of SGPs in which the PC is available and
mode of the SGs.
+ TEST CONFIGURATION: K, with both SG1 and SG2 in Loadshare Mode.
+ PRE-TEST CONDITIONS: SCTP association is established between all
SGPs and the ASP. ASP is Active for RC P in SGP1 and is down in
SGP2, SGP3 and SGP4. Also arrange the data in ASP such that SU sends
a MTP-Transfer Request primitive to M3UA containing the RC value P
and N/w Appearance A and CIC values S, T, U and V. Also arrange Data
at SGPs to send ASPUP-Ack and ASPAC-Ack for RC = P.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SU
ASP is Active in SGP1.
ASP is Down in SGP2, SGP3, SGP4.
<----------- MTP-Transfer Req
DPC Y & CIC S
To SGP1 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC T
To SGP1 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC U
To SGP1 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC V
To SGP1 <--------------- DATA
To SGP3 <---------------- ASPUP
ASPUP-Ack --------------->
Anshoo Sharma, HSS [Page 131]
Internet Draft M3UA Conformance Test Plan Jan 2003
Status Ind ------->
To SGP3 <---------------- ASPAC (RC = P)
ASPAC-Ack --------------->
Status Ind ------->
<----------- MTP-Transfer Req
DPC Y & CIC S
To SGP1 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC T
To SGP1 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC U
To SGP3 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC V
To SGP3 <--------------- DATA
To SGP2 <---------------- ASPUP
ASPUP-Ack --------------->
Status Ind ------->
To SGP2 <---------------- ASPAC (RC = P)
ASPAC-Ack --------------->
Status Ind ------->
<----------- MTP-Transfer Req
DPC Y & CIC S
To SGP1 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC T
To SGP2 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC U
To SGP3 <--------------- DATA
To SGP4 <---------------- ASPUP
Anshoo Sharma, HSS [Page 132]
Internet Draft M3UA Conformance Test Plan Jan 2003
ASPUP-Ack --------------->
Status Ind ------->
To SGP4 <---------------- ASPAC (RC = P)
ASPAC-Ack --------------->
Status Ind ------->
<----------- MTP-Transfer Req
DPC Y & CIC S
To SGP1 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC T
To SGP2 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC U
To SGP3 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC V
To SGP4 <--------------- DATA
TEST DESCRIPTION:
1. Send Four MTP-Transfer Request Primitive from the SU at ASP side
with CIC values S, T, U and V respectively. It is assumed that
load sharing across the streams is CIC based.
2. Check A: All DATA messages reach SGP1.
3. Bring ASP in Active State for RC P in SGP3 by the Message
Sequence shown above.
4. Repeat the Step1 with appropriate CIC values (S,T,U,V) for
loadsharing among two Destinations.
5. Check C: DATA should be loadshared among SG1 and SG2 and hence
among SGP1 and SGP3 i.e. Two DATA message should reach SGP1
and the other two should reach SGP3.
6. Bring ASP in Active State for RC P in SGP2 by the Message
Sequence shown above.
7. Repeat the Step1 with appropriate CIC values (S,T,U,V) for
loadsharing among three Destinations.
8. Check D: DATA should be loadshared among SGP1, SGP2 and SGP3.
9. Bring ASP in Active State for RC P in SGP4 by the Message
Anshoo Sharma, HSS [Page 133]
Internet Draft M3UA Conformance Test Plan Jan 2003
Sequence shown above.
10.Repeat the Step1 with appropriate CIC values (S,T,U,V) for
loadsharing among four Destinations.
11.Check E: DATA should be loadshared among SGP1, SGP2, SGP3
and SGP4.
Note: How the messages will be loadshared based on CIC and SLS is
implementation dependent.
Anshoo Sharma, HSS [Page 134]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Routing among SGPs within different SGs"
+ TEST NUMBER : 2.6
+ TITLE : Data Routing from the ASP among SGPs within different SGs.
+ SUBTITLE : Data Routing from ASP for SGs in Loadshare and Broadcast
Mode.
+ PURPOSE: To check that the Data Message from the ASP is routed
according to the number of SGPs in which the PC is available and
mode of the SGs.
+ TEST CONFIGURATION: K, with SG2 in Loadshare and SG1 in Broadcast.
+ PRE-TEST CONDITIONS: SCTP association is established between all SGPs
and the ASP. ASP is Active for RC P in SGP1 and is down in SGP2, SGP3
and SGP4. Also arrange the data in ASP such that SU sends a
MTP-Transfer Request primitive to M3UA containing the RC value P
and N/w Appearance A and CIC values S, T, U and V. Also arrange Data
at SGPs to send ASPUP-Ack and ASPAC-Ack for RC = P.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SU
ASP is Active in SGP1.
ASP is Down in SGP2, SGP3, SGP4.
<----------- MTP-Transfer Req
DPC Y & CIC S
To SGP1 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC U
To SGP1 <--------------- DATA
To SGP3 <---------------- ASPUP
ASPUP-Ack --------------->
Status Ind ------->
To SGP3 <---------------- ASPAC (RC = P)
ASPAC-Ack --------------->
Anshoo Sharma, HSS [Page 135]
Internet Draft M3UA Conformance Test Plan Jan 2003
Status Ind ------->
<----------- MTP-Transfer Req
DPC Y & CIC S
To SGP1 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC U
To SGP3 <--------------- DATA
To SGP2 <---------------- ASPUP
ASPUP-Ack --------------->
Status Ind ------->
To SGP2 <---------------- ASPAC (RC = P)
ASPAC-Ack --------------->
Status Ind ------->
<----------- MTP-Transfer Req
DPC Y & CIC S
To SGP1 <--------------- DATA
To SGP2 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC U
To SGP3 <--------------- DATA
To SGP4 <---------------- ASPUP
ASPUP-Ack --------------->
Status Ind ------->
To SGP4 <---------------- ASPAC (RC = P)
ASPAC-Ack --------------->
Status Ind ------->
<----------- MTP-Transfer Req
DPC Y & CIC S
Anshoo Sharma, HSS [Page 136]
Internet Draft M3UA Conformance Test Plan Jan 2003
To SGP1 <--------------- DATA
To SGP2 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC T
To SGP3 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC U
To SGP4 <--------------- DATA
TEST DESCRIPTION:
1. Send Two MTP-Transfer Request Primitive from the SU at ASP side
with CIC values S, U respectively. It is assumed that
load sharing across the streams is CIC based.
2. Check A: All DATA messages reach SGP1.
3. Bring ASP in Active State for RC P in SGP3 by the Message
Sequence shown above.
4. Repeat the Step1 with appropriate CIC values (S,U) for
loadsharing among two Destinations.
5. Check C: DATA should be loadshared among SG1 and SG2 and hence
among SGP1 and SGP3 i.e. One DATA message reaches SGP1 and the
other should reach SGP3.
6. Bring ASP in Active State for RC P in SGP2 by the Message
Sequence shown above.
7. Repeat the Step1 with appropriate CIC values (S,U) for
loadsharing among two Destinations.
8. Check D: DATA should be loadshared among SGP1 and SGP3, and
Data reaching SGP1 also reaches SGP2.
9. Bring ASP in Active State for RC P in SGP4 by the Message
Sequence shown above.
10.Repeat the Step1 with appropriate CIC values (S,T,U) for
loadsharing among three Destinations.
11.Check E: DATA should be loadshared among SGP1, SGP3 and SGP4,
and Data reaching SGP1 also reaches SGP2.
Note: How the messages will be loadshared based on CIC and SLS is
implementation dependent.
Anshoo Sharma, HSS [Page 137]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Routing Failure"
+ TEST NUMBER : 2.7
+ TITLE : Routing Failure when AS State is not Active
+ SUBTITLE : MTP Transfer Request Fails when AS is in Inactive State.
+ PURPOSE: To check that on receiving MTP-Transfer primitive from SU,
DATA message is rejected at ASP if the related AS is in inactive
state.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is in ASP-inactive state for the related AS. Also arrange
the data in ASP such that SU send MTP-Transfer primitive to M3UA with
N/w Appearance A.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
ASP is Inactive
<----------- MTP-Transfer Req
DPC Z
Send Failure ------->
To SGP <---------------- ASPAC (RC = P)
ASPAC-Ack --------------->
Status Ind ------->
<----------- MTP-Transfer Req
DPC Z
To SGP <--------------- DATA
TEST DESCRIPTION:
1. Send MTP-Transfer Request Primitive from the SU at ASP to send
Protocol Data to the SGP.
2. Check A: DATA message is rejected at ASP.
3. Send ASPAC message with Routing Context P and check SGP responds
with ASP-Active-Ack and NTFY with status AS-Active.
4. Send MTP-Transfer Request Primitive from the SU at ASP to send
Protocol Data to the SGP.
5. Check B: DATA message is received at SGP.
Anshoo Sharma, HSS [Page 138]
Internet Draft M3UA Conformance Test Plan Jan 2003
5.3 SSNM
Test Cases to Test SSNM Procedures.
"Reception of SSNM messages"
+ TEST NUMBER : 3.1
+ TITLE : SSNM Message handling
+ SUBTITLE: Reception of SSNM messages
+ PURPOSE: To check that if SSNM message is received at the ASP then it
is reported to the ULP.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is Active. Also arrange the data in SGP such that DUNA,
DAVA, DUPU, DRST and SCON messages are sent from the SGP to the ASP
with valid parameters and they are sent on stream number 0.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
AS is active
a)
DUNA --------------->
MTP-Pause Ind -------->
b)
DAVA --------------->
MTP-Resume Ind -------->
c)
SCON --------------->
MTP-Status Ind -------->
d)
DUPU --------------->
MTP-Status Ind -------->
e)
DRST --------------->
Anshoo Sharma, HSS [Page 139]
Internet Draft M3UA Conformance Test Plan Jan 2003
MTP-Status Ind -------->
TEST DESCRIPTION:
1. Send DUNA message from SGP to ASP containing the Network
Appearance A, Routing Context Value P and Affected DPC any value.
2. Check A: MTP-Pause indication primitive will be received at the SU.
3. Repeat the above test case for other messages like DAVA, SCON, DRST
and DUPU messages.
4. Repeat the above test case for one affected DPC and for more than
one affected DPC parameters.
5. Repeat the above test cases if all these messages are sent on stream
number other than zero. They should be accepted.
Note: Depending upon the number of affected destinations there may be
more than one MTP-Pause, MTP-Resume and Status Indication.
Anshoo Sharma, HSS [Page 140]
Internet Draft M3UA Conformance Test Plan Jan 2003
+ TEST NUMBER : 3.2
+ TITLE : SSNM Message handling
+ SUBTITLE: Reception of SSNM messages
+ PURPOSE: To check that Pause, Resume and Status Indications are
is given to the SU only when there is an overall availability
in the Reachability of the Point Code.
+ TEST CONFIGURATION: H
+ PRE-TEST CONDITIONS: SCTP association is established between SGP
belonging to SG1 and ASP and ASP is Active. Also arrange the data in
SGP1 and SGP2 such that DUNA, DAVA, DUPU, DRST and SCON messages are
sent from the SGP to the ASP with valid parameters and they are sent
on stream number 0.
EXPECTED MESSAGE SEQUENCE :
SGP1(SG1) SGP2(SG2) ASP SU
ASP is active and PC Y is
reachable from SG1 and SG2
a)
DUNA -------------------------->
(for Point Code Y and
Routing Context P at SGP1)
b)
DUNA -------------------------->
----------------->
(for Point Code Y and
Routing Context P at
SGP1 and SGP2)
MTP-Pause Ind -------->
ASP is active and PC Y is
unreachable from SG1 and SG2
c)
DAVA -------------------------->
MTP-Resume Ind -------->
Anshoo Sharma, HSS [Page 141]
Internet Draft M3UA Conformance Test Plan Jan 2003
----------------->
(for Point Code Y and
Routing Context P
at SGP1 and SGP2)
TEST DESCRIPTION:
1. Send DUNA message from SGP1 to ASP for Point Code Y and
Routing Context P, when PC Y is reachable through both
SG1 and SG2.
2. Check A: MTP Pause Indication primitive will not be received
at the SU.
3. Send DUNA from SGP1 and SGP2 to ASP for routing Context P.
4. Check B: MTP Pause indication will be received at SU.
5. Send DAVA message from SGP1 and then SGP2 to ASP for Point Code Y
and Routing Context P when Point Code Y is unreachable from both
SG1 and SG2.
6. Check C: MTP Resume indication will be received at SU after DAVA
from SGP1 is received at ASP, and MTP Resume Indication is not
received after DAVA is received from SGP2.
7. Repeat the above test case for other messages like SCON, DRST and
DUPU messages.
8. Repeat the above test cases if all these messages are sent on stream
number other than zero. They should be accepted.
Note: Depending upon the number of affected destinations there may be
more than one MTP-Pause, MTP-resume and Status Indication.
Anshoo Sharma, HSS [Page 142]
Internet Draft M3UA Conformance Test Plan Jan 2003
"DAUD message is not sent if SCON message is received with congestion
level 0 or undefined"
+ TEST NUMBER : 3.3
+ TITLE : SSNM Message Handling
+ SUBTITLE : DAUD message is not sent if SCON message is received with
congestion level 0 or undefined
+ PURPOSE: To check that if SCON message is received with congestion
level 0 or undefined then DAUD message is not sent on expiry of the
timer.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is active. Also arrange the data in SGP such that SCON
message with congestion level 0 is sent to the ASP. Network
Appearance parameter should be having value A and affected DPC can be
having any value.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SU
ASP is active
SCON(Level 1) --------------->
| MTP-Status Ind -------->
|
|Timer expires
<--------------- DAUD
|
|
|Timer expires
<--------------- DAUD
SCON(Level 0) --------------->
|
|
|Timer expires
<--------------- DAUD is not sent
Anshoo Sharma, HSS [Page 143]
Internet Draft M3UA Conformance Test Plan Jan 2003
TEST DESCRIPTION:
1. Send SCON message from the SGP to the ASP. Don't send any other SSNM
message from the SGP. Timer will be started at the ASP on receiving
SCON message.
2. Check A: DAUD message should be received at the SGP after expiry of
the timer.
3. Repeat the above test case if SCON message is sent with SCON Level0.
4. Check B: No DAUD message should be received at the SG after expiry
of the timer.
Note: Value of the timer is implementation specific.
Anshoo Sharma, HSS [Page 144]
Internet Draft M3UA Conformance Test Plan Jan 2003
"On Indication of SCTP Congestion the ASP sends a SCON to SGP"
+ TEST NUMBER : 3.4
+ TITLE : SSNM Message
+ SUBTITLE : SCON Message from ASP
+ PURPOSE: To check that if the ASP detects SCTP Congestion and invokes
a Status Ind with Cause Congestion, an SCON message is sent with the
specified congestion Level.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is active for Routing Context P.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SU
ASP is active
<--------- MTP-Status-Ind (Cong.)
<------------- SCON
TEST DESCRIPTION:
1. SU Invokes MTP-Status-Ind API with cause as congestion and a valid
congestion level value.
2. Check A: SCON message should be received at the SGP with a valid
SCON value.
Anshoo Sharma, HSS [Page 145]
Internet Draft M3UA Conformance Test Plan Jan 2003
"PC Availability Status from SSNM"
+ TEST NUMBER : 3.5
+ TITLE : PC Availability Status based on SSNM.
+ SUBTITLE : Data Routing from ASP on the basis of PC Availability.
+ PURPOSE: To check that the Data Message from the ASP is routed
to the SG through which the PC is available.
+ TEST CONFIGURATION: K, SG1 and SG2 are in Broadcast.
+ PRE-TEST CONDITIONS: SCTP association is established between SGP1,
SGP2, SGP3, SGP4 and ASP. ASP is Active for RC P in all SGPs.
Also arrange the data in ASP such that SU sends a MTP-Transfer
Indication primitive to M3UA containing the RC value P and
N/w Appearance A. Also arrange Data at SGPs to send SSNM for PC Y
and N/w Appearance A. Route to PC Y is available from both SG1
and SG2. SG Redundancy mode for ASP is Loadshare.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SU
ASP is Active in all SGPs.
<----------- MTP-Transfer Req
DPC Y & CIC S
To SGP1 <--------------- DATA
To SGP2 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC T
To SGP3 <--------------- DATA
To SGP4 <--------------- DATA
From SGP1
DUNA --------------->
(for PC Y)
<----------- MTP-Transfer Req
DPC Y & CIC S
To SGP3 <--------------- DATA
To SGP4 <--------------- DATA
Anshoo Sharma, HSS [Page 146]
Internet Draft M3UA Conformance Test Plan Jan 2003
<----------- MTP-Transfer Req
DPC Y & CIC T
To SGP3 <--------------- DATA
To SGP4 <--------------- DATA
From SGP2
DAVA --------------->
(for PC Y)
From SGP3
DRST --------------->
(for PC Y)
<----------- MTP-Transfer Req
DPC Y & CIC S
To SGP1 <--------------- DATA
To SGP2 <--------------- DATA
<----------- MTP-Transfer Req
DPC Y & CIC T
To SGP1 <--------------- DATA
To SGP2 <--------------- DATA
From SGP1
DUNA --------------->
(for PC Y)
MTP-Pause Ind ----------->
<----------- MTP-Transfer Req
DPC Y
To SGP3 <--------------- DATA
To SGP4 <--------------- DATA
TEST DESCRIPTION:
1. Send two MTP-Transfer Request Primitive from the SU at ASP side
with CIC values S and T respectively. It is assumed that load
sharing across the streams is CIC based.
2. Check A: DATA message 1 reaches SGP1 and SGP2, and Data Message 2
reaches SGP3 and SGP4.
3. Send a DUNA from SGP1 to ASP with Affected Point Code as Y.
4. Repeat the Step1 with appropriate CIC values (S,T) for loadsharing.
5. Check B: Data Message 1 as well as Data Message 2 are both received
SGP3 as well as SGP4.
6. Send a DAVA from SGP2 to ASP with Affected Point Code as Y and
a DRST from SGP3 to ASP with Affected Point Code as Y.
7. Repeat the Step1 with appropriate CIC values (S,T) for loadsharing.
Anshoo Sharma, HSS [Page 147]
Internet Draft M3UA Conformance Test Plan Jan 2003
8. Check C: DATA message 1 reaches SGP1 and SGP2, and Data Message 2
reaches SGP1 and SGP2.
9. Send a DUNA from SGP1 to ASP with Affected Point Code as Y.
10.MTP-Pause Ind for Point Code Y would be received at ASP.
11.Send Data for Point Code Y.
12.Check B: Data Message will be received at SGP3 as well as SGP4.
Note: How the messages will be loadshared based on CIC and SLS is
implementation dependent.
Anshoo Sharma, HSS [Page 148]
Internet Draft M3UA Conformance Test Plan Jan 2003
5.4 ASPSM
Test Cases to test ASPSM Procedures.
"ASPUP-Ack message is not received in response to ASPUP message"
+ TEST NUMBER : 4.1
+ TITLE : ASP management
+ SUBTITLE : ASP-Up-Ack is not received in response to ASPUP message
+ PURPOSE: To check that if Ack message is not received in response to
the ASPUP message then ASP keeps on sending ASPUP message at an
interval for some time and after some tries will report the SM.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. Also arrange the data in ASP such that SM sends ASP Up primitive
to the M3UA. Arrange data in SGP such that Ack message
is not sent in response to the ASPUP message.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
<----------- ASP-Up
<------------ ASPUP
|
|time t1
<------------ ASPUP
|
|time t1
<------------ ASPUP
.
. n tries
.
Status Ind ---------->
TEST DESCRIPTION:
1. Send ASP-Up primitive from SM at ASP. ASP will send ASPUP message to
the SGP. Don't send Ack message from the SGP.
2. Check A: ASPUP message will be retransmitted to the SGP.
Anshoo Sharma, HSS [Page 149]
Internet Draft M3UA Conformance Test Plan Jan 2003
3. Check B: The ASPUP Message will be retransmitted as many times as
has been configured in the implementation
4. Check C: After Maximum number of retries, the ASP UP Ind with
Negative Ind would be received at SM.
5. Repeat the above test case for ASPDN message also
i.e. Ack message is not sent in response to ASPDN message.
Note: This case is implementation specific. In some implementation
there may not be any retransmission. Also the time for which it
will be retransmitted is implementation specific.
Anshoo Sharma, HSS [Page 150]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASP-Down-Ack message is received in ASP-INACTIVE state"
+ TEST NUMBER : 4.2
+ TITLE : ASP management
+ SUBTITLE : ASP-Down-Ack is received in ASP-INACTIVE State
+ PURPOSE: To check that if Down-Ack message is received in
ASP-INACTIVE state, the ASP should move to Down State
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. Arrange data in SGP such that ASP-Down-Ack message is sent to
the ASP.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
ASP is Inactive
ASP-Dn-Ack ------------>
Status Ind ----------> ASP is Down
TEST DESCRIPTION:
1. Check A: ASP is in Inactive State.
1. Send ASP-Down-Ack from SGP.
2. Check B: ASP gives a Status Ind to SM indicating that it's state
has changed to Down.
Anshoo Sharma, HSS [Page 151]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASP-Up-Ack is received in response to ASPDN message"
+ TEST NUMBER : 4.3
+ TITLE : Invalid Message Handling
+ SUBTITLE : ASP-Up-Ack is received in response to ASPDN message
+ PURPOSE: To check that if ASP-Up-Ack message is received in
response to the ASPDN then the Ack message is discarded and ASPDN is
sent again.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is Up. Arrange data in SGP such that ASP-Up-Ack is sent
to ASP in response to ASPDN message with routing context P on stream
0.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
ASP is Inactive
<--------- ASP-Down
<----------- ASPDN
ASP-Up-Ack ------------>
<----------- ASPDN
TEST DESCRIPTION:
1. Send ASP-Down Primitive to the ASP. ASPDN message will be sent to
the SGP.
2. Send ASP-Up-Ack message in response to the ASPDN message.
3. Check A: ASPDN message is received again at the SGP.
4. Repeat the above test case if Ack message is sent.
Anshoo Sharma, HSS [Page 152]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Heartbeat and Heartbeat Ack"
+ TEST NUMBER : 4.4
+ TITLE : AS management
+ SUBTITLE : Heartbeat
+ PURPOSE: : To check that if an ASP sends a BEAT message and does not
receive a Beat Ack then it considers the communication with M3UA Peer
to be Down. Also the ASP sends a BEAT Ack in response to BEAT
message.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is active. Also arrange the data in SGP and ASP such that
BEAT message is sent to the Peer.
EXPECTED MESSAGE SEQUENCE:
SGP ASP SM
a) <----------------- BEAT (ASP)
| Timer 2*T(beat)
| is started
BEAT Ack ---------------->
b) <----------------- BEAT (ASP)
| Timer 2*T(beat)
| is started
|
Timer 2*T(beat) is expired and no BEAT ACK is from SGP.
TEST DESCRIPTION:
1. Send BEAT Message from ASP to the SGP.
2. The beat message should be acknowledged by BEAT ACK before the Timer
expires.
3. Send the Beat message again.
4. The timer expires and no beat ack message is received, the ASP will
consider remote M3UA peer as Down. Transmission of BEAT message is
stopped and ASP-Up procedures are used to re-establish communication
with the SGP M3UA peer.
5. Repeat the Test with SGP sending the BEAT message.
Anshoo Sharma, HSS [Page 153]
Internet Draft M3UA Conformance Test Plan Jan 2003
5.5 ASPTM
Test Cases to test ASPTM Procedures.
"ASP Management messages towards SG"
+ TEST NUMBER : 5.1
+ TITLE : AS management
+ SUBTITLE : ASP Management messages towards SG
+ PURPOSE: To check that if SM sends primitive to send ASP management
messages to the SG then the corresponding message is sent to the SGP.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SG and
ASP. ASP is active. Also arrange the data in ASP such that SM sends
different ASP status primitive to the ASP with valid parameters.
EXPECTED MESSAGE SEQUENCE :
SG ASP SM
<--------- ASP-Inactive
<------------ ASPIA
ASP-Inactive-Ack ------------>
NTFY (AS-Inactive)------------>
Status Ind --------->
<--------- ASP-Down
<------------ ASPDN
ASP-Down-Ack ------------>
<--------- ASP-Up
<------------ ASPUP
ASP-Up-Ack ------------>
NTFY (AS-Inactive)------------>
Anshoo Sharma, HSS [Page 154]
Internet Draft M3UA Conformance Test Plan Jan 2003
Status Ind --------->
<--------- ASP-Active
<------------ ASPAC
ASP-Active-Ack ------------>
NTFY (AS-Active) ------------>
Status Ind --------->
TEST DESCRIPTION:
1. Send ASP-Inactive Primitive from SM in ASP to M3UA.
2. Check A: ASPIA message will be received at the SGP.
3. Send ASP-Inactive-Ack and NTFY(AS-Inactive) in response to the ASPIA
message on stream 0.
4. Check B: ASPM messages are sent on stream 0.
5. Repeat the test case for other primitives like ASP-Down, ASP-Up, and
ASP-Active . ASPDN, ASPUP and ASPAC messages will be sent from
ASP to SGP with parameters passed from SM.
6. Repeat the above test case if Ack messages are sent on stream other
than 0.
Anshoo Sharma, HSS [Page 155]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASP-Active-Ack is received in response to ASPIA message"
+ TEST NUMBER : 5.2
+ TITLE : Invalid Message Handling
+ SUBTITLE : ASP-Active-Ack is received in response to ASPIA message
+ PURPOSE: To check that if ASP-Active-Ack message is received in
response to the ASPIA then the Ack message is discarded and ASPIA is
sent again.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP and ASP is active. Arrange the data in SGP such that
ASP-Active-Ack with routing context P is sent to ASP in response to
ASPIA message on stream 0.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
ASP is active
<--------- ASP-Inactive
<----------- ASPIA
ASP-Active-Ack ------------>
<----------- ASPIA
TEST DESCRIPTION:
1. Send ASP-Inactive Primitive to the ASP. ASPIA message will be sent
to the SGP.
2. Send ASP-Active-Act message in response to the ASPIA message.
3. Check A: ASPIA message is received again at the SGP.
4. Repeat the above test case if ASP-Up-Ack is received in
response to the ASPIA message.
Anshoo Sharma, HSS [Page 156]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASP-Down-Ack is received in ASP Active/Inactive State"
+ TEST NUMBER : 5.3
+ TITLE : Invalid Message Handling
+ SUBTITLE : ASP-Down-Ack is received in ASP Active/Inactive State.
+ PURPOSE: To check that if ASP-Down-Ack message is received in
any state, the state of the ASP changes to Down.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP is Active/Inactive. Arrange the data in SGP such that
ASP-Down-Ack is sent to ASP on stream 0.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
ASP is Active/Inactive
ASP-Down-Ack ------------>
Status Ind ---------> ASP is Down
TEST DESCRIPTION:
1. Send ASP-Down-Ack Message from SGP.
2. Check A: Status Ind with ASP State a Down is received at ASP.
Anshoo Sharma, HSS [Page 157]
Internet Draft M3UA Conformance Test Plan Jan 2003
"Multiple ASP-Active-Ack are received in response to ASP Active"
+ TEST NUMBER : 5.4
+ TITLE : Invalid Message Handling
+ SUBTITLE : Multiple ASP-Active-Ack are received in response to
a single ASP Active Message.
+ PURPOSE: To Check that ASP successfully processes RCs spread
over Multiple ASP Active Ack Messages.
+ TEST CONFIGURATION: I
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP is Inactive. Arrange the data in SGP such that ASP-Active-Ack
with RC value P or Q are sent to ASP on stream 0.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
ASP is Inactive
<--------- ASP-Active
<------------ ASPAC (RC P, RC Q)
ASP-Active-Ack ------------>
(RC P)
NTFY (AS-Active) ------------>
(RC P) | Status Ind --------->
|
| Timer Expires
<------------ ASPAC (only RC Q)
ASP-Active-Ack ------------>
(RC Q)
NTFY (AS-Active) ------------>
(RC Q)
Status Ind --------->
TEST DESCRIPTION:
1. Invoke ASP Active Primitive from ASP with RC value as P and Q.
2. Check A: ASPAC is received at SGP with Routing Contexts P and Q.
3. Send ASP Active Ack and NTFY from SGP with only one RC value P.
Anshoo Sharma, HSS [Page 158]
Internet Draft M3UA Conformance Test Plan Jan 2003
4. Check B: Status Ind for RC P is received at ASP and after
time-out ASPAC is retransmitted with just one RC = Q.
5. Send ASP Active Ack and NTFY from SGP with only one RC value Q.
6. Check C: Status Ind for RC P is received at ASP.
Note: In some Implementations Retransmission is not done. Here a
negative Indication to the SM would be given regarding RC Q and
no ASPAC will not be resent.
Anshoo Sharma, HSS [Page 159]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASPAC-Ack message is not received in response to ASPAC message"
+ TEST NUMBER : 5.5
+ TITLE : ASP management
+ SUBTITLE : ASP-Active-Ack is not received in response to ASPAC
message.
+ PURPOSE: To check that if Ack message is not received in response to
the ASPAC message then ASP keeps on sending ASPAC message at an
interval for some number of max retries and will then report to SM.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. Also arrange the data in ASP such that SM sends ASP Active
primitive to the M3UA. Arrange data in SGP such that Ack message
is not sent in response to the ASPUP message.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
<----------- ASP-Up
<------------ ASPAC
|
|time t1
<------------ ASPAC
|
|time t1
<------------ ASPAC
.
. n tries
.
Status Ind ---------->
TEST DESCRIPTION:
1. Send ASP-Active primitive from SM at ASP. ASP will send ASPUP
message to the SGP. Don't send Ack message from the SGP.
2. Check A: ASPAC message will be retransmitted to the SGP.
3. Check B: The ASPAC Message will be retransmitted as many times as
has been configured in the implementation.
4. Check C: After Maximum number of retries, the ASP Active Ind with
Negative Ind would be received at SM.
Anshoo Sharma, HSS [Page 160]
Internet Draft M3UA Conformance Test Plan Jan 2003
5. Repeat the above test case for ASPIA message also.
i.e. Ack message is not sent in response to ASPIA message.
Note: This case is implementation specific. In some implementation
there may not be any retransmission. Also the time for which it
will be retransmitted is implementation specific.
Anshoo Sharma, HSS [Page 161]
Internet Draft M3UA Conformance Test Plan Jan 2003
"ASP-Inactive-Ack is received in ASP Active State"
+ TEST NUMBER : 5.6
+ TITLE : Invalid Message Handling
+ SUBTITLE : ASP-Inactive-Ack is received in ASP Active State.
+ PURPOSE: To check that if ASP-Inactive-Ack message is received in
Active state, the state of the ASP changes to Inactive.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP is Active for RC P. Arrange the data in SGP such that
ASP-Inactive-Ack for RC P is sent to ASP.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
ASP is Active
ASP-Inactive-Ack ------------>
Status Ind ---------> ASP is Inactive
TEST DESCRIPTION:
1. Send ASP-Inactive-Ack Message for RC P from SGP.
2. Check A: Status Ind with ASP State as Inactive for RC P
is received at ASP.
Anshoo Sharma, HSS [Page 162]
Internet Draft M3UA Conformance Test Plan Jan 2003
5.6 SCTP Connection Management
Test Cases to test SCTP Connection Management
"SCTP Connection Establishment"
+ TEST NUMBER : 6.1
+ TITLE : SCTP Connection Management
+ SUBTITLE : SCTP Connection Establishment
+ PURPOSE: To check that on receiving M-SCTP-Establish primitive from
SM, ASP initiates and establishes an SCTP association with the SGP.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is not established between SGP
and ASP. Also arrange the data in ASP such that SM sends
M-SCTP-Establish primitive to M3UA with the SGP id to which the
connection is to be established.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SU + SM
<--------- M-SCTP-Establish Request
<------------------->
SCTP association will be established by SCTP
ASP will receive Communication-Up primitive from SCTP
M-SCTP-Establish Ind------->
TEST DESCRIPTION:
1. Send M-SCTP-Establish Request Primitive from the SM at ASP side to
establish an SCTP association with the SGP.
2. Check A: SCTP association will be established and M-SCTP-Establish
indication will be received at the SM.
Anshoo Sharma, HSS [Page 163]
Internet Draft M3UA Conformance Test Plan Jan 2003
"SCTP Connection Termination"
+ TEST NUMBER : 6.2
+ TITLE : SCTP Connection Management
+ SUBTITLE : SCTP Connection Termination
+ PURPOSE: To check that on receiving SCTP-Communication Down
indication primitive from SCTP, ASP will send the M-SCTP Status
primitive to the upper layer.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is in Inactive state. Also arrange the data in SGP such that
SCTP association is terminated between SGP and ASP.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM + SU
ASP is Inactive
<-------------- ASPDN
ASP-Down-Ack -------------->
SCTP association is terminated
ASP will receive Communication-Down primitive from SCTP
M-SCTP Status -------->
<-------- MTP-Transfer
Send Failure --------->
TEST DESCRIPTION:
1. Terminate the association between SGP and ASP.
2. Check A: SCTP association will be down and on receiving
Communication Down primitive from SCTP, M-SCTP Status indication
will be received at the SM.
3. Check B: State of ASP will be down. Send MTP-Transfer primitive from
the SU to send some Protocol DATA. ASP will report send failure.
Note: It may be possible that SCTP connection is terminated without
exchanging the ASPDN message.
Anshoo Sharma, HSS [Page 164]
Internet Draft M3UA Conformance Test Plan Jan 2003
"SCTP Connection Restart"
+ TEST NUMBER : 6.3
+ TITLE : SCTP Connection Management
+ SUBTITLE : SCTP Connection Restart
+ PURPOSE: To check that on receiving SCTP-Communication Restart
Indication primitive from SCTP, ASP will send the M-SCTP Status
primitive to the upper layer.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP and
ASP. ASP is in active state. Also arrange in SGP such that SCTP
association is restarted between SGP and ASP.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM + SU
ASP is active
ASP will receive Communication-Restart Primitive from SCTP
M-SCTP Status -------->
Status Ind --------> ASP Down
Pause Ind -------->
(PC Z)
<-------- MTP-Transfer
Send Failure --------->
TEST DESCRIPTION:
1. Invoke a Connection Restart on the association between SGP and ASP.
2. Check A: SCTP association will be restarted and on receiving
Communication Restart primitive from SCTP, M-SCTP Status indication
and an ASP Status Ind will be received at the SM.
3. Check B: State of ASP will be Down. Send MTP-Transfer primitive from
the SU to send some Protocol DATA. ASP will report send failure.
Anshoo Sharma, HSS [Page 165]
Internet Draft M3UA Conformance Test Plan Jan 2003
"SCTP Connection Establishment"
+ TEST NUMBER : 6.4
+ TITLE : SCTP Connection Management
+ SUBTITLE : SCTP Connection Establishment
+ PURPOSE: To check that on receiving Communication Up primitive from
SCTP, SG M3UA will send M-SCTP-Establish indication to the SM.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is not established between SGP
and ASP1. Also arrange the data in ASP such that SCTP association is
established between ASP1 and SGP.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SM
SCTP Establish request to SCTP
SCTP association will be established by SCTP
ASP will receive Communication-Up primitive from SCTP
M-SCTP-Establish Ind ------->
<--------- ASP-UP
<------------------ ASPUP
ASP-Up-Ack ------------------>
NTFY ------------------>
(AS-Inactive)
Status Ind --------->
TEST DESCRIPTION:
1. Make an SCTP association between SGP and ASP. ASP will receive
Communication Up primitive from SCTP.
2. Check A: SM receives M-SCTP-Establish indication.
3. Send ASPUP message from ASP to SGP.
4. Send ASP-Up-Ack and NTFY message with status ASP-Inactive from
the SGP.
5. Check B: Status Ind for ASP State as Inactive is received at SM.
Anshoo Sharma, HSS [Page 166]
Internet Draft M3UA Conformance Test Plan Jan 2003
5.7 Dynamic Routing Key (RK) Management
Test Cases to test Dynamic RK Management Procedures.
"RK Registration Request"
+ TEST NUMBER : 7.1
+ TITLE : RK Registration Request.
+ SUBTITLE : RK Registration is sent on Registration request by SM.
+ PURPOSE: To check that when SM invokes Registration Request a
valid REG_REQ message is sent to the SGP.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP
and ASP. ASP is Inactive in SGP. Also arrange the data in ASP
such that SU sends a Reg Req Primitive to M3UA containing a
valid Routing Key (Indicator). Also arrange Data at SGPs to send
REG RESP with a RC value.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SU
ASP is Inactive in SGP.
<----------- REG REQ (RK = RK1)
To SGP <--------------- REG_REQ (RK1)
REG_RSP --------------->
(RC1) REG RESPONSE ----------->
TEST DESCRIPTION:
1. Invoke RK Registration Request SM API with a valid Routing Key.
2. Check A: A REG_REQ Message with RK1 packed is sent from the
ASP to SGP.
3. Send a REG_RSP with SUCCESS and RC Value RC1 from the SGP to
the ASP.
4. Check B: A Registration Success Response is sent to the SM
at ASP.
Anshoo Sharma, HSS [Page 167]
Internet Draft M3UA Conformance Test Plan Jan 2003
"RK Deregistration Request"
+ TEST NUMBER : 7.2
+ TITLE : RK Deregistration Request.
+ SUBTITLE : RK Deregistration is sent on Deregistration request by SM.
+ PURPOSE: To check that when SM invokes Deregistration Request a
valid DEREG_REQ message is sent to the SGP.
+ TEST CONFIGURATION: G
+ PRE-TEST CONDITIONS: SCTP association is established between SGP
and ASP. ASP is Inactive in SGP. Also arrange the data in ASP
such that SU sends a Dereg Req Primitive to M3UA containing a
valid Routing Context. Also arrange Data at SGPs to send
DEREG RESP with a RC value.
EXPECTED MESSAGE SEQUENCE :
SGP ASP SU
ASP is Inactive in SGP.
<----------- DEREG REQ (RC = RC1)
To SGP <--------------- DEREG_REQ (RC1)
DEREG_RSP --------------->
(RC1)
DEREG RESPONSE ----------->
TEST DESCRIPTION:
1. Invoke RK Deregistration Request SM API with a valid
Routing Context.
2. Check A: A DEREG_REQ Message with RC1 is sent from the
ASP to SGP.
3. Send a DEREG_RSP with SUCCESS and RC Value RC1 from the SGP to
the ASP.
4. Check B: A Deregistration Success Response is sent to the SM
at ASP.
Anshoo Sharma, HSS [Page 168]
Internet Draft M3UA Conformance Test Plan Jan 2003
6. Acknowledgements
The author would like to thank (in alphabetical order)
Akhtar Iqbal
Anjali Gurmukhani
Dipak Aggarwal
Harsh Bhondwe
Kamesh Kaul
Vipin Gupta
for their insightful comments and suggestions.
Funding for the RFC editor function is currently provided by the
Internet Society.
7. Authors' Addresses
Anshoo Sharma
Hughes Software Systems
Electronic City, Plot 17,
Sector 18, Gurgaon 122015
Harayana, India
EMail: [email protected]
8. References
[M3UA] RFC 3332 "SS7 MTP3-User Adaptation Layer (M3UA)"
[2960] RFC 2960 "Stream Control Transport Protocol"
R. Stewart, et al, November 2000.
[ITU-MTP] ITU-T Recommendations Q.701-Q.705, 'Signaling System
No. 7 (SS7) - Message Transfer Part (MTP)'
[M3UA-CONF] Test Specification for MTP3 User Adaptation
<draft-mahajan-test-spec-m3ua-00.txt> July 2000,
Work in Progress.
Anshoo Sharma, HSS [Page 169]
Internet Draft M3UA Conformance Test Plan Jan 2003
Copyright Statement
Copyright (C) The Internet Society (2001). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph
are included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
THIS DOCUMENT AND THE INFORMATION CONTAINED HEREIN IS PROVIDED ON AN
"AS IS" BASIS AND THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Anshoo Sharma, HSS [Page 170]
| ||||||||||||||||
| Last modified: Thu, 28 Nov 2024 02:49:28 GMT Copyright © 2014 OpenSS7 Corporation All Rights Reserved. | |||||||||||||||||