iperf Manual

A PDF version of this document is available here.

OpenSS7 IPERF Utility

OpenSS7 IPERF Utility Installation and Reference Manual

About This Manual

This is Edition 8, last updated 2008-10-31, of The OpenSS7 IPERF Utility Installation and Reference Manual, for Version 2.0 release 8 of the OpenSS7 IPERF Utility package.

Preface

Notice

This package is released and distributed under the AGPL (see GNU Affero General Public License). Please note, however, that there are different licensing terms for the manual pages and some of the documentation (derived from OpenGroup¹ publications and other sources). Consult the permission notices contained in the documentation for more information.

Also note that portions of this software is derived from software developed by the University of Illinois covered under the UI License (see University of Illinois License).

This manual is released under the FDL (see GNU Free Documentation License) with no sections invariant.

Abstract

This manual provides a Installation and Reference Manual for OpenSS7 IPERF Utility.

Objective

The objective of this manual is to provide a guide for the network programmer when developing application programs for OpenSS7 IPERF Utility.

This guide provides information to developers on the use of the OpenSS7 IPERF Utility at user level.

Intent

The intent of this manual is to act as an introductory guide to the STREAMS programmer. It is intended to be read alone and is not intended to replace or supplement the OpenSS7 IPERF Utility manual pages. For a reference for writing code, the manual pages (see STREAMS(9)) provide a better reference to the programmer. Although this describes the features of the OpenSS7 IPERF Utility package, OpenSS7 Corporation is under no obligation to provide any software, system or feature listed herein.

Audience

This manual is intended for a highly technical audience. The reader should already be familiar with Linux network programming, the Linux file system, character devices, driver input and output, interrupts, software interrupt handling, scheduling, process contexts, multiprocessor locks, etc.

The guide is intended for network and systems programmers, who use the OpenSS7 IPERF Utility mechanism at user level for Linux and UNIX system communication services.

Readers of the guide are expected to possess prior knowledge of the Linux and UNIX system, programming, networking, and data communication.

Revisions

Take care that you are working with a current version of this manual: you will not be notified of updates. To ensure that you are working with a current version, contact the Author, or check The OpenSS7 Project website for a current version.

A current version of this manual is normally distributed with the OpenSS7 IPERF Utility package.

Version Control

     iperf.texi,v
     Revision 0.9.2.13  2008-09-20 11:04:24  brian
     - added package patchlevel
     
     Revision 0.9.2.12  2008-08-03 06:03:27  brian
     - protected agains texinfo commands in log entries
     
     Revision 0.9.2.11  2008/07/27 08:48:44  brian
     - no invariant sections, more libtool ignores
     
     Revision 0.9.2.10  2008-04-25 11:50:42  brian
     - updates to AGPLv3
     
     Revision 0.9.2.9  2007/08/12 06:43:41  brian
     - updated licenses in manuals
     
     Revision 0.9.2.8  2007/06/22 00:18:23  brian
     - mostly documentation updates for release, some netconfig workaround
     
     Revision 0.9.2.7  2007/02/28 06:30:18  brian
     - updates and corrections, #ifdef instead of #if
     
     Revision 0.9.2.6  2006/09/18 01:06:17  brian
     - updated manuals and release texi docs
     
     Revision 0.9.2.5  2006/08/28 10:46:53  brian
     - correction
     
     Revision 0.9.2.4  2006/08/28 10:32:44  brian
     - updated references
     
     Revision 0.9.2.3  2006/08/27 12:26:30  brian
     - finalizing auto release files
     
     Revision 0.9.2.2  2006/08/26 18:31:34  brian
     - handle long urls
     
     Revision 0.9.2.1  2006/08/26 14:41:37  brian
     - added manual

ISO 9000 Compliance

Only the TeX, texinfo, or roff source for this manual is controlled. An opaque (printed, postscript or portable document format) version of this manual is an UNCONTROLLED VERSION.

Disclaimer

OpenSS7 Corporation disclaims all warranties with regard to this documentation including all implied warranties of merchantability, fitness for a particular purpose, non-infringement, or title; that the contents of the manual are suitable for any purpose, or that the implementation of such contents will not infringe on any third party patents, copyrights, trademarks or other rights. In no event shall OpenSS7 Corporation be liable for any direct, indirect, special or consequential damages or any damages whatsoever resulting from loss of use, data or profits, whether in an action of contract, negligence or other tortious action, arising out of or in connection with any use of this manual or the performance or implementation of the contents thereof.

OpenSS7 Corporation reserves the right to revise this software and documentation for any reason, including but not limited to, conformity with standards promulgated by various agencies, utilization of advances in the state of the technical arts, or the reflection of changes in the design of any techniques, or procedures embodied, described, or referred to herein. OpenSS7 Corporation is under no obligation to provide any feature listed herein.

U.S. Government Restricted Rights

If you are licensing this Software on behalf of the U.S. Government ("Government"), the following provisions apply to you. If the Software is supplied by the Department of Defense ("DoD"), it is classified as "Commercial Computer Software" under paragraph 252.227-7014 of the DoD Supplement to the Federal Acquisition Regulations ("DFARS") (or any successor regulations) and the Government is acquiring only the license rights granted herein (the license rights customarily provided to non-Government users). If the Software is supplied to any unit or agency of the Government other than DoD, it is classified as "Restricted Computer Software" and the Government's rights in the Software are defined in paragraph 52.227-19 of the Federal Acquisition Regulations ("FAR") (or any successor regulations) or, in the cases of NASA, in paragraph 18.52.227-86 of the NASA Supplement to the FAR (or any successor regulations).

Acknowledgements

As with most open source projects, this project would not have been possible without the valiant efforts and productive software of the Free Software Foundation and the Linux Kernel Community.

Contributors

The primary contributor to the OpenSS7 OpenSS7 IPERF Utility package is Brian F. G. Bidulock. The following is a list of significant contributors to The OpenSS7 Project:

	− Per Berquist
	− John Boyd
	− Chuck Winters
	− Peter Courtney
	− Tom Chandler
	− Gurol Ackman
	− Kutluk Testicioglu
	− John Wenker
	− Others

Additional thanks to:

	• National Laboratory for Applied Network Research
	• National Center for Supercomputing Applications
	• University of Illinois at Urbana-Champaign

Authors

The authors of the OpenSS7 OpenSS7 IPERF Utility package include:

− Brian Bidulock

See Author Index, for a complete listing and cross-index of authors to sections of this manual.

Maintainer

The maintainer of the OpenSS7 OpenSS7 IPERF Utility package is:

− Brian Bidulock

Please send bug reports to [email protected] using the send-pr script included in the package, only after reading the BUGS file in the release, or See Problem Reports.

Web Resources

The OpenSS7 Project provides a website dedicated to the software packages released by the OpenSS7 Project.

Bug Reports

Please send bug reports to [email protected] using the send-pr script included in the OpenSS7 IPERF Utility package, only after reading the BUGS file in the release, or See Problem Reports. You can access the OpenSS7 GNATS database directly via the web, however, the preferred method for sending new bug reports is via mail with the send-pr script.

Mailing Lists

The OpenSS7 Project provides a number of general discussion Mailing Lists for discussion concerning the OpenSS7 OpenSS7 IPERF Utility package as well as other packages released by The OpenSS7 Project.

These are mailman mailing lists and so have convenient web interfaces for subscribers to control their settings. See http://www.openss7.org/mailinglist.html.

The mailing lists are as follows:

openss7: The openss7 mailing list is for general enquiries, information exchange and announcements regarding the OpenSS7 Project. This is our original mailing list and takes the highest amount of traffic.
openss7-announce: The openss7-announce mailing list is for announcements related to the OpenSS7 Project. This list will accept announcements posted by subscribers. Subscribe to this list if you are interested in announcements from the OpenSS7 Project, subscribers and sponsors, related to the OpenSS7 Project or STREAMS, SS7, SIGTRAN or SCTP in general.
openss7-cvs: The openss7-cvs mailing list is for automatic CVS log reporting. You must get permission of the owner to subscribe to this list. Subscribers are not allowed to post to this list, this is merely for distributing notification of changes to the CVS repository.h
openss7-develop: The openss7-develop mailing list is for email exchange related to the development projects under the OpenSS7 Project. This includes development requests, proposals, requests for comment or proposal. Subscribe to this list if you are interested in ongoing development details regarding the OpenSS7 Project.
openss7-test: The openss7-test mailing list is for email exchange related to the testing of code under the OpenSS7 Project. This specifically relates to conformance testing, verification testing, interoperability testing and beta testing. Subscribe to this list if you are interested in participating in and receiving ongoing details of test activities under the OpenSS7 Project.
openss7-bugs: The openss7-bugs mailing list is specifically tailored to bug tracking. The mailing list takes a feed from the OpenSS7 GNATS bug tracking system and accepts posting of responses to bug reports, tracking and resolution. Subscribe to this list if you are interested in receiving detailed OpenSS7 release code bug tracking information. This list is not archived; for historical information on problem reports, see our GNATS databases.
openss7-updates: The openss7-updates mailing list provides updates on OpenSS7 Project code releases and ongoing activities. Subscribers are not allowed to post to this list; this list is for official OpenSS7 Project announcements only. Subscribe to this list if you are interested in receiving updates concerning official releases and activities of the OpenSS7 Project.
openss7-streams: The openss7-streams mailing list is for email exchange related to the STREAMS development projects under the OpenSS7 Project. This includes development requests, proposals, requests for comment or proposal. Subscribe to this list if you are interested in ongoing development details regarding the OpenSS7 Project STREAMS components.
linux-streams: The linux-streams mailing list is for mail exchange related to Linux Fast-STREAMS or Linux STREAMS. This includes patches, development requests, proposals, requests for comment or proposal. Subscribe to this list if you are interested in ongoing development details regarding the STREAMS for Linux components. This is the the new (September 2006) home of the linux-streams list formerly of <gsyc.escet.urjc.es>.

Spam

To avoid spam being sent to the members of the OpenSS7 mailing list(s), we have blocked mail from non-subscribers. Please subscribe to the mailing list before attempting to post to them. (Attempts to post when not subscribed get bounced.)

As an additional measure against spam, subscriber lists for all OpenSS7 mailing lists are not accessible to non-subscribers; for most lists subscriber lists are only accessible to the list administrator. This keeps your mailing address from being picked off our website by bulk mailers.

Acceptable Use Policy

It is acceptable to post professional and courteous messages regarding the OpenSS7 package or any general information or questions concerning STREAMS, SS7, SIGTRAN, SCTP or telecommunications applications in general.

Large Attachments

The mailing list is blocked from messages of greater than 40k. If you have attachments (patches, test programs, etc.) and you mail them to the list, it will bounce to the list administrator. If you are interested in making your patches, test programs, test results or other large attachments available to the members of the mailing list, state in the message that you would like them posted and the list administrator will place them in the mail archives.

Quick Start Guide

OpenSS7 IPERF Utility

Package iperf-2.0.8 was released under AGPLv3 2008-10-31.

Iperf is a general purpose tool for measuring bandwidth and performance of the Internet Protocol suite. The OpenSS7 Modified OpenSS7 IPERF Utility package is an OpenSS7 Project release of the DAST iperf package configured to run with OpenSS7 Linux Native Stream Control Transmission Protocol (SCTP).

The OpenSS7 IPERF Utility package provides primarily the iperf(1), C++ Language program that acts as either an Iperf server or client for testing connections and networking. The iperf(1) program is executed on one host in server mode and then executed on another host in client mode. Characteristics of the connection or association can be altered when formed. Reporting formats and sample intervals can also be altered when the connection or association is formed.

This is a fork of the Iperf package released by the University of Illinois modified by the OpenSS7 Project for use with OpenSS7 SCTP (Stream Control Transmission Protocol). This OpenSS7 release of the package is based on the Iperf-2.0.0 release from the University of Illinois.

Modifications to the package are derived from the OpenSS7 SCTP implementation and are released under the GNU Affero General Public License (AGPL) Version 3. The Iperf tool itself is licensed under specific terms by the University of Illinois. Please see LICENSES for the University of Illinois Iperf copyright notices and licensing restrictions. The Iperf tool is:

Copyright 1999, 2000, 2001, 2002, 2003, 2004
The Board of Trustees of the University of Illinois
All rights reserved

See University of Illinois License in the LICENSES file for complete details.

Please note that this modified version of the Iperf package is not endorsed by the University of Illinois or DAST in any way and that neither the original copyright holders nor OpenSS7 Corporation will take any responsibility in it.

This distribution is only currently applicable to Linux 2.4 kernels and was targeted at ix86, x86_64, ppc and ppc64 architectures, but should build and install for other architectures as well.

Release

This is the iperf-2.0.8 package, released 2008-10-31. This ‘2.0.8’ release, and the latest version, can be obtained from the download area of The OpenSS7 Project website using a command such as:

     $> wget http://www.openss7.org/tarballs/iperf-2.0.8.tar.bz2

The release is available as an autoconf(1) tarball, src.rpm or dsc, as a set of binary rpms or debs, or as a yum(8) or apt(8) repository. See the download page for the autoconf(1) tarballs, src.rpms, dscs, or repository access instructions. See the iperf package page for tarballs, source and binary packages.

Please see the NEWS file for release notes and history of user visible changes for the current version, and the ChangeLog file for a more detailed history of implementation changes. The TODO file lists features not yet implemented and other outstanding items.

Please see the INSTALL, INSTALL-iperf and README-make, files (or see Installation) for installation instructions.

When working from cvs(1) or git(1), please see the README-cvs, file (or see Downloading from CVS). An abbreviated installation procedure that works for most applications appears below.

This release of the package is published strictly under Version 3 of the GNU Affero Public License which can be found in the file COPYING. Package specific licensing terms (if any) can be found in the file LICENSES. Please respect these licensing arrangements. If you are interested in different licensing terms, please contact the copyright holder, or OpenSS7 Corporation <[email protected]>.

See README-alpha (if it exists) for alpha release information.

Prerequisites

The quickest and easiest way to ensure that all prerequisites are met is to download and install this package from within the OpenSS7 Master Package, openss7-0.9.2.G, instead of separately.

Prerequisites for the OpenSS7 IPERF Utility package are as follows:

Linux distribution, somewhat Linux Standards Base compliant, with a 2.4 or 2.6 kernel and the appropriate tool chain for compiling out-of-tree kernel modules. Most recent Linux distributions are usable out of the box, but some development packages must be installed. For more information, see Compatibility.

	− A fairly LSB compliant GNU/Linux distribution.²
	− Linux 2.4 kernel (2.4.10 - 2.4.27), or
	− Linux 2.6 kernel (2.6.3 - 2.6.26);
	− glibc2 or better.
	− GNU groff (for man pages).³
	− GNU texinfo (for info files).

(Note that although the original University of Illinois DAST Iperf builds and installs on a number of operating systems, the OpenSS7 modified version only currently builds and installs on Linux.)

(Note: If you acquired iperf a part of the OpenSS7 Master Package, then the dependencies listed below will already have been met by unpacking the master package.)

OpenSS7 Sockets SCTP, sctp-0.2.27. (Optional.)

When configuring and building multiple OpenSS7 Project release packages, place all of the source packages (unpacked tarballs) at the same directory level and all build directories at the same directory level (e.g. all source packages under /usr/src).

When installing packages that install as kernel modules, it is necessary to have the correct kernel development package installed. For the following distributions, use the following commands:

     Ubuntu:  $> apt-get install linux-headers
     Debian:  $> apt-get install kernel-headers
     Fedora:  $> yum install kernel-devel

You also need the same version of gcc(1) compiler with which the kernel was built. If it is not the default, add ‘CC=kgcc’ on the line after ‘./configure’, for example:

     $> ../iperf-2.0.8/configure CC='gcc-3.4'

Installation

The following commands will download, configure, build, check, install, validate, uninstall and remove the package:

     $> wget http://www.openss7.org/tarballs/iperf-2.0.8.tar.bz2
     $> tar -xjvf iperf-2.0.8.tar.bz2
     $> mkdir build
     $> pushd build
     $> ../iperf-2.0.8/configure --enable-autotest
     $> make
     $> make check
     $> sudo make install
     $> sudo make installcheck
     $> sudo make uninstall
     $> popd
     $> sudo rm -rf build
     $> rm -rf iperf-2.0.8
     $> rm -f iperf-2.0.8.tar.bz2

If you have problems, try building with the logging targets instead. If the make of a logging target fails, an automatic problem report will be generated that can be mailed to The OpenSS7 Project.⁴ Installation steps using the logging targets proceed as follows:

     $> wget http://www.openss7.org/tarballs/iperf-2.0.8.tar.bz2
     $> tar -xjvf iperf-2.0.8.tar.bz2
     $> mkdir build
     $> pushd build
     $> ../iperf-2.0.8/configure --enable-autotest
     $> make compile.log
     $> make check.log
     $> sudo make install.log
     $> sudo make installcheck.log
     $> sudo make uninstall.log
     $> popd
     $> sudo rm -rf build
     $> rm -rf iperf-2.0.8
     $> rm -f iperf-2.0.8.tar.bz2

See README-make for additional specialized make targets.

For custom applications, see the INSTALL and INSTALL-iperf files or the see Installation, as listed below. If you encounter troubles, see Troubleshooting, before issuing a bug report.

Brief Installation Instructions

The OpenSS7 IPERF Utility package is available from the downloads area of The OpenSS7 Project website using a command such as:

     $> wget http://www.openss7.org/tarballs/iperf-2.0.8.tar.bz2

Unpack the tarball using a command such as:

     $> tar -xjvf iperf-2.0.8.tar.bz2

The tarball will unpack into the relative subdirectory named after the package name: iperf-2.0.8.

The package builds using the GNU autoconf utilities and the configure script. To build the package, we recommend using a separate build directory as follows:

     $> mkdir build
     $> cd build
     $> ../iperf-2.0.8/configure

In general, the package configures and builds without adding any special options to the configure script. For general options to the configure script, see the GNU INSTALL file in the distribution:

     $> less ../iperf-2.0.8/INSTALL

For specific options to the configure script, see the INSTALL-iperf file in the distribution, or simply execute the configure script with the --help option like so:

     $> ../iperf-2.0.8/configure --help

After configuring the package, the package can be compiled simply by issuing the ‘make’ command:

     $> make

Some specialized makefile targets exists, see the README-make file in the distribution or simply invoke the ‘help’ target like so:

     $> make help | less

After successfully building the package, the package can be checked by invoking the ‘check’ make target like so:

     $> make check

After successfully checking the package, the package can be installed by invoking the ‘install’ make target (as root) like so:

     $> sudo make install

The test suites that ship with the package can be invoked after the package has been installed by invoking the ‘installcheck’ target. This target can either be invoked as root, or as a normal user, like so:

     $> make installcheck

(Note: you must add the --enable-autotest flag to configure, above for the test suites to be invoked with ‘make installcheck’.)

The package can be cleanly removed by invoking the ‘uninstall’ target (as root):

     $> sudo make uninstall

Then the build directory and tarball can be simply removed:

     $> cd ..
     $> rm -rf build
     $> rm -rf iperf-2.0.8
     $> rm -f iperf-2.0.8.tar.bz2

Detailed Installation Instructions

More detailed installation instructions can be found in the Installation, contained in the distribution in ‘text’, ‘info’, ‘html’ and ‘pdf’ formats:

     $> cd ../iperf-2.0.8
     $> less doc/manual/iperf.txt
     $> lynx doc/manual/iperf.html
     $> info doc/manual/iperf.info
     $> xpdf doc/manual/iperf.pdf

The ‘text’ version of the manual is always available in the MANUAL file in the release.

The current manual is also always available online from The OpenSS7 Project website at:

     $> lynx http://www.openss7.org/iperf_manual.html

1 Introduction

This manual documents the design, implementation, installation, operation and future development schedule of the OpenSS7 IPERF Utility package.

1.1 Overview

This manual documents the design, implementation, installation, operation and future development of the OpenSS7 IPERF Utility package.

1.2 Organization of this Manual

This manual is organized (loosely) into several sections as follows:

Introduction.	This introduction
Objective.	Objective of the package
Reference.	Contents of the package
Conformance.	Conformance of the package
Releases.	Releases of the package
Installation.	Installation of the package
Troubleshooting.	Troubleshooting of the package

1.3 Conventions and Definitions

This manual uses texinfo typographic conventions.

2 Objective

3 Reference

3.1 Files

IPERF installs the following info files in the system info directory, /usr/share/info/:

iperf.info
iperf.info-1
iperf.info-2
iperf.info-3
iperf.info-4: These files contain this manual in GNU info format.

IPERF installs the following manunal page macros and reference database files in the system man directory, /usr/share/man/:⁵

iperf.macros: This file contains manual page macro definitions included by the manual pages included in the package.
iperf.refs: This file contains a reference database referenced by the manual pages included in the package.

3.2 Drivers

3.3 Modules

3.4 Libraries

3.5 Utilities

3.6 Development

4 Conformance

5 Releases

This is the OpenSS7 Release of the OpenSS7 IPERF Utility package, modified for use with OpenSS7 Stream Control Transmission Protocol (SCTP) Linux Native Kernel.

The purpose of providing a separate release of this package was to provide support for SCTP as well as providing the ability to use GNU autoconf tools for maintenance and binary RPM release of the package.

The following sections provide information on OpenSS7 IPERF Utility releases as well as compatibility information of OpenSS7 release to the original UI DAST releases of the OpenSS7 IPERF Utility package.

5.1 Prerequisites

The quickest and easiest way to ensure that all prerequisites are met is to download and install this package from within the OpenSS7 Master Package, openss7-0.9.2.G, instead of separately.

Prerequisites for the OpenSS7 IPERF Utility package are as follows:

	− A fairly LSB compliant GNU/Linux distribution.⁶
	− Linux 2.4 kernel (2.4.10 - 2.4.27), or
	− Linux 2.6 kernel (2.6.3 - 2.6.26);
	− glibc2 or better.
	− GNU groff (for man pages).⁷
	− GNU texinfo (for info files).

(Note that although the original University of Illinois DAST Iperf builds and installs on a number of operating systems, the OpenSS7 modified version only currently builds and installs on Linux.)

(Note: If you acquired iperf a part of the OpenSS7 Master Package, then the dependencies listed below will already have been met by unpacking the master package.)

OpenSS7 Sockets SCTP, sctp-0.2.27. (Optional.)

If you need to rebuild the package from sources with modifications, you will need a larger GNU tool chain as described in See Downloading from CVS.

5.2 Compatibility

This section discusses compatibility with major prerequisites.

5.2.1 GNU/Linux Distributions

OpenSS7 IPERF Utility is compatible with the following Linux distributions:⁸

CentOS Enterprise Linux 3.4 (centos34) TBD
CentOS Enterprise Linux 4.0 (centos4) TBD
CentOS Enterprise Linux 4.92 (centos49) TBD
CentOS Enterprise Linux 5.0 (centos5)
CentOS Enterprise Linux 5.1 (centos51)
CentOS Enterprise Linux 5.2 (centos52)
Debian 3.0r2 Woody (deb3.0) TBD
Debian 3.1r0a Sarge (deb3.1) TBD
Debian 4.0r1 Etch (deb4.0)
Debian 4.0r2 Etch (deb4.0)
Debian 4.0r3 Etch (deb4.0)
Fedora Core 1 (FC1) TBD
Fedora Core 2 (FC2) TBD
Fedora Core 3 (FC3) TBD
Fedora Core 4 (FC4) TBD
Fedora Core 5 (FC5) TBD
Fedora Core 6 (FC6) TBD
Fedora 7 (FC7)
Fedora 8 (FC8)
Fedora 9 (FC9)
Gentoo 2006.1 (untested) TBD
Gentoo 2007.1 (untested) TBD
Lineox 4.026 (LEL4) TBD
Lineox 4.053 (LEL4) TBD
Mandrakelinux 9.2 (MDK92) TBD
Mandrakelinux 10.0 (MDK100) TBD
Mandrakelinux 10.1 (MDK101) TBD
Mandriva Linux LE2005 (MDK102) TBD
Mandriva Linux LE2006 (MDK103) TBD
Mandriva One (untested)
RedHat Linux 7.2 (RH7)
RedHat Linux 7.3 (RH7)
RedHat Linux 8.0 (RH8) TBD
RedHat Linux 9 (RH9) TBD
RedHat Enterprise Linux 3.0 (EL3) TBD
RedHat Enterprise Linux 4 (EL4)
RedHat Enterprise Linux 5 (EL5)
SuSE 8.0 Professional (SuSE8.0) TBD
SuSE 9.1 Personal (SuSE9.1) TBD
SuSE 9.2 Professional (SuSE9.2) TBD
SuSE OpenSuSE (SuSEOSS) TBD
SuSE 10.0 (SuSE10.0) TBD
SuSE 10.1 (SuSE10.1) TBD
SuSE 10.2 (SuSE10.2) TBD
SuSE 10.3 (SuSE10.3) TBD
SuSE 11.0 (SuSE11.0)
SLES 9 (SLES9) TBD
SLES 9 SP2 (SLES9) TBD
SLES 9 SP3 (SLES9) TBD
SLES 10 (SLES10)
Ubuntu 5.10 (ubu5.10) TBD
Ubuntu 6.03 LTS (ubu6.03) TBD
Ubuntu 6.10 (ubu6.10) TBD
Ubuntu 7.04 (ubu7.04) TBD
Ubuntu 7.10 (ubu7.10)
Ubuntu 8.04 (ubu8.04)
WhiteBox Enterprise Linux 3.0 (WBEL3) TBD
WhiteBox Enterprise Linux 4 (WBEL4) TBD

When installing from the tarball (see Installing the Tar Ball), this distribution is probably compatible with a much broader array of distributions than those listed above. These are the distributions against which the current maintainer creates and tests builds.

5.2.2 Architectures

The OpenSS7 IPERF Utility package compiles and installs on a wide range of architectures. Although it is believed that the package will work on all architectures supported by the Linux kernel being used, validation testing has only been performed with the following architectures:

ix86
x86_64
ppc (MPC 860)
ppc64

32-bit compatibility validation testing is performed on all 64-bit architectures supporting 32-bit compatibility. If you would like to validate an OpenSS7 package on a specific machine architecture, you are welcome to sponsor the project with a test machine.

5.2.3 UI Iperf

This section addresses compatibility issues between OpenSS7 and University of Illinois DAST releases of iperf.

iperf-2.0.8 and Iperf Compatibility

OpenSS7 modifications to support SCTP does not alter the data structures nor fundamental operation. New structures and test definitions have been added for SCTP that are largely consistent with those of TCP.

Specifically, an iperf-2.0 client should be able to connect and perform tests with an iperf-2.0.8 server. Also, an iperf-2.0.8 client should be able to connect and perform tests (other than SCTP) with an iperf-2.0 server.

iperf-2.0.8 and Option Compatibility

OpenSS7 releases provide all options compiled-in to the program. This obviates the need for editing makefiles and recompiling the program from source as is described in the University of Illinois DAST documentation. Additional options were provided to support SCTP.

iperf-2.0.8 and SCTP Compatibility

SCTP API tests are (likely) only compatible with the OpenSS7 Sockets implementations of SCTP. The reason for this is that the OpenSS7 Sockets implementations use the POSIX standard socket API rather than the non-standard socket API described in documents such as draft-stewart-tsvwg-sctpsocket-xx.txt.

5.3 Release Notes

The sections that follow provide information on OpenSS7 releases of the OpenSS7 IPERF Utility package as well as compatibility information of OpenSS7 releases to the original University of Illinois releases.

Major changes for release iperf-2.0.8

This is the eighth full release of the OpenSS7 IPERF Utility package. This is a stable, production grade release: it deprecates previous releases. Please upgrade to the most current release before reporting bugs.

This release is largely a maintenance release that provides support for more distributions an architectures as well as tracking feature updates on related packages (i.e. sctp-0.2.27).

Major features since the last public release are as follows:

Minor documentation corrections.
License upgrade to AGPL Version 3.
Support for flex 2.5.33 in maintainer mode.
Ability to strap out major documentation build and installation primarily for embedded targets.
Improvements to common build process for embedded and cross-compile targets.
Updated tool chain to m4-1.4.12, autoconf-2.63 and texinfo-4.13.
Conversion of RPM spec files to common approach for major subpackages.
Updated references database for manual pages and roff documents.
Build system now builds yum(8) repositories for RPMs and apt-get(8) repositories for DEBs. Installation documentation has been updated to include details of repository install sourcesref.
Added MODULE_VERSION to all modules and drivers.

This is a public stable production grade release of the package: it deprecates previous releases. Please upgrade to the current release before reporting bugs.

As with other OpenSS7 releases, this release configures, compiles, installs and builds RPMs and DEBs for a wide range of Linux 2.4 and 2.6 RPM- and DPKG-based distributions, and can be used on production kernels without patching or recompiling the kernel.

This package is publicly released under the GNU Affero General Public License Version 3 as well as the University of Illinois license (see LICENSE in the release for more information). The release is available as an autoconf tarball, SRPM, DSC, and set of binary RPMs and DEBs. See the downloads page for the autoconf tarballs, SRPMs and DSCs. For tarballs, SRPMs, DSCs and binary RPMs and DEBs, see the iperf package page.

See http://www.openss7.org/codefiles/iperf-2.0.8/ChangeLog and http://www.openss7.org/codefiles/iperf-2.0.8/NEWS in the release for more information. Also, see the iperf.pdf manual in the release (also in html http://www.openss7.org/iperf_manual.html).

For the news release, see http://www.openss7.org/rel20081029_1.html.

Major changes for release iperf-2.0.7

This is the seventh full release of the OpenSS7 IPERF Utility package. This is a stable, production grade release: it deprecates previous releases. Please upgrade to the most current release before reporting bugs.

This release is largely a maintenance release that provides support for more distributions an architectures as well as tracking feature updates on related packages (i.e. sctp-0.2.27).

Major features since the last public release are as follows:

Support build on openSUSE 10.2.
Support build on Fedora 7 with 2.6.21 kernel.
Support build on CentOS 5.0 (RHEL5).
Support build on Ubuntu 7.04.
Updated to gettext 0.16.1.
Supports build on Fedora Core 6.
Support for recent distributions and tool chains.

Major changes for release iperf-2.0.6

This is the sixth full release of the OpenSS7 IPERF Utility package. This is a stable, production grade release: it deprecates previous releases. Please upgrade to the most current release before reporting bugs.

This release is largely a maintenance release that provides support for more distributions an architectures as well as tracking feature updates on related packages (i.e. sctp-0.2.27).

Major features since the last public release are as follows:

Support for autoconf 2.61, automake 1.10 and gettext 0.16.
Support for Ubuntu 6.10 distribution and bug fixes for i386 kernels.
The package now looks for other subpackages with a version number as unpacked by separate tarball.

Major changes for release iperf-2.0.5

This is the fifth full release of the OpenSS7 IPERF Utility package. This is a stable, production grade release: it deprecates previous releases. Please upgrade to the most current release before reporting bugs.

This release is largely a maintenance release that provides support for more distributions an architectures as well as tracking feature updates on related packages (i.e. sctp-0.2.27).

Additional features include:

Added send-pr scripts for automatic problem report generation.
Added --disable-devel configure option to suppress building and installing development environment. This feature is for embedded or pure run-time targets that do not need the development environment (static libraries, manual pages, documentation).
Improved compiler flag generation and optimizations for recent gcc compilers and some idiosyncratic behaviour for some distributions (primarily SUSE).
Optimized compilation is now available also for user level programs in addition to kernel programs. Added new --with-optimize option to configure to accomplish this.
Better detection of SUSE distributions, release numbers and SLES distributions: support for additional SuSE distributions on ix86 as well as x86_64. Added distribution support includes SLES 9, SLES 9 SP2, SLES 9 SP3, SLES 10, SuSE 10.1.
Many documentation updates for all OpenSS7 packages. Automated release file generation making for vastly improved and timely text documentation present in the release directory.

Major changes for release iperf-2.0.5.rc3

Third release candidate. This is a maintenance release candidate. This release candidate includes:

Automated release file generation making for vastly improved and timely text documentation present in the release directory.
Many documentation updates for all OpenSS7 packages.
Changes made to the strsctp drivers at the 2006 SCTP Interop at the University of British Columbia. This version was interoperability tested with all implementations present.
Support for additional SuSE distributions on ix86 as well as x86_64. Added distribution support includes SLES 9, SLES 9 SP2, SLES 9 SP3, SLES 10, SuSE 10.1.
Better detection of SUSE distributions, release numbers and SLES distributions.
Optimized compilation for user level programs. New --with-optimize option to configure.
Now includes an Installation and Reference Manual (you are reading it).

This was an internal alpha test release candidate and was not released publicly. This release was only available to subscribers to and sponsors of the OpenSS7 Project.

Major changes for release iperf-2.0.5.rc2

Second release candidate. This is a maintenance release candidate. This release candidate includes:

Results of performance testing of the new second generation UDP driver (implemented completely in STREAMS instead of using an internal socket).
Support for SuSE 10.1.

This was an internal alpha test release candidate and was not released publicly. This release was only available to subscribers to and sponsors of the OpenSS7 Project.

Major changes for release iperf-2.0.5rc1

Release candidate for Mark Fugate. This is a maintenance release candidate. This release candidate includes:

Added --enable-devel configure option for embedded targets.
Added send-pr script for automatic problem report generation.

This was an internal alpha test release candidate and was not released publicly. This release was only available to subscribers to and sponsors of the OpenSS7 Project.

Major changes for release iperf-2.0.4

Corrections for and testing of 64-bit clean compile and test runs on x86_64 architecture. Some bug corrections resulting from gcc 4.0.2 compiler warnings.

Major changes for release iperf-2.0.3

Minor changes and bug fixes. Still remaining to do is merge in the latest upstream release of iperf.

Initial public release iperf-2.0.2

With this release version numbers were changed to reflect an upstream version only to be consistent with other OpenSS7 package releases. All RPM release numbers will be -1$(PACKAGE_RPMEXTRA) and all Debian release numbers will be _0. If you wish to apply patches and release the package, please bump up the release number and apply a suitable release suffix for your organization. We leave Debian release number _1 reserved for your use, so you can still bundle the source in the .dsc file.

Initial release iperf-2.0.1-1

Initial autoconf/rpm packaging release of Iperf.

This is an autoconf/rpm release of Iperf suitable for use with OpenSS7 Linux Native SCTP (Stream Control Transmission Protocol). It is usable for performance testing the SCTP application as well as supporting all other Iperf TCP and UDP testing.

Not publicly released.

5.4 Maturity

The OpenSS7 Project adheres to the following release philosophy:

pre-alpha release
alpha release
beta release
gamma release
production release
unstable release

5.4.1 Pre-Alpha Releases

Pre-alpha releases are releases that have received no testing whatsoever. Code in the release is not even known to configure or compile. The purpose of a pre-alpha release is to make code and documentation available for inspection only, and to solicit comments on the design approach or other characteristics of the software package.

Pre-alpha release packages ship containing warnings recommending that the user not even execute the contained code.

5.4.2 Alpha Releases

Alpha releases are releases that have received little to no testing, or that have been tested and contains known bugs or defects that make the package unsuitable even for testing. The purpose for an alpha release are the same as for the pre-alpha release, with the additional purpose that it is an early release of partially functional code that has problems that an external developer might be willing to fix themselves and contribute back to the project.

Alpha release packages ship containing warnings that executing the code can crash machines and might possibly do damage to systems upon which it is executed.

5.4.3 Beta Releases

Beta releases are releases that have received some testing, but the testing to date is not exhaustive. Beta release packages do not ship with known defects. All known defects are resolved before distribution; however, as exhaustive testing has not been performed, unknown defects may exist. The purpose for a beta release is to provide a baseline for other organizations to participate in the rigorous testing of the package.

Beta release packages ship containing warnings that the package has not been exhaustively tested and that the package may cause systems to crash. Suitability of software in this category for production use is not advised by the project; however, as always, is at the discretion of the user of the software.

5.4.4 Gamma Releases

Gamma releases are releases that have received exhaustive testing within the project, but external testing has been minimal. Gamma release packages do not ship with known defects. As exhaustive internal testing has been performed, unknown defects should be few. Please remember that there is NO WARRANTY on public release packages.

Gamma release packages typically resolve problems in previous beta releases, and might not have had full regression testing performed. Suitability of software in this category for production use is at the discretion of the user of the software. The OpenSS7 Project recommends that the complete validation test suites provided with the package be performed and pass on target systems before considering production use.

5.4.5 Production Releases

Production releases are releases that have received exhaustive testing within the project and validated on specific distributions and architectures. Production release packages do not ship with known defects. Please remember that there is NO WARRANTY on public release packages.

Production packages ship containing a list of validated distributions and architectures. Full regression testing of any maintenance changes is performed. Suitability of software in this category for production use on the specified target distributions and architectures is at the discretion of the user. It should not be necessary to preform validation tests on the set of supported target systems before considering production use.

5.4.6 Unstable Releases

Unstable releases are releases that have received extensive testing within the project and validated on a a wide range of distributions and architectures; however, is has tested unstable and found to be suffering from critical problems and issues that cannot be resolved. Maintenance of the package has proved impossible. Unstable release packages ship with known defects (and loud warnings). Suitability of software in this category for production use is at the discretion of the user of the software. The OpenSS7 Project recommends that the problems and issues be closely examined before this software is used even in a non-production environment. Each failing test scenario should be completely avoided by the application. OpenSS7 beta software is more stable that software in this category.

5.5 Bugs

5.5.1 Defect Notices

OpenSS7 IPERF Utility could contain unknown defects. This is a beta release. Some defects could be harmful. Validation testing has been performed by the OpenSS7 Project on this software for only a restricted set of systems. The software might fail to configure or compile on other systems. The OpenSS7 Project recommends that you do not use this software for purposes other than validation testing and evaluation, and then only with care. Use at your own risk. Remember that there is NO WARRANTY.⁹

This software is beta software. As such, it might crash your kernel. Installation of the software might mangle your header files or Linux distribution in such a way as to make it unusable. Crashes could lock your system and rebooting the system might not repair the problem. You can possibly lose all the data on your system. Because this software might crash your kernel, the resulting unstable system could possibly destroy computer hardware or peripherals making them unusable. You might void the warranty on any system on which you run this software. YOU HAVE BEEN WARNED.

5.5.2 Known Defects

With the exception of packages not originally created by the OpenSS7 Project, the OpenSS7 Project software does not ship with known bugs in any release stage except pre-alpha. OpenSS7 IPERF Utility had no known bugs at the time of release.

Nevertheless, the OpenSS7 Project does not validate the OpenSS7 IPERF Utility package, but simply uses it for benchmark performance testing. Following are some of the expected difficulties with the package that have not yet been discovered:

No bug fixes from the original Iperf development stream have been rolled back into this release. Therefore, any bugs reported on the regular Iperf release package probably still exist unfixed in this release package.

5.5.3 Defect History

This section contains historical bugs that were encountered during development and their resolutions. This list serves two purposes:

It captures bugs encountered between releases during development that could possibly reoccur (and the Moon is made of blue cheese). It therefore provides a place for users to look if they encounter a problem.
It provides a low overhead bug list between releases for developers to use as a TODO list.

Bugs

(no items)

5.6 Schedule

Current Plan

There is no current plan for the iperf package beyond minor distribution maintenance. The package tests the OpenSS7 Linux Native Sockets version of sctp (‘sctp’ package) nicely, but that package only runs on 2.4 kernels. When the strsock package is complete for Linux Fast-STREAMS, the OpenSS7 Project will likely haul this back out and use it for testing the STREAMS versions of UDP, TCP and SCTP using the socklib interface. But, the strsock package completion itself is not planned, so you can only likely expect maintenance releases of this package. The package could be extended to test lksctp as well, however, comparisons between lksctp and sctp can only be done on 2.4 kernels for now. This type of work has been mooted by the current popularity of 2.6 kernels.

Things to Do

Write a texinfo manual for Iperf.
*done*
You are reading it.
Merge upstream changes from the latest University of Illinois release of the Iperf package into the OpenSS7 Modified version. It would really like to do this but don't have the time for it right now. If someone is willing to dive in and give this a try, send me the patches.
Iperf is capable of performing performance testing on lksctp as well. I would like to modify the OpenSS7 version of Iperf to support both so that performance comparison testing can be done between lkstcp (which sucks of course) and OpenSS7.

5.7 History

For the latest developments with regard to history of changes, please see the ChangeLog file in the release package.

6 Installation

6.1 Repositories

The OpenSS7 IPERF Utility package release can be accessed from the repositories of The OpenSS7 Project. For rpm(1) based systems, the package is available in a yum(8) repository based on repomd XML and may also be accessed using zypper(8) or yast(8). For dpkg(1) based systems, the package is available in a apt(8) repository.

By far the easiest (most repeatable and manageable) form for installing and using OpenSS7 packages is to install packages from the yum(8) or apt(8) repositories. If your distribution does not support yum(8), zypper(8), yast(8) or apt(8), then it is still possible to install the RPMs or DEBs from the repositories using rpm(1), dpkg(1); or by using wget(1) and then installing them from RPM or DEB using rpm(1) or dpkg(1) locally.

If binaries are not available for your distribution or specific kernel, but your distribution supports rpm(1) or dpkg(1), the next best method for installing and using OpenSS7 packages is to download and rebuild the source RPMs or DSCs from the repository. This can also be performed with yum(8), zypper(8), yast(8), apt(8); or directly using wget(1), rpm(1) or dpkg(1).

If your architecture does not support rpm(1) or dpkg(1) at all, or you have special needs (such as cross-compiling for embedded targets), the final resort method is to download, configure, build and install from tarball. In this later case, the easiest way to build and install OpenSS7 packages from tarball is to use the tarball for the OpenSS7 Master Package, openss7-0.9.2.G.

6.1.1 Repositories for YUM

To install or upgrade from the OpenSS7 repomd repositories, you will need a file in your /etc/yum.repo.d/ directory. This file can be obtained directly from the OpenSS7 repository, like so:

     $> REPOS="http://www.openss7.org/repos/rpms"
     $> wget $REPOS/centos/5.2/x86_64/repodata/openss7.repo
     $> sudo cp -f openss7.repo /etc/yum.repo.d/
     $> sudo yum makecache

This example assumes the the distribution is ‘centos’ and the distribution release is ‘5.2’ and the architecture requires is ‘x86_64’. Another example would be $REPOS/i686/suse/11.0/i686/repodata/openss7.repo, for using yum(8) with SUSE.

Once the repository is set up, OpenSS7 includes a number of virtual package definitions that eas the installation and removal of kernel modules, libraries and utilities. Downloading, configuring, building and installation for a single-kernel distribution is as easy as:

     $> sudo yum install iperf

Removing the package is as easy as:

     $> sudo yum remove iperf

If you have difficulty downloading the openss7.repo file, edit the following information into the file and place it into the /etc/yum.repo.d/openss7.repo file:

     -| [openss7]
     -| enabled = 1
     -| name = OpenSS7 Repository
     -| baseurl = http://www.openss7.org/repos/rpms/centos/5.2/x86_64
     -| gpgcheck = 1
     -| gpgkey = http://www.openss7.org/pubkey.asc

Note that it is also possible to point to these repositories as an additional installation source when installing CentOS, RedHat, Fedora, or others. You will have an additional STREAMS category from which to choose installation packages.

Some additional installation real or virtual package names and the installations they accomplish are as follows:

‘iperf’: This package can be used to install or remove the entire OpenSS7 IPERF Utility package. When installing, kernel modules will be installed automatically for the highest version kernel on your system. When removing, all corresponding kernel modules will also be removed.
‘iperf-devel’: This package can be used to install or remove the development components of the OpenSS7 IPERF Utility package. When installing, ‘iperf’ and appropriate kernel module and kernel module development and debug packages will also be installed. When removing, the development package and all kernel module development and debug packages will also be removed.
‘iperf-2.4.20-28.7’: This package can be used to install or remove the package for a specific kernel version. When installing, the ‘iperf’ package will also be installed if necessary. When removing the last kernel module package, the ‘iperf’ package will also be removed.
Note that the version ‘2.4.20-28.7’ is just an example. Use the version returned by ‘$(uname -r)’ for the kernel for which you wish to install or remove the packages.
‘iperf-2.4.20-28.7-devel’: This package can be used to install or remove the development and debug packages for a specific kernel version. When installing, the ‘iperf’ and ‘iperf-devel’ packages will also be installed if necessary. When removing the development and debug for kernel modules for the last kernel, the ‘iperf-devel’ package will also be removed.
Note that the version ‘2.4.20-28.7’ is just an example. Use the version returned by ‘$(uname -r)’ for the kernel for which you wish to install or remove the packages.

For assistance with specific RPMs, see Downloading the Binary RPM.

6.1.2 Repositories for APT

For assistance with specific DEBs, see Downloading the Debian DEB.

6.2 Downloading

The OpenSS7 IPERF Utility package releases can be downloaded from the downloads page of The OpenSS7 Project. The package is available as a binary RPM (for popular architectures) a source RPM, Debian binary DEB and source DSC, or as a tar ball. If you are using a browsable viewer, you can obtain the OpenSS7 release of Iperf from the links in the sections that follow.

By far the easiest (most repeatable and manageable) form for installing and using OpenSS7 packages is to download and install individual packages from binary RPM or DEB. If binary RPMs or DEBs are not available for your distribution, but your distribution supports rpm(1) or dpkg(1), the next best method for installing and using OpenSS7 packages is to download and rebuild the source RPMs or DSCs.

6.2.1 Downloading with YUM

OpenSS7 repositories support yum(8) and zypper(8) in repomd XML format as well as YaST and YaST2 formats.

OpenSS7 includes virtual packages that ease the installation and removal of kernel modules, libraries and utilities. Downloading, configuration, building and installation for a signle-kernel distribution installation is as easy as:

     % sudo yum install iperf

This and additional packages for installation are detailed as follows:

iperf

Install this package if you need the runtime iperf package.

          % sudo yum install iperf

This will install the iperf, iperf-lib and iperf-KVERSION RPMs, where ‘KVERSION’ is the highest version number kernel on your system.

Remove this package if you need to remove all vestages of the iperf package.

          % sudo yum remove iperf

This will remove the iperf, iperf-lib, iperf-devel, iperf-KVERSION and iperf-devel-KVERSION RPMs for all kernels on your system.

iperf-devel

Install this package if you need the development iperf package.

          % sudo yum install iperf-devel

This will install the iperf, iperf-lib, iperf-devel, iperf-KVERSION and iperf-devel-KVERSION RPMs, where ‘KVERSION’ is the highest version number kernel on your system.

Remove this package if you do not need development capabilities for the iperf package for any kernel.

          % sudo yum remove iperf-devel

This will remove the iperf-devel and iperf-devel-KVERSION RPMs for all kernels on your system.

iperf-2.4.20-28.7

Install this package if you need the runtime iperf for kernel version ‘2.4.20-28.7’. The value ‘2.4.20-28.7’ is just an example. For the running kernel, you can install the runtime iperf components with:

          % sudo yum install iperf-$(uname -r)

This will install the iperf, iperf-lib and iperf-2.4.20-28.7 RPMs, where ‘2.4.20-28.7’ is the kernel version specified.

Remove this package if you no longer need the runtime iperf for kernel version ‘2.4.20-28.7’. The value ‘2.4.20-28.7’ is just an example. For the running kernel, you can remove the runtime iperf components with:

          % sudo yum remove iperf-$(uname -r)

This will remove the iperf-2.4.20-28.7 and iperf-devel-2.4.20-28.7 RPMs, where ‘2.4.20-28.7’ is the kernel version specified. Also, if this is the last kernel for which iperf was installed, the iperf iperf-lib and iperf-devel RPMs will also be removed.

Note that this is a virtual package name: the actual RPMs installed or removed from the system is a kernel module package whose precise name will depend upon the system being used.

iperf-devel-2.4.20-28.7

Install this package if you need the development iperf package for kernel version ‘2.4.20-28.7’. The value ‘2.4.20-28.7’ is just an example. For the running kernel, you can install the kernel development iperf components with:

          % sudo yum install iperf-devel-$(uname -r)

This will install the iperf, iperf-lib, iperf-devel, iperf-2.4.20-28.7 and iperf-devel-2.4.20-28.7 RPMs, where ‘2.4.20-28.7’ is the kernel version specified.

Remove this package if you no longer need the development capabilities for the iperf package for kernel version ‘2.4.20-28.7’. The value ‘2.4.20-28.7’ is just an example. For the running kernel, you can remove the kernel development iperf components with:

          % sudo yum remove iperf-devel-$(uname -r)

This will remove the iperf-devel-2.4.20-28.7 RPMs, where ‘2.4.20-28.7’ is the kernel version specified. Also, if this is the last kernel for which iperf was installed, the iperf-devel RPMs will also be removed.

Note that this is a virtual package name: the actual RPMs installed or removed from the system is a kernel module package whose precise name will depend upon the system being used.

iperf-lib

This package is an auxillary package that should be removed and inserted automatically by yum(8). In rare instances you might need to remove or install this package explicitly.

6.2.2 Downloading with APT

OpenSS7 repositries support apt(8) repositorie digests and signatures.

6.2.3 Downloading the Binary RPM

To install from binary RPM, you will need several of the RPM for a complete installation. Binary RPM fall into several categories. To download and install a complete package requires the appropriate RPM from each of the several categories below, as applicable. Some release packages do not provide RPMs in each of the several categories.

To install from Binary RPM, you will need all of the following independent packages for your architecture.

Independent RPM

Independent RPM are not dependent on either the Linux kernel version, or the STREAMS package. For example, the source package ‘iperf-source-2.0.8-1.7.2.noarch.rpm’, is not dependent on kernel nor STREAMS package.

All of the following independent RPM are required for your architecture. Binary RPMs listed here are for example only: additional binary RPMs are available from the downloads site. If your architecture is not available, you can build binary RPM from the source RPM (see see Building from the Source RPM).

Architecture Independent

iperf-doc-2.0.8-1.7.2.noarch.rpm: The iperf-doc package contains this manual in plain text, postscript, pdf and html forms, along with the meta-information from the Iperf package. It also contains all of the manual pages necessary for developing OpenSS7 IPERF Utility applications and OpenSS7 IPERF Utility STREAMS modules or drivers.
iperf-source-2.0.8-1.7.2.noarch.rpm: The iperf-source package contains the source code necessary for building the OpenSS7 IPERF Utility release. It includes the autoconf(1) configuration utilities necessary to create and distribute tarballs, rpm and deb/dsc. ¹⁰

Architecture Dependent

The following Architecture Dependent packages are required for your architecture. If your architecture is not on the list, you can build binary RPM from the source RPM (see see Building from the Source RPM).

iperf-openss7-2.0.8-1.7.2.i686.rpm: The iperf-openss7 package contains the iperf(1) program compiled to work with the OpenSS7 Linux Native Sockets version of SCTP.
iperf-devel-2.0.8-1.7.2.i686.rpm: The iperf-devel package contains library archives for static compilation, header files to develop OpenSS7 IPERF Utility modules and drivers. This also includes the header files and static libraries required to compile OpenSS7 IPERF Utility applications programs.
iperf-lib-2.0.8-1.7.2.i686.rpm: The iperf-lib package contains the run-time shared libraries necessary to run application programs and utilities developed for the Iperf package. ¹¹

Configuration and Installation

To configure, build and install the binary RPM, See Configuring the Binary RPM.

6.2.4 Downloading the Debian DEB

To install from binary DEB, you will need several of the DEB for a complete installation. Binary DEB fall into several categories. To download and install a complete package requires the appropriate DEB from each of the several categories below, as applicable. Some release packages do not provide DEBs in each of the several categories.

To install from Binary DEB, you will need all of the following independent packages for your architecture.

Independent DEB

Independent DEB are dependent on neither the Linux kernel version, nor the STREAMS package. For example, the source package ‘iperf-source_2.0.8-0_i386.deb’, is not dependent on kernel nor STREAMS package.

All of the following independent DEB are required for your architecture. Binary DEBs listed here are for example only: additional binary DEBs are available from the downloads site. If your architecture is not available, you can build binary DEB from the Debian DSC (see see Building from the Debian DSC).

Architecture Independent

iperf-doc_2.0.8-0_all.deb: The iperf-doc package contains this manual in plain text, postscript, pdf and html forms, along with the meta-information from the Iperf package. It also contains all of the manual pages necessary for developing OpenSS7 IPERF Utility applications and OpenSS7 IPERF Utility STREAMS modules or drivers.
iperf-source_2.0.8-0_all.deb: The iperf-source package contains the source code necessary for building the OpenSS7 IPERF Utility release. It includes the autoconf(1) configuration utilities necessary to create and distribute tarballs, rpms and deb/dscs. ¹²

Architecture Dependent

The following Architecture Dependent packages are required for your architecture. If your architecture is not on the list, you can build binary DEB from the Debian DSC (see see Building from the Debian DSC).

iperf-openss7_2.0.8-0_i386.deb: The iperf-openss7 package contains the iperf(1) program compiled to work with the OpenSS7 Linux Native Sockets version of SCTP.
iperf-devel_2.0.8-0_i386.deb: The iperf-devel package contains library archives for static compilation, header files to develop OpenSS7 IPERF Utility modules and drivers. This also includes the header files and static libraries required to compile OpenSS7 IPERF Utility applications programs.
iperf-lib_2.0.8-0_i386.deb: The iperf-lib package contains the run-time shared libraries necessary to run application programs and utilities developed for the Iperf package. ¹³

Configuration and Installation

To configure, build and install the Debian DEB, See Configuring the Debian DEB.

6.2.5 Downloading the Source RPM

If you cannot obtain a binary RPM for your architecture, or would like to roll you own binary RPM, download the following source RPM.

iperf-2.0.8-1.src.rpm: This is the source RPM for the package. From this source RPM it is possible to build binary RPM for any supported architecture and for any 2.4 kernel.

Configuration

To configure the source RPM, See Configuring the Source RPM.

6.2.6 Downloading the Debian DSC

If you cannot obtain a binary DEB for your architecture, or would like to roll your own DEB, download the following Debian DSC.

iperf_2.0.8-0.dsc
iperf_2.0.8-0.tar.gz: This is the Debian DSC for the package. From this Debian DSC it is possible to build binary DEB for any supported architecture and for any 2.4 kernel.

Configuration

To configure the source RPM, See Configuring the Debian DSC.

6.2.7 Downloading the Tar Ball

For non-rpm(1) and non-dpkg(1) architectures, download the tarball as follows:

iperf-2.0.8.tar.gz
iperf-2.0.8.tar.bz2: These are the tar(1) balls for the release. These tar(1) balls contain the autoconf(1) distribution which includes all the source necessary for building and installing the package. These tarballs will even build Source RPM and Binary RPM on rpm(1) architectures and Debian DSC and DEB on dpkg(1) architectures.

The tar ball may be downloaded easily with wget(1) as follows:

     % wget http://www.openss7.org/iperf-2.0.8.tar.bz2

     % wget http://www.openss7.org/iperf-2.0.8.tar.gz

Note that you will need an OpenSS7 Project user name and password to download release candidates (which are only available to subscribers and sponsors of the OpenSS7 Project).

Unpacking the Archive

After downloading one of the tar balls, unpack the archive using one of the following commands:

     % wget http://www.openss7.org/iperf-2.0.8.tar.gz
     % tar -xzvf iperf-2.0.8.tar.gz

     % wget http://www.openss7.org/iperf-2.0.8.tar.bz2
     % tar -xjvf iperf-2.0.8.tar.bz2

Either will create a subdirectory name iperf-2.0.8 containing all of the files and subdirectories for the Iperf package.

Configuration

To configure and install the tar ball, See Configuring the Tar Ball.

6.2.8 Downloading from CVS

If you are a subscriber or sponsor of The OpenSS7 Project with CVS archive access privileges then you can download release, mid-release or release candidate versions of the Iperf package from the project CVS archive.

The OpenSS7 IPERF Utility package is located in the iperf module of /var/cvs. For release tag information, see Releases.

To access the archive from the project CVS pserver, use the following commands to check out a version from the archive:

     % export CVSROOT='-d:pserver:username@cvs.openss7.com:2401/var/cvs'
     % cvs login
     Password: *********
     % cvs co -r iperf_2.0.8 iperf
     % cvs logout

It is, of course, possible to check out by date or by other criteria. For more information, see cvs(1).

Preparing the CVS Working Directory

Although public releases of the Iperf package do not require reconfiguration, creating a configurable directory from the CVS archive requires tools not normally distributed with the other releases.

The build host requires the following GNU tools:

m4 1.4.12
autoconf 2.63
automake 1.10.1
libtool 2.2.4
gettext 0.17
flex 2.5.33
bison 2.3

Most desktop development GNU/Linux distributions wil have these tools; however, some non-development or server-style installations might not and they must be installed separately.¹⁴

Also, these tools can be acquired from the FSF website in the free software directory, and also at the following locations:

It should be stressed that, in particular, the autoconf(1), and automake(1), must be at version releases 2.63 and 1.10.1. The versions normally distributed in some mainstream GNU/Linux distributions are, in fact, much older than these versions.¹⁵ GNU version of these packages configured and installed to default directories will install in /usr/local/ allowing them to coexist with distribution installed versions.

For building documentation, the build host also requires the following documentation tools:

gs 6.51 or ghostscript 6.51, or newer.
tetex 3.0 or texlive 2007, or newer.
texinfo 4.13a or newer.
transfig 3.2.3d or newer.
imagemagick 5.3.8 or ImageMagick 5.3.8, or newer.
groff 1.17.2 or newer.
gnuplot 3.7 or newer.
latex2html 1.62 or newer.

Most desktop GNU/Linux distributions will have these tools; however, some server-style installations (e.g. Ubuntu-server, SLES 9 or Fedora 6 or 7) will not and they must be installed separately.¹⁶

Note that texinfo 4.12 must not be used as it breaks the build process.

For uncooked manual pages, the entire groff(1) package is required on Debian and Ubuntu systems (the base package does not include grefer(1) which is used extensively by uncooked manual pages). The following will get what you need:

     Debian: % apt-get install groff_ext
     Ubuntu: % apt-get install groff

In addition, the build host requires a complete tool chain for compiling for the target host.

If you wish to package rpms on an rpm(1) system, or debs on a dpkg(1) system, you will need the appropriate tool chain. Systems based on rpm(1) typically have the necessary tool chain available, however, dpkg(1) systems do not. The following on a Debian or Ubuntu system will get what you need:

     % apt-get install debhelper
     % apt-get install fakeroot

To generate a configuration script and the necessary scriptlets required by the GNU autoconf(1) system, execute the following commands on the working directory:

     % autoreconf -fiv iperf

where, iperf is the name of the directory to where the working copy was checked out under the previous step. This command generates the configure script and other missing pieces that are normally distributed with the release Tar Balls, SRPMs and DSCs.

Make sure that ‘autoreconf --version’ returns ‘2.63’. Otherwise, you may need to perform something like the following:

     % PATH="/usr/local/bin:$PATH"
     % autoreconf -fiv iperf

After reconfiguring the directory, the package can then be configured and built using the same instructions as are used for the Tar Ball, see Configuring the Tar Ball, and Building from the Tar Ball.

Do note, however, that make(1) will rebuild the documentation that is normally released with the package. Additional tools may be necessary for building the documentation. To avoid building and installing the documentation, use the --disable-devel or --disable-docs option to configure described in Configuring the Tar Ball.

When configuring the package in a working directory and while working a change-compile-test cycle that involves configuration macros or documentation, I find it of great advantage to invoke the GNU configure options --enable-maintainer-mode, --enable-dependency-tracking and --disable-devel. The first of these three options will add maintainer-specific targets to any generated Makefile, the second option will invoke automatic dependency tracking within the Makefile so rebuilds after changes to macro, source or documentation files will be automatically rebuilt; and the last option will suppress rebuilding and reinstalling documentation manual pages and header files. Header files will still be available under the /usr/src directory.

6.3 Configuration

6.3.1 Configuring the Binary RPM

In general the binary RPM do not require any configuration, however, during installation it is possible to relocate some of the installation directories. This allows some degree of customization. Relocations that are available on the binary RPM are as follows:

iperf-devel-2.0.8-1.7.2.i686.rpm

/usr/lib: This relocatable directory contains iperf libraries.
/usr/include/iperf: This relocatable directory contains iperf header files.

iperf-doc-2.0.8-1.7.2.i686.rpm

/usr/share/doc: This relocatable directory contains all package specific documentation (including this manual). The subdirectory in this directory is the iperf-2.0.8 directory.
/usr/share/info: This relocatable directory contains info files (including the info version of this manual).
/usr/share/man: This relocatable directory contains manual pages.

iperf-lib-2.0.8-1.7.2.i686.rpm

/usr/lib: This relocatable directory contains the run-time shared libraries necessary to run applications programs and utilities developed for OpenSS7 IPERF Utility.
/usr/share/locale: This relocatable directory contains the locale information for shared library files.

iperf-source-2.0.8-1.7.2.i686.rpm

/usr/src: This relocatable directory contains the source code.

iperf-openss7-2.0.8-1.7.2.i686.rpm

/usr/bin: This relocatable directory contains binary programs and utilities.

Installation

To install the binary RPM, See Installing the Binary RPM.

6.3.2 Configuring the Debian DEB

In general the binary DEB do not require any configuration.

Installation

To install the Debian DEB, See Installing the Debian DEB.

6.3.3 Configuring the Source RPM

When building from the source RPM (see Building from the Source RPM), the rebuild process uses a number of macros from the user's .rpmmacros file as described in rpm(8).

Following is an example of the ~/.rpmmacros file that I use for rebuilding RPMS:

     #
     # RPM macros for building rpms
     #
     
     %vendor OpenSS7 Corporation
     %distribution OpenSS7
     %disturl http://www.openss7.org/
     %packager Brian Bidulock <[email protected]>
     %url http://www.openss7.org/
     
     %_signature gpg
     %_gpg_path /home/brian/.gnupg
     %_gpg_name [email protected]
     %_gpgbin /usr/bin/gpg
     
     %_source_payload w9.bzdio
     %_binary_payload w9.bzdio
     
     %_unpackaged_files_terminate_build 1
     %_missing_doc_files_terminate_build 1
     %_use_internal_dependency_generator 0
     %_repackage_all_erasures 0
     %_rollback_transaction_on_failure 0
     
     %configure2_5x %configure
     %make make

When building from the source RPM (see Building from the Source RPM), it is possible to pass a number of additional configuration options to the rpmbuild(1) process.

The additional configuration options are described below.

Note that distributions that use older versions of rpm do not have the --with or --without options defined. To achieve the same effect as:

     --with someparm=somearg

do:

     --define "_with_someparm --with-someparm=somearg"

This is a generic description of common rpmbuild(1) options. Not all rpmbuild(1) options are applicable to all SRPMs.

--with checks
--without checks: Enable or disable preinstall checks. Each packages supports a number of preinstall checks that can be performed by invoking the ‘check’ target with automake(1). These currently consist of checking each kernel module for unresolved kernel symbols, checking for documentation for exported kernel module symbols, checking for documentation for exported library symbols, checking for standard options for build and installable programs, checking for documentation for built and installable programs. Normally these checks are only run in maintainer mode, but can be enabled and disabled with this option.
--with cooked-manpages
--without cooked-manpages: Some systems do not like grefer(1) references in manual pages.¹⁷ This option will cook soelim(1), refer(1), tbl(1) and pic(1) commands from the manual pages and also strip groff(1) comments. The default is to leave manual pages uncooked: they are actually smaller that way.
--with public
--without public: Release public packages or private packages. This option has no effect on the Iperf package. The default is to release public packages.
--with devel
--without devel: Specifies whether to build development environment packages such as those that include header files, static libraries, manual pages and texinfo(1) documentation. The default is to build development environment packages. This option can be useful when building for an embedded target where only the runtime components are desired.
--with docs
--without docs: Specifies whether to build and install major documentation such manual pages and texinfo(1) documentation. The default is to build and install documentation. This option can be useful when building for an embedded target where only the runtime and static compile components are desired, but not major documentation. This option does not override the setting of --without devel.

In addition, the following rpm options, specific to the OpenSS7 IPERF Utility package are available:

--without ipv6
--with ipv6: Disable ipv6 support. This option defaults to auto detection.
--without multicast
--with multicast: Disable multicast support. This option defaults to auto detection.
--without threads
--with threads: Disable thread support. This option defaults to auto detection.
--without web100
--with web100: Disable web100 support. This option defaults to auto detection.

In general, the default values of these options are sufficient for most purposes and no options need be provided when rebuilding the Source RPMs.

Build

To build from the source RPM, See Building from the Source RPM.

6.3.4 Configuring the Debian DSC

The Debian DSC can be configured by passing options in the environment variable BUILD_DEBOPTIONS. The options placed in this variable take the same form as those passed to the configure script, See Configuring the Tar Ball. For an example, See Building from the Debian DSC.

Build

To build from the Debian DSC, See Building from the Debian DSC.

6.3.5 Configuring the Tar Ball

All of the normal GNU autoconf(1) configuration options and environment variables apply. Additional options and environment variables are provided to tailor or customize the build and are described below.

6.3.5.1 Configure Options

This is a generic description of common configure options that are in addition to those provided by autoconf(1), automake(1), libtool(1) and gettext(1).

Not all configure options are applicable to all release packages.

Following are the additional configure options, their meaning and use:

--enable-checks
--disable-checks: Enable or disable preinstall checks. Each release package supports a number of preinstall checks that can be performed by invoking the ‘check’ target with make(1). These currently consist of checking each kernel module for unresolved kernel symbols, checking for documentation for exported kernel module symbols, checking for documentation for exported library symbols, checking for standard options for build and installable programs, checking for documentation for built and installable programs. Normally these checks are only run in maintainer mode, but can be enabled and disabled with this option.
--disable-compress-manpages: Compress manual pages with ‘gzip -9’ or ‘bzip2 -9’ or leave them uncompressed. The default is to compress manual pages with ‘gzip -9’ or ‘bzip2 -9’ if a single compressed manual page exists in the target installation directory (--mandir). This disables automatic compression.
--disable-public: Disable public release. This option is not usable on public releases and only has a usable effect on OpenSS7 IPERF Utility when the package is acquired from CVS. In particular, the STREAMS SS7/VoIP/ISDN/SIGTRAN Stacks (strss7-0.9a.8) release package has a large number of non-public components. Specifying this option will cause the package to build and install all private release components in addition to the public release components. This option affects all release packages. Most release packages do not have private release components.
--disable-devel: Disables the installation of development environment components such as header files, static libraries, manual pages and texinfo(1) documentation. The default is to install development environment components. This option can be useful when configuring for an embedded target where only the runtime components are desired, or when performing a edit-compile-test cycle.
--disable-docs: Disables the build and installation of major documentation such manual pages and texinfo(1) documentation. The default is to build and install documentation. This option can be useful when building for an embedded target where only the runtime and static compile components are desired, but not major documentation. This option does not override the setting of --disable-devel.
--enable-arch: Specifies whether architectural dependent package components are to be built and installed. This option can be useful when rebuilding for multiple architectures and target kernels, particularly under dpkg(1). The default is to configure, build and install architecture dependent package components. This option has no effect for release packages that do not provide architecture dependent components.
--enable-indep: Specifies whether architecture independent package components are to be built and installed. This option can be useful when rebuilding for multiple architectures and target kernels, particularly under dpkg(1). The default is to configure, build and install architecture independent package components. This options has no effect for release packages that do not provide architecture independent components.
--with-gpg-user=GNUPGUSER: Specify the gpg(1) ‘GNUPGUSER’ for signing RPMs and tarballs. The default is the content of the environment variable GNUPGUSER. If unspecified, the gpg(1) program will normally use the user name of the account invoking the gpg(1) program. For building source RPMs, the RPM macro ‘_gpg_name’ will override this setting.
--with-gpg-home=GNUPGHOME: Specify the ‘GNUPGHOME’ directory for signing RPMs and tarballs. The default is the user's ~/.gpg directory. For building source RPMs, the RPM macro ‘_gpg_path’ will override this setting.
--with-pkg-epoch=EPOCH: Specifies the epoch for the package. This is neither used for rpm(1) nor dpkg(1) packages, it applies to the tarball release as a whole. The default is the contents of the .pkgepoch file in the release package source directory or, if that file does not exist, zero (0).
--with-pkg-release=RELEASE: Specifies the release for the package. This is neither used for rpm(1) nor dpkg(1) packages, it applies to the tarball release as a whole. The default is the contents of the .pkgrelease file in the release package source directory or, if that file does not exist, one (1). This is the number after the last point in the package version number.
--with-pkg-distdir=DIR: Specifies the distribution directory for the package. This is used by the maintainer for building distributions of tarballs. This is the directory into which archives are copied for distribution. The default is the top build directory.
--with-cooked-manpages: Convert manual pages to remove macro dependencies and grefer(1) references. Some systems do not like grefer(1) references in manual pages.¹⁸ This option will cook soelim(1), refer(1), tbl(1) and pic(1) commands from the manual pages and also strip groff(1) comments. The default is to leave manual pages uncooked (they are actually smaller that way).
--with-rpm-epoch=PACKAGE_EPOCH: Specify the ‘PACKAGE_EPOCH’ for the RPM spec file. The default is to use the RPM epoch contained in the release package file .rpmepoch.
--with-rpm-release=PACKAGE_RPMRELEASE: Specify the ‘PACKAGE_RPMRELEASE’ for the RPM spec file. The default is to use the RPM release contained in the release package file .rpmrelease.
--with-rpm-extra=PACKAGE_RPMEXTRA: Specify the ‘PACKAGE_RPMEXTRA’ extra release information for the RPM spec file. The default is to use the RPM extra release information contained in the release package file .rpmextra. Otherwise, this value will be determined from automatic detection of the RPM distribution.
--with-rpm-topdir=PACKAGE_RPMTOPDIR: Specify the ‘PACKAGE_RPMTOPDIR’ top directory for RPMs. If specified with a null ‘PACKAGE_RPMTOPDIR’, the default directory for the RPM distribution will be used. If this option is not provided on the command line, the top build directory will be used as the RPM top directory as well.
--with-deb-epoch=EPOCH: Specify the ‘PACKAGE_DEBEPOCH’ for the DEB control file. The default is to use the DEB epoch contained in the release package file .debepoch.
--with-deb-release=RELEASE: Specify the ‘PACKAGE_DEBRELEASE’ for the DEB control file. The default is to use the DEB release contained in the release package file .debrelease.
--with-deb-topdir=DIR: Specify the ‘PACKAGE_DEBTOPDIR’ top directory for DEBs. If specified with a null ‘PACKAGE_DEBTOPDIR’, the default directory for the DEB distribution will be used. If this option is not provided on the command line, the top build directory will be used as the DEB top directory as well.

In addition, the following configure options, specific to the OpenSS7 IPERF Utility package are available:

--disable-ipv6: Disable ipv6 support. This option defaults to auto detection.
--disable-multicast: Disable multicast support. This option defaults to auto detection.
--disable-threads: Disable thread support. This option defaults to auto detection.
--disable-web100: Disable web100 support. This option defaults to auto detection.

6.3.5.2 Environment Variables

Following are additional environment variables to configure, their meaning and use:

GPG: GPG signature command. This is used for signing distributions by the maintainer. By default, configure will search for this tool.
GNUPGUSER: GPG user name. This is used for signing distributions by the maintainer.
GNUPGHOME: GPG home directory. This is used for signing distributions by the maintainer.
GPGPASSWD: GPG password for signing. This is used for signing distributions by the maintainer. This environment variable is not maintained by the configure script and should only be used on an isolated system.
SOELIM: Roff source elimination command, soelim(1). This is only necessary when the option --with-cooked-manpages has been specified and configure cannot find the proper soelim(1) command. By default, configure will search for this tool.
REFER: Roff references command, refer(1). This is only necessary when the option --with-cooked-manpages has been specified and configure cannot find the proper refer(1) command. By default, configure will search for this tool.
TBL: Roff table command, tbl(1). This is only necessary when the option --with-cooked-manpages has been specified and configure cannot find the proper tbl(1) command. By default, configure will search for this tool.
PIC: Roff picture command, pic(1). This is only necessary when the option --with-cooked-manpages has been specified and configure cannot find the proper pic(1) command. By default, configure will search for this tool.
GZIP: Default compression options provided to GZIP_CMD.
GZIP_CMD: Manpages (and kernel modules) compression commands, gzip(1). This is only necessary when the option --without-compressed-manpages has not been specified and configure cannot find the proper gzip(1) command. By default, configure will search for this tool.
BZIP2: Default compression options provided to BZIP2_CMD
BZIP2_CMD: Manpages compression commands, bzip2(1). This is only necessary when the option --without-compressed-manpages has not been specified and configure cannot find the proper bzip2(1) command. By default, configure will search for this tool.
MAKEWHATIS: Manpages apropros database rebuild command, makewhatis(8). By default, configure will search for this tool. By default, configure will search for this tool.
RPM: Rpm command, rpm(1). This is only necessary for RPM builds. By default, configure will search for this tool.
RPMBUILD: Build RPM command, rpmbuild(1). This is only necessary for RPM builds. By default, configure will search for this tool. rpm(1) will be used instead of rpmbuild(1) only if rpmbuild(1) cannot be found.
DPKG: Dpkg comand, dpkg(1). This command is used for building Debian packages. By default, configure will search for this tool.
DPKG_SOURCE: Dpkg-source command, dpkg-source(1). This command is used for building Debian dsc packages. By default, configure will search for this tool.
DPKG_BUILDPACKAGE: Dpkg-buildpackage command, dpkg-buildpackage(1). This command is used for building Debian deb packages. By default, configure will search for this tool.
DEB_BUILD_ARCH: Debian build architecture. This variable is used for building Debian packages. The default is the autoconf build architecture.
DEB_BUILD_GNU_CPU: Debian build cpu. This variable is used for building Debian packages. The default is the autoconf build cpu.
DEB_BUILD_GNU_SYSTEM: Debian build os. This variable is used for building Debian packages. The default is the autoconf build os.
DEB_BUILD_GNU_TYPE: Debian build alias. This variable is used for building Debian packages. The default is the autoconf build alias.
DEB_HOST_ARCH: Debian host architecture. This variable is used for building Debian packages. The default is the autoconf host architecture.
DEB_HOST_GNU_CPU: Debian host cpu. This variable is used for building Debian packages. The default is the autoconf host cpu.
DEB_HOST_GNU_SYSTEM: Debian host os. This variable is used for building Debian packages. The default is the autoconf host os.
DEB_HOST_GNU_TYPE: Debian host alias. This variable is used for building Debian packages. The default is the autoconf host alias.
LDCONFIG: Configure loader command, ldconfig(8). Command used to configure the loader when libraries are installed. By default, configure will search for this tool.
DESTDIR: Cross build root directory. Specifies the root directory for build and installation.
OBJDUMP: Object dumping command, objdump(1). This is used for listing information about object files. By default, configure will search for this tool.
NM: Object symbol listing command, nm(1). This is used for listing information about object files. By default, configure will search for this tool.

6.3.5.3 Build

To build from the tar ball, See Building from the Tar Ball.

6.4 Building

6.4.1 Building from the Source RPM

If you have downloaded the necessary source RPM (see Downloading the Source RPM), then the following instructions will rebuild the binary RPMs on your system. Once the binary RPMs are rebuilt, you may install them as described above (see Installing the Binary RPM).

The source RPM is rebuilt to binary RPMs as follows:

     % wget http://www.openss7.org/rpms/SRPMS/iperf-2.0.8-1.src.rpm
     % rpmbuild --rebuild -vv iperf-2.0.8-1.src.rpm

The rebuild process can also recognize a number of options that can be used to tweak the resulting binaries, See Configuring the Source RPM. These options are provided on the rpm(1) command line. For example:

     % rpmbuild --rebuild -vv --target athlon-redhat-linux \
       --with lis -- iperf-2.0.8-1.src.rpm

will rebuild binary RPM for the ‘athlon’ architecture against the LiS STREAMS package.

Installation

To install the resulting binary RPM, See Installing the Binary RPM.

6.4.2 Building from the Debian DSC

If you have downloaded the necessary Debian DSC (see Downloading the Debian DSC), then the following instructions will rebuild the binary DEBs on your system. Once the binary DEBs are rebuilt, you may install them as described above (see Installing the Debian DEB).

The Debian DSC is rebuilt to binary DEBs as follows:

     % wget http://www.openss7.org/debian/iperf_2.0.8-0.dsc
     % wget http://www.openss7.org/debian/iperf_2.0.8-0.tar.gz
     % dpkg-buildpackage -v iperf_2.0.8-0.dsc

The rebuild process can also recognize a number of options that can be used to tweak the resulting binaries, See Configuring the Debian DSC. These options are provided in the environment variable BUILD_DPKGOPTIONS and have the same form as the options to configure, See Configuring the Tar Ball. For example:

     % BUILD_DEBOPTIONS='
             --with-lis
             --host=athlon-debian-linux-gnu'
       dpkg-buildpackage -v \
       iperf_2.0.8-0.dsc

will rebuild binary DEB for the ‘athlon’ architecture against the LiS STREAMS package.

Installation

To install the resulting binary DEB, See Installing the Debian DEB.

6.4.3 Building from the Tar Ball

If you have downloaded the tar ball (see Downloading the Tar Ball), then the following instructions will rebuild the package on your system. (Note that the build process does not required root privilege.)

6.4.3.1 Native Build

Following is an example of a native build against the running kernel:

     % wget http://www.openss7.org/iperf-2.0.8.tar.bz2
     % tar -xjvf iperf-2.0.8.tar.bz2
     % pushd iperf-2.0.8
     % ./configure
     % make
     % popd

6.4.3.2 Cross-Build

Following is an example for a cross-build. The kernel release version must always be specified for a cross-build.¹⁹ If you are cross-building, specify the root for the build with environment variable DESTDIR. The cross-compile host must also be specified if different from the build host. Either the compiler and other tools must be in the usual places where GNU autoconf(1) can find them, or they must be specified with declarations such as ‘CC=/usr/lib/ppc-linux/gcc’ on the configure command line.

     % wget http://www.openss7.org/iperf-2.0.8.tar.bz2
     % tar -xjvf iperf-2.0.8.tar.bz2
     % pushd iperf-2.0.8
     % ./configure DESTDIR="/some/other/root" \
     	--with-k-release=2.4.18 --host sparc-linux
     % make
     % popd

6.5 Installing

6.5.1 Installing the Binary RPM

If you have downloaded the necessary binary RPMs (see Downloading the Binary RPM), or have rebuilt binary RPMs using the source RPM (see Building from the Source RPM), then the following instructions will install the RPMs on your system. For additional information on rpm(1), see rpm(8).

     % pushd RPMS/i686
     % rpm -ihv iperf-*-2.0.8-1.7.2.i686.rpm

You must have the correct binary RPMs downloaded or built for this to be successful.

Some of the packages are relocatable and can have final installation directories altered with the --relocate option to rpm(1), see rpm(8). For example, the following will relocate the documentation and info directories:

     % pushd RPMS/i686
     % rpm -ihv \
             --relocate '/usr/share/doc=/usr/local/share/doc' \
             --relocate '/usr/share/info=/usr/local/share/info' \
             -- iperf-doc-2.0.8-1.7.2.i686.rpm

The previous example will install the iperf-doc package by will relocate the documentation an info directory contents to the /usr/local version.

6.5.2 Installing the Debian DEB

If you have downloaded the necessary Debian DEBs (see Downloading the Debian DEB), or have rebuild binary DEBs using the Debian DSC (see Building from the Debian DSC), then the following instructions will install the DEBs on your system. For additional information see dpkg(8).

     % pushd debian
     % dpkg -iv iperf-*_2.0.8-0_*.deb

You must have the correct .deb files downloaded or build for this to be successful.

6.5.3 Installing the Tar Ball

After the build process (see Building from the Tar Ball), installation only requires execution of one of two automake(1) targets:

‘make install’: The ‘install’ automake(1) target will install all the components of the package. Root privilege is required to successfully invoke this target.
‘make install-strip’: The ‘install-strip’ automake(1) target will install all the components of the package, but will strip unnecessary information out of the objects and compress manual pages. Root privilege is required to successfully invoke this target.

6.6 Removing

6.6.1 Removing the Binary RPM

To remove an installed version of the binary RPMs (whether obtained from the OpenSS7 binary RPM releases, or whether created by the source RPM), execute the following command:

     % rpm -evv `rpm -qa | grep '^iperf-'`

For more information see rpm(1).

6.6.2 Removing the Debian DEB

To remove and installed version of the Debian DEB (whether obtained from the OpenSS7 binary DEB releases, or whether created by the Debian DSC), execute the following command:

     % dpkg -ev `dpkg -l | grep '^iperf-'`

For more information see dpkg(8).

6.6.3 Removing the Source RPM

To remove all the installed binary RPM build from the source RPM, see Removing the Binary RPM. Then simply remove the binary RPM package files and source RPM file. A command such as:

     % find / -name 'iperf-*.rpm' -type f -print0 | xargs --null rm -f

should remove all Iperf RPMs from your system.

6.6.4 Removing the Debian DSC

To remove all the installed binary DEB build from the Debian DSC, see Removing the Debian DEB. Then simply remove the binary DEB package files and Debian DSC file. A command such as:

     % find / \( -name 'iperf-*.deb' \
              -o -name 'iperf-*.dsc' \
              -o -name 'iperf-*.tar.* \
              \) -type f -print0 | xargs --null rm -f

should remove all Iperf DEBs, DSCs and TARs from your system.

6.6.5 Removing the Tar Ball

To remove a version installed from tar ball, change to the build directory where the package was built and use the ‘uninstall’ automake(1) target as follows:

     % cd /usr/src/iperf
     % make uninstall
     % cd ..
     % rm -fr iperf-2.0.8
     % rm -f iperf-2.0.8.tar.gz
     % rm -f iperf-2.0.8.tar.bz2

If you have inadvertently removed the build directory and, therefore, no longer have a configured directory from which to execute ‘make uninstall’, then perform all of the steps for configuration and installation (see Installing the Tar Ball) except the final installation and then perform the steps above.

6.6.5.1 Linux STREAMS Module Loading

LiS is deprecated and this section has been deleted.

6.7 Maintenance

6.7.1 Makefile Targets

automake(1) has many targets, not all of which are obvious to the casual user. In addition, OpenSS7 automake(1) files have additional rules added to make maintaining and releasing a package somewhat easier. This list of targets provides some help with what targets can be invoked, what they do, and what they hope to achieve. The available targets are as follows:

6.7.1.1 User Targets

The following are normal targets intended to be invoked by installers of the package. They are concerned with compiling, checking the compile, installing, checking the installation, and removing the package.

‘[all]’

This is also the default target. It compiles the package and all release packages selected by configure. This is performed after configuring the source with ‘configure’. A Makefile stub is provided so that if the package has not had autoreconf(1) run (such as when checked out from CVS, the package will attempt to run ‘autoreconf -fiv’.

All OpenSS7 Project packages are configured without maintainer mode and without dependency tracking by default. This speeds compilation of the package for one-time builds. This also means that if you are developing using the source package (edit-compile-test cycle), changes made to source files will not cause the automatic rebuilding due to dependencies. There are two ways to enable dependency tracking: specify --enable-maintainer-mode to configure; or, specify --enable-dependency-tracking to configure. I use the former during my edit-compile-test cycle.

This is a standard GNU automake(1) makefile target. This target does not require root privilege.

‘check’

All OpenSS7 Project release packages provide check scripts for the check target. This step is performed after compiling the package and will run all of the ‘check’ programs against the compiled binaries. Which checks are performed depends on whether --enable-maintainer-mode was specified to configure. If in maintainer mode, checks that assist with the release of the package will be run (such as checking that all manual pages load properly and that they have required sections.) We recommend running the check stage before installing, because it catches problems that might keep the installed package from functioning properly.

Another way to enable the greater set of checks, without invoking maintainer mode, is to specify --enable-checks to configure. For more information, see Pre-installation Checks.

This is a standard GNU automake(1) makefile target, although the functions performed are customized for the OpenSS7 Project. This target does not require root privilege.

‘install’

‘install-strip’

The ‘install’ target installs the package by installing each release package. This target also performs some actions similar to the pre- and post-install scripts used by packaging tools such as rpm(1) or dpkg(1). The ‘install-strip’ target strips unnecessary symbols from executables and kernel modules before installing.

This is a standard GNU automake(1) makefile target. This target requires root privilege.

‘installcheck’

All OpenSS7 Project packages provide test scripts for the ‘installcheck’ target. Test scripts are created and run using autotest (part of the autoconf(1) package). Which test suites are run and how extensive they are depends on whether --enable-maintainer-mode was specified to configure. When in maintainer mode, all test suites will be run. When not in maintainer mode, only a few post-install checks will be performed, but the test suites themselves will be installed in /usr/libexec/iperf²⁰ for later use.

This is a standard GNU automake(1) makefile target. This target might require root privilege. Tests requiring root privilege will be skipped when run as a regular user. Tests requiring regular account privileges will be skipped when run as root.

‘retest’

To complement the ‘installcheck’ target above, all OpenSS7 Project packages provide the ‘retest’ target as a means to rerun failed conformance test suite test cases. The ‘retest’ target is provided because some test cases in the test suites have delicate timing considerations that allow them to fail sporadically. Invoking this target will retest the failed cases until no cases that are not expected failures remain.

This is an OpenSS7 Project specific makefile target. As with ‘installcheck’, this target might require root privilege. Tests requiring root privilege will be skipped when run as a regular user. Tests requiring regular account privileges will be skipped when run as root.

‘uninstall’

This target will reverse the steps taken to install the package. This target also performs pre- and post- erase scripts used by packaging tools such as rpm or dpkg. You need to have a configured build directory from which to execute this target, however, you do not need to have compiled any of the files in that build directory.²¹

The ‘uninstall’ target unfortunately removes add-on packages in the same order in which they were installed. This is not good for the OpenSS7 Master Package, where the ‘remove’ target should be used instead.

This is a standard GNU automake(1) makefile target. This target requires root privilege.

‘remove’

This target is like ‘uninstall’ with the exception that it removes add-on packages in the reverse order that installation was performed.²²

This is an OpenSS7 Project specific makefile target. This target requires root privilege.

6.7.1.2 Maintainer Targets

The following targets are targets intended for use by maintainers of the package, or those responsible for release and packaging of a derivative work of the package. Some of these targets are only effective when maintainer mode has been invoked (--enable-maintainer-mode specified to configure.)

‘dist’: Creates a distribution package (tarball) in the top level build directory. OpenSS7 Project packages distribute two archives: a ‘gzip tar’ archive and a ‘bzip tar’ archive. These archives will have the name iperf-2.0.8.tar.gz and iperf-2.0.8.tar.bz2.
This is a standard GNU automake(1) makefile target. This target does not require root privilege.
‘distcheck’: This target is intended for use when releasing the package. It creates the tar(1) archives above and then unpacks the tarball in a source directory, configures in a separate build directory, compiles the package, installs the package in a separate install directory, tests the install package to ensure that some components work, and, finally, uses the unpacked source tree to build another tarball. If you have added or removed files from the package, this is a good way to ensure that everything is still stable for release.
This is a standard GNU automake(1) makefile target. This target does not require root privilege.

6.7.1.3 Clean Targets

‘mostlyclean’: Cleans out most of the files from the compile stage. This target is helpful if you have not enabled dependency tracking and need to recompile with changes.
This is a standard GNU automake(1) makefile target. This target does not require root privilege.
‘clean’: Cleans all the files from the build directory generated during the ‘make [all]’ phase. It does not, however, remove files from the directory left there from the configure run. Use the ‘distclean’ target to remove those too.
This is a standard GNU automake(1) makefile target. This target might require root privilege if the ‘installcheck’ target or the testsuite was invoked with root privilege (leaving files belonging to root).
‘distclean’: This target cleans out the directories left behind by ‘distcheck’ and removes all the configure and generated files from the build directory. This will effectively remove all the files in the build directory, with the except of files that belong to you or some other process.
This is a standard GNU automake(1) makefile target. This target might require root privilege if the ‘installcheck’ target or the testsuite was invoked with root privilege (leaving files belonging to root).
‘maintainer-clean’: This target not only removes files from the build directory, it removes generated files from the source directory as well. Care should be taken when invoking this target, because it removes files generated by the maintainer and distributed with the archive that might require special tools to regenerate. These special tools might only be available to the maintainer.²³ It also means that you probably need a full blown Linux system to rebuild the package. For more information, see Downloading from CVS.
This is a standard GNU automake(1) makefile target. This target might require root privilege if the ‘installcheck’ target or the testsuite was invoked with root privilege (leaving files belonging to root).
‘check-clean’: This target removes log files left behind by the ‘check’ target. By default, the check scripts append to log files in the top level build directory. This target can be used to clean out those log files before the next run.
This is an OpenSS7 Project specific makefile target. This target does not require root privilege.

6.7.1.4 Manual Page Targets

The following targets are used to build, install and uninstall just the manual pages from the distribution. These targets are good for creating a distribution of just the manual pages. When building atop multiple packages, these targets recurse down through each package.

‘mans’: Build all of the manual pages. This involves performing parameter substitution on manual pages and optionally cooking the manual pages if --with-cooked-manpages was requested during configuration.
‘install-mans’: Installs the manual pages under DESTDIR. Specify DESTDIR to place the manual pages wherever you see fit. If DESTDIR is not specified on the command line, the manual pages will be installed in the normal installation directory.
‘uninstall-mans’: Uninstalls the manual pages from DESTDIR. Specify DESTDIR to indicate where to remove the manual pages from. If DESTDIR is not specified on the command line, the manual pages will be removed from the normal installation directory.

6.7.1.5 Release Targets

The following are targets used to generate complete releases into the package distribution directory. These are good for unattended and NFS builds, which is what I use them for. Also, when building from atop multiple packages, these targets also recurse down through each package.

‘release’: Build all of the things necessary to generate a release. On an rpm(1) system this is the distribution archives, the source rpm, and the architecture dependent and architecture independent binary rpms. All items are placed in the package distribution directory that can be specified with the --with-pkg-distdir=DIR option to configure.
This is an OpenSS7 Project specific makefile target. This target does not require root privilege.
‘forced-release’: The ‘release’ target will not regenerate any files that already exist in the package distribution directory. This forced target will.
This is an OpenSS7 Project specific makefile target. This target does not require root privilege.
‘release-sign’: You will be prompted for a password, unless to specify it to make with the GNUPGPASS variable. For unattended or non-interactive builds with signing, you can do that as: ‘make GNUPGPASS=mypasswd release-sign’
This is an OpenSS7 Project specific makefile target. This target does not require root privilege.
‘forced-release-sign’: The ‘release-sign’ target will not regenerate any files that already exist in the package distribution directory. This forced target will.
This is an OpenSS7 Project specific makefile target. This target does not require root privilege.
‘release-clean’: This target will remove all distribution files for the current package from the package distribution directory.
This is an OpenSS7 Project specific makefile target. This target does not require root privilege.

6.7.1.6 Logging Targets

For convenience, to log the output of a number of targets to a file, log targets are defined. The log file itself is used as the target to make, but make invokes the target minus a .log suffix. So, for example, to log the results of target ‘foo’, invoke the target ‘foo.log’. The only target that this does not apply to is ‘compile.log’. When you invoke the target ‘compile.log’ a simple automake(1) is invoked and logged to the file compile.log. The ‘foo.log’ rule applies to all other targets. This does not work for all targets, just a selected few.²⁴ Following are the logging targets:

Common Logging Targets

Common logging targets correspond to normal user automake(1) makefile targets as follows:

‘compile.log’: This is an OpenSS7 Project specific makefile target, but it invokes the standard GNU automake(1) makefile target ‘[all]’.
‘check.log’: This is an OpenSS7 Project specific makefile target, but it invokes the standard GNU automake(1) makefile target ‘check’.
‘install.log’: This is an OpenSS7 Project specific makefile target, but it invokes the standard GNU automake(1) makefile target ‘install’.
‘installcheck.log’: This is an OpenSS7 Project specific makefile target, but it invokes the standard GNU automake(1) makefile target ‘installcheck’.
‘uninstall.log’: This is an OpenSS7 Project specific makefile target, but it invokes the standard GNU automake(1) makefile target ‘uninstall’.
‘remove.log’: This is an OpenSS7 Project specific makefile target, that invokes the OpenSS7 Project ‘remove’ target.

Maintainer Logging Targets

Maintainer logging targets correspond to maintainer mode automake(1) makefile targets as follows:

‘dist.log’: This is an OpenSS7 Project specific makefile target, but it invokes the standard GNU automake(1) makefile target ‘dist’.
‘distcheck.log’: This is an OpenSS7 Project specific makefile target, but it invokes the standard GNU automake(1) makefile target ‘distcheck’.
‘srpm.log’: This is an OpenSS7 Project specific makefile target, that invokes the OpenSS7 Project ‘srpm’ target.
‘rebuild.log’: This is an OpenSS7 Project specific makefile target, that invokes the OpenSS7 Project ‘rebuild’ target.
‘resign.log’: This is an OpenSS7 Project specific makefile target, that invokes the OpenSS7 Project ‘resign’ target.
‘release.log’: This is an OpenSS7 Project specific makefile target, that invokes the OpenSS7 Project ‘release’ target.
‘release-sign.log’: This is an OpenSS7 Project specific makefile target, that invokes the OpenSS7 Project ‘release-sign’ target.

If you want to add one, simply add it to LOGGING_TARGETS in Makefile.am.

6.7.1.7 Problem Report Targets

To ease problem report generation, all logging targets will automatically generate a problem report suitable for mailing in the file target.pr for target ‘target.log’. This problem report file is in the form of an email and can be sent using the included send-pr script or by invoking the ‘send-pr’ makefile target.

There are two additional problem report targets:

‘pr’: The ‘pr’ target is for independently generating a problem report outside of the build or installation process. The target will automatically generate a problem report skeleton suitable for editing and mailing in the file problem.pr. This problem report file is in the form of an email and can be edited and sent directly, or sent using the included send-pr script or by invoking the ‘send-pr’ target.
This is an OpenSS7 Project specific makefile target. This target does not require root privilege.
‘send-pr’: The ‘send-pr’ target is for finalizing and mailing a problem report generated either inside or outside the build and installation process. The target will automatically finalize and mail the problem.pr problem report if it has changed since the last time that ‘send-pr’ was invoked.
This is an OpenSS7 Project specific makefile target. This target does not require root privilege (unless the problem report file was generated as root).

6.7.1.8 Release Archive Targets

The following targets are used to generate and clean distribution archive and signature files. Whereas the ‘dist’ target affects archives in the top build directory, the ‘release-archive’ targets affects archives in the package distribution directory (either the top build directory or that specified with --with-pkg-distdir=DIR to configure).

You can change the directory to which packages are distributed by using the --with-pkg-distdir=DIR option to configure. The default directory is the top build directory.

‘release-archives’

This target creates the distribution archive files if they have not already been created. This not only runs the ‘dist’ target, but also copies the files to the distribution directory, which, by default is the top build directory.

The files generated are named:

iperf-2.0.8.tar.gz and iperf-2.0.8.tar.bz2

You can change this distribution directory with the --with-pkg-distdir option to configure. See ‘./configure --help’ for more details on options.

This is an OpenSS7 Project specific makefile target. This target does not require root privilege.

‘release-sign-archives’

This target is like ‘release-archives’, except that it also signs the archives using a GPG detached signature. You will be prompted for a password unless you pass the GNUPGPASS variable to make. For automated or unattended builds, pass the GNUPGPASS variable like so:

‘make GNUPGPASS=mypasswd release-sign-archives’

Signature files will be named:

iperf-2.0.8.tar.gz.asc and iperf-2.0.8.tar.bz2.asc

These files will be moved to the package distribution directory with the plain text archives.

This is an OpenSS7 Project specific makefile target. This target does not require root privilege.

‘release-clean-archives’

This target will clean the release archives and signature files from the package distribution directory.

This is an OpenSS7 Project specific makefile target. This target does not require root privilege.

6.7.1.9 RPM Build Targets

On rpm(1) systems, or systems sporting rpm packaging tools, the following targets are used to generate rpm(1) release packages. The epoch and release number can be controlled by the contents of the .rpmepoch and .rpmrelease files, or with the --with-rpm-epoch=EPOCH and --with-rpm-release=RELEASE options to configure. See ‘configure --help’ for more information on options. We always use release number ‘1’. You can use release numbers above ‘1’.

‘srpm’

This target generates the source rpm for the package (without signing the source rpm). The source rpm will be named: iperf-2.0.8-1.srpm.

This is an OpenSS7 Project specific makefile target. This target does not require root privilege.

‘rpms’

This target is responsible for generating all of the package binary rpms for the architecture. The binary rpms will be named:

iperf-*-2.0.8-1.*.rpm

where the stars indicate the subpackage and the architecture. Both the architecture specific subpackages (binary objects) and the architecture independent (.noarch) subpackages will be built unless the the former was disabled with the option --disable-arch, or the later with the option --disable-indep, passed to configure.

This is an OpenSS7 Project specific makefile target. This target does not require root privilege.

‘sign’

‘srpm-sign’

These two targets are the same. When invoked, they will add a signature to the source rpm file, provided that the file does not already have a signature. You will be prompted for a password if a signature is required. Automated or unattended builds can be achieved by using the emake expect script, included in ${srcdir}/scripts/emake.

This is an OpenSS7 Project specific makefile target. This target does not require root privilege.

‘rebuild’

This target accepts searches out a list of kernel names from the ${DESTDIR}/lib/modules directory and builds rpms for those kernels and for each of a set of architectures given in the AM_RPMTARGETS variable to make. This is convenience target for building a group of rpms on a given build machine.

This is an OpenSS7 Project specific makefile target. This target does not require root privilege.

‘resign’

This target will search out and sign, with a GPG signature, the source rpm, and all of the binary rpms for this package that can be found in the package distribution directory. This target will prompt for a GPG password. Automated or unattended builds can be achieved with the emake expect script located here: ${srcdir}/scripts/emake.

This is an OpenSS7 Project specific makefile target. This target does not require root privilege.

6.7.1.10 Debian Build Targets

On Debian systems, or systems sporting Debian packaging tools, the following targets are used to generate Debian release packages. The release number can be controlled by the contents of the .debrelease file, or with the --with-debrelease=RELEASENUMBER option to configure. See ‘configure --help’ for more information on options.

‘dsc’: This target will build the Debian source change package (.dsc file). We use release number ‘0’ so that the entire tarball is included in the dsc file. You can use release number ‘1’ for the same purposes. Release numbers above ‘1’ will not include the entire tarball. The .dsc file will be named: iperf_2.0.8-0.dsc.
This is an OpenSS7 Project specific makefile target. This target does not require root privilege.
‘sigs’: This target signs the .deb files. You will be prompted for a password, unless to specify it to make with the GNUPGPASS variable.
This is an OpenSS7 Project specific makefile target. This target does not require root privilege.
‘debs’: This target will build the Debian binary package (.deb file) from the .dsc created above. (This target will also create the .dsc if it has not been created already.) The subpackage .deb files will be named: iperf-*_2.0.8-0_*.deb, where the stars indicate the subpackage and the architecture.
This is an OpenSS7 Project specific makefile target. This target does not require root privilege.
‘csig’: This target signs the .dsc file. You will be prompted for a password, unless to specify it to make with the GNUPGPASS variable.
This is an OpenSS7 Project specific makefile target. This target does not require root privilege.

6.7.1.11 Documentation Targets

On systems that have doxygen(1) documentation tool, the following targets are used to generate doxygen html documentation:

‘doxy’: This target generates doxygen(1) documetnation from suitably marked sources. File containing the necessary documentation marks are discovered automatically by configure. Doxygen documentation can be generated bus is not distributed. Documentation is cerated in the subdirectory doc/html.

7 Troubleshooting

7.1 Test Suites

7.1.1 Pre-installation Checks

Most OpenSS7 packages, including the OpenSS7 IPERF Utility package, ship with pre-installation checks integral to the build system. Pre-installation checks include check scripts that are shipped in the scripts subdirectory as well as specialized make targets that perform the checks.

When building and installing the package from RPM or DEB source packages (see Building from the Source RPM; and Building from the Debian DSC), a fundamental set of post-compile, pre-installation checks are performed prior to building binary packages. This is performed automatically and does not require any special actions on the part of the user creating binary packages from source packages.

When building and installing the package from tarball (see Building from the Tar Ball; and Installing the Tar Ball), however, pre-installation checks are only performed if specifically invoked by the builder of the package. Pre-installation checks are invoked after building the package and before installing the package. Pre-installation checks are performed by invoking the ‘check’ or ‘check.log’ target to make when building the package, as shown in testsuite:ex0.

     % wget http://www.openss7.org/iperf-2.0.8.tar.bz2
     % tar -xjvf iperf-2.0.8.tar.bz2
     % pushd iperf-2.0.8
     % ./configure
     % make
     % make check  # <------- invoke pre-installation checks
     % popd

Example 7.1: Invoking Pre-Installation Checks

Pre-installation checks fall into two categories: System Checks and Maintenance Checks.

7.1.1.1 Pre-Installation System Checks

System Checks are post-compilation checks that can be performed before installing the package that check to ensure that the compiled objects function and will be successfully installed. When the --enable-maintainer-mode option has not been passed to configure, only System Checks will be performed.

For example, the steps shown in testsuite:ex1 will perform System checks.

     % wget http://www.openss7.org/iperf-2.0.8.tar.bz2
     % tar -xjvf iperf-2.0.8.tar.bz2
     % pushd iperf-2.0.8
     % ./configure
     % make
     % make check  # <------ invokes System pre-installation checks
     % popd

Example 7.2: Invoking System Checks

7.1.1.2 Pre-Installation Maintenance Checks

Maintenance Checks include all System Checks, but also checks to ensure that the kernel modules, applications programs, header files, development tools, test programs, documentation, and manual pages conform to OpenSS7 standards. When the --enable-maintainer-mode option has been passed to configure, Maintenance Checks will be performed.

For example, the steps shown in testsuite:ex2 will perform Maintenance checks.

     % wget http://www.openss7.org/iperf-2.0.8.tar.bz2
     % tar -xjvf iperf-2.0.8.tar.bz2
     % pushd iperf-2.0.8
     % ./configure --enable-maintainer-mode
     % make
     % make check  # <------ invokes Maintenance pre-installation checks
     % popd

Example 7.3: Invoking Maintenance Checks

7.1.1.3 Specific Pre-Installation Checks

A number of check scripts are provided in the scripts subdirectory of the distribution that perform both System and Maintenance checks. These are as follows:

check_commands

This check performs both System and Maintenance checks.

When performing System tests, the following tests are performed:

Unless cross-compiling, or unless a program is included in AM_INSTALLCHECK_STD_OPTIONS_EXEMPT every program in bin_PROGRAMS, sbin_PROGRAMS, and libexec_PROGRAMS is tested to ensure that the --help, --version, and --copying options are accepted. When cross-compiling is is not possible to execute cross-compiled binaries, and these checks are skipped in that case.

Script executables, on the other hand, can be executed on the build host, so, unless listed in AM_INSTALLCHECK_STD_OPTIONS_EXEMPT, every program in dist_bit_SCRIPTS, dist_sbin_SCRIPTS, and pkglibexec_SCRIPTS are tested to ensure that the --help, --version, and --copying options are accepted.

When performing Maintenance tests, check_commands also checks to ensure that a manual page exists in section 1 for every executable binary or script that will be installed from bin_PROGRAMS and dist_bin_SCRIPTS. It also checks to ensure that a manual page exists in section 8 for every executable binary or script that will be installed from sbin_PROGRAMS, dist_sbin_SCRIPTS, libexec_PROGRAMS, and pkglibexec_SCRIPTS.

check_decls

This check only performs Maintenance checks.

It collects the results from the check_libs, check_modules and check_headers check scripts and tests to ensure every declaration of a function prototype or external variable contained in installed header files has a corresponding exported symbol from either a to be installed shared object library or a to be installed kernel module. Declarations are exempted from this requirement if their identifiers have been explicitly added to the EXPOSED_SYMBOL variable. If WARN_EXCESS is set to ‘yes’, then the check script will only warn when excess declarations exist (without a corresponding exported symbol); otherwise, the check script will generate an error and the check will fail.

check_headers

This check only performs Maintenance checks.

When performing Maintenance tests, it identifies all of the declarations included in to be installed header files. It then checks to ensure that a manual page exists in sections 2, 3, 7 or 9, as appropriate, for the type of declaration. It also checks to see if a manual page source file exists in the source directory for a declaration that has not been included in the distribution. Function or prototype declarations that do not have a manual page in sections 2, 3, or 9 will cause the check to fail. Other declarations (‘variable’, ‘externvar’, ‘macro’, ‘enumerate’, ‘enum’, ‘struct’, ‘union’, ‘typedef’, ‘member’, etc.) will only warn if a manual page does not exist, but will not fail the check.

check_libs

This check only performs Maintenance checks.

When performing Maintenance tests, it checks that each exported symbol in each to be installed shared object library has a manual page in section 3. It also checks that each exported symbol has a ‘function’, ‘prototype’ or ‘externvar’ declaration in the to be installed header files. A missing declaration or manual page will cause this check to fail.

check_mans

This check only performs Maintenance checks.

When performing Maintenance tests, it checks that to be install manual pages can be formatted for display without any errors or warnings from the build host man program. It also checks that required headings exist for manual pages according to the section in which the manual page will be installed. It warns if recommended headings are not included in the manual pages. Because some RPM distributions have manual pages that might conflict with the package manual pages, this check script also checks for conflicts with installed manual pages on the build host. This check script also checks to ensure that all to be installed manual pages are used in some fashion, that is, they have a declaration, or exported symbol, or are the name of a kernel module or STREAMS module or driver, possibly capitalized.

Note that checking for conflicts with the build host should probably be included in the System checks (because System checks are performed before the source RPM %install scriptlet).

check_modules

This check performs both System and Maintenance checks.

When performing System tests, it checks each to be installed kernel module to ensure that all undefined symbols can be resolved to either the kernel or another module. It also checks whether an exported or externally declared symbol conflicts with an exported or externally declared symbol present in the kernel or another module.²⁵

When performing Maintenance tests, this check script tests that each to be installed kernel module has a manual page in section 9 and that each exported symbol that does not begin with an underscore, and that belongs to an exported function or exported variable, has a manual page in section 9. It also checks to ensure that each exported symbol that does not begin with an underscore, and that belongs to an exported function or exported variable, has a ‘function’, ‘prototype’ or ‘externvar’ declaration in the to be installed header files.

check_streams

This check performs only Maintenance checks.

When performing Maintenance tests, it checks that for each configured STREAMS module or driver, or device node, that a manual page exists in section 4 or section 7 as appropriate.

The output of the pre-installation tests are fairly self explanatory. Each check script saves some output to name.log, where name is the name of the check script as listed above. A summary of the results of the test are display to standard output and can also be captured to the check.log file if the ‘check.log’ target is used instead of the ‘check’ target to make.

Because the check scripts proliferate name.log files throughout the build directory, a ‘make check-clean’ make target has be provided to clean them out. ‘make check-clean’ should be run before each successive run of ‘make check’.

7.1.2 Post-installation Checks

Most OpenSS7 packages ship with a compatibility and conformance test suite built using the ‘autotest’ capabilities of ‘autoconf’. These test suites act as a wrapper for the compatibility and conformance test programs that are shipped with the package.

Unlike the pre-installation checks, the post-installation checks are always run complete. The only check that post-installation test scripts perform is to test whether they have been invoked with root privileges or not. When invoked as root, or as a plain user, some tests might be skipped that require root privileges, or that require plain user privileges, to complete successfully.

7.1.2.1 Running Test Suites

There are several ways of invoking the conformance test suites:

The test suites can be run after installation of the package by invoking the ‘make installcheck’ or ‘make installcheck.log’ target. Some packages require that root privileges be acquired before invoking the package.
The test suites can be run from the distribution subdirectory after installation of the package by invoking the testsuite shell script directly.
The test suites can be run standalone from the libexec (/usr/libexec) installation directory by invoking the testsuite shell script directly.

Typical steps for invoking the test suites directly from make are shown in testsuite:ex3.

     % wget http://www.openss7.org/iperf-2.0.8.tar.bz2
     % tar -xjvf iperf-2.0.8.tar.bz2
     % pushd iperf-2.0.8
     % ./configure
     % make
     % make check  # <------ invokes System pre-installation checks
     % make install
     % sudo make installcheck # <------- invokes post-installation tests
     % popd

Example 7.4: Invoking System Checks

When performing post-installation checks for the purposes of generating a problem report, the checks should always be performed from the build directory, either with ‘make installcheck’ or by invoking testsuite directly from the tests subdirectory of the build directory. This ensures that all of the information known to configure and pertinent to the configuration of the system for which a test case failed, will be collected in the resulting testsuite.log file deposited upon test suite failure in the tests directory. This testsuite.log file can then be attached as part of the problem report and provides rich details to maintainers of the package. See also See Problem Reports, below.

Typical steps for invoking and installed testsuite standalone are shown in testsuite:ex4.

     % [sudo] /usr/libexec/iperf/testsuite

Example 7.5: Invoking testsuite Directly

When invoked directly, testsuite will generate a testsuite.log file in the current directory, and a testsuite.dir directory of failed tests cases and debugging scripts. For generating a problem report for failed test cases, see Stand Alone Problem Reports.

7.2 Problem Reports

7.2.1 Problem Report Guidelines

Problem reports in the following categories should include a log file as indicated in the table below:

‘./configure’: A problem with the configuration process occurs that causes the ‘./configure’ command to fail. The problem report must include the config.log file that was generated by configure.
‘make compile.log’: A problem with the build process occurs that causes the ‘make’ command to fail. Perform ‘make clean’ and then ‘make compile.log’ and attach the config.log and compile.log files to the problem report.
‘make check.log’: A problem occurs with the ‘make check’ target that causes it to fail. Perform ‘make check-clean check.log’ and attach the config.log, compile.log and check.log files to the problem report.
‘sudo make install.log’: A problem occurs with ‘sudo make install’ that causes it to fail. Perform ‘sudo make uninstall’ and ‘sudo make install.log’ and attach the config.log, compile.log, check.log, and install.log files to the problem report.
‘[sudo] make installcheck.log’: A problem occurs with the ‘make installcheck’ target that causes the test suite to fail. Attach the resulting tests/testsuite.log and installcheck.log file to the problem report. There is no need to attach the other files as they are included in tests/testsuite.log.
‘[sudo] make uninstall.log’: A problem occurs with the ‘make uninstall’ target that causes the test suite to fail. Perform ‘sudo make uninstall.log’ and attach the config.log, compile.log, check.log, install.log, installcheck.log, tests/testsuite.log and uninstall.log file to the problem report.
‘[sudo] make remove.log’: A problem occurs with the ‘make remove’ target that causes the test suite to fail. Perform ‘sudo make remove.log’ and attach the config.log, compile.log, check.log, install.log, installcheck.log, tests/testsuite.log and remove.log file to the problem report.

For other problems that occur during the use of the OpenSS7 IPERF Utility package, please write a test case for the test suite that recreates the problem if one does not yet exist and provide a test program patch with the problem report. Also include whatever log files are generated by the kernel (cmn_err(9)) or by the strerr(8) or strace(1) facilities (strlog(9)).

7.2.2 Generating Problem Reports

The OpenSS7 Project uses the GNU GNATS system for problem reporting. Although the ‘send-pr’ tool from the GNU GNATS package can be used for bug reporting to the project's GNATS database using electronic mail, it is not always convenient to download and install the GNATS system to gain access to the ‘send-pr’ tool.

Therefore, the OpenSS7 IPERF Utility package provides the ‘send-pr’ shell script that can be used for problem reporting. The ‘send-pr’ shell script can invoked directly and is a work-alike for the GNU ‘send-pr’ tool.

The ‘send-pr’ tool takes the same flags and can be used in the same fashion, however, whereas ‘send-pr’ is an interactive tool²⁶, ‘send-pr’ is also able to perform batch processing. Whereas ‘send-pr’ takes its field information from local databases or from using the ‘query-pr’ C-language program to query a remote database, the ‘send-pr’ tool has the field database internal to the tool.

Problem reports can be generate using make, See Problem Report Targets. An example of how simple it is to generate a problem report is illustrated in autopr:ex0.

     % make pr
     SEND-PR:
     SEND-PR: send-pr:  send-pr was invoked to generate an external report.  An
     SEND-PR: automated problem report has been created in the file named
     SEND-PR: 'problem.pr' in the current directory.  This problem report can
     SEND-PR: be sent to [email protected] by calling this script as
     SEND-PR: '/home/brian/os7/scripts/send-pr --file="problem.pr"'.
     SEND-PR:
     SEND-PR: It is possible to edit some of the fields before sending on the
     SEND-PR: problem report.  Please remember that there is NO WARRANTY.  See
     SEND-PR: the file 'COPYING' in the top level directory.
     SEND-PR:
     SEND-PR: Please do not send confidential information to the bug report
     SEND-PR: address.  Inspect the file 'problem.pr' for confidential
     SEND-PR: information before mailing.
     SEND-PR:
     % vim problem.pr  # <--- follow instructions at head of file
     % make send-pr

Example 7.6: Invoking Problem Report Generation

Using the ‘make pr’ target to generate a problem report has the advantages that it will assemble any available *.log files in the build directory and attach them to the problem report.

7.2.3 Automatic Problem Reports

The OpenSS7 IPERF Utility package also provides a feature for automatic problem report generation that meets the problem report submission guidelines detailed in the preceding sections.

Whenever a logging makefile target (see Logging Targets) is invoked, if the primary target fails, the send-pr shell script is invoked to automatically generate a problem report file suitable for the corresponding target (as described above under see Problem Report Guidelines). An example is shown in autopr:ex1.

     % make compile.log
     ...
     ...
     make[5]: *** [libXNSdrvs_a-ip.o] Error 1
     make[5]: Leaving directory `/u6/buildel4/strxns'
     make[4]: *** [all-recursive] Error 1
     make[4]: Leaving directory `/u6/buildel4/strxns'
     make[3]: *** [all] Error 2
     make[3]: Leaving directory `/u6/buildel4/strxns'
     make[2]: *** [all-recursive] Error 1
     make[2]: Leaving directory `/u6/buildel4'
     make[1]: *** [all] Error 2
     make[1]: Leaving directory `/u6/buildel4'
     SEND-PR:
     SEND-PR: send-pr:  Make target compile.log failed in the compile stage.  An
     SEND-PR: automated problem report has been created in the file named
     SEND-PR: 'problem.pr' in the current directory.  This problem report can
     SEND-PR: be sent to [email protected] by calling 'make send-pr'.
     SEND-PR:
     SEND-PR: It is possible to edit some of the fields before sending on the
     SEND-PR: problem report.  Please remember that there is NO WARRANTY.  See
     SEND-PR: the file 'COPYING' in the top level directory.
     SEND-PR:
     SEND-PR: Please do not send confidential information to the bug report
     SEND-PR: address.  Inspect the file 'problem.pr' for confidential
     SEND-PR: information before mailing.
     SEND-PR:
     % vim problem.pr  # <--- follow instructions at head of file
     % make send-pr

Example 7.7: Problem Report from Failed Logging Target

7.2.4 Stand Alone Problem Reports

The OpenSS7 IPERF Utility package installs the send-pr script and its configuration file send-pr.config in ${libexecdir}/iperf along with the validation testsuite, see See Test Suites. As with the testsuite, this allows the send-pr script to be used for problem report generation on an installed system that does not have a build directory.

An example of invoking the package testsuite and then generating a problem report for failed cases is shown in autopr:ex2.

     % [sudo] /usr/libexec/iperf/testsuite
     % # test cases failed...
     % /usr/libexec/iperf/send-pr
     SEND-PR:
     SEND-PR: send-pr:  send-pr was invoked to generate an external report.  An
     SEND-PR: automated problem report has been created in the file named
     SEND-PR: 'problem.pr' in the current directory.  This problem report can
     SEND-PR: be sent to [email protected] by calling this script as
     SEND-PR: '/usr/libexec/iperf/send-pr --file problem.pr'.
     SEND-PR:
     SEND-PR: It is possible to edit some of the fields before sending on the
     SEND-PR: problem report.  Please remember that there is NO WARRANTY.  See
     SEND-PR: the file 'COPYING' in the top level directory.
     SEND-PR:
     SEND-PR: Please do not send confidential information to the bug report
     SEND-PR: address.  Inspect the file 'problem.pr' for confidential
     SEND-PR: information before mailing.
     SEND-PR:
     % vim problem.pr  # <--- follow instructions at head of file
     % /usr/libexec/iperf/send-pr --file problem.pr

Example 7.8: Invoking send-pr Directly

The advantage of the approach shown in the example is that the send-pr script is capable of collecting the testsuite.log file and the failed test cases and debugging scripts from the testsuite.dir directory and including them in the problem report, as well as all package pertinent information from the installed send-pr.config.

7.3 Known Problems

The OpenSS7 Project does not ship software with known bugs. All bugs are unknown.

Verified behaviour is that behaviour that has been verified by conformance test suites that are shipped with the OpenSS7 IPERF Utility package.

Unverified behaviour may contain unknown bugs.

Please remember that there is NO WARRANTY.

See also Bugs, or file BUGS in the release directory.

Licenses

University of Illinois License

Distributed Applications Support Team

Iperf Copyright

the University of Illinois

Iperf performance test

Mark Gates

Ajay Tirumala

Jim Ferguson

Jon Dugan

Feng Qin

Kevin Gibbs

National Laboratory for Applied Network Research

National Center for Supercomputing Applications

University of Illinois at Urbana-Champaign

http://www.ncsa.uiuc.edu/

Permission is hereby granted, free of charge, to any person obtaining a copy of this software (Iperf) and associated documentation files (the Software), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimers.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimers in the documentation and/or other materials provided with the distribution.
Neither the names of the University of Illinois, NCSA, nor the names of its contributors may be used to endorse or promote products derived from this Software without specific prior written permission.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE CONTIBUTORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

[email protected] Last modified: Jan 5, 2004

GNU Affero General Public License

The GNU Affero General Public License.

Version 3, 19 November 2007

     Copyright © 2007 Free Software Foundation, Inc. http://fsf.org/
     
     Everyone is permitted to copy and distribute verbatim copies of this
     license document, but changing it is not allowed.

Preamble

The GNU Affero General Public License is a free, copyleft license for software and other kinds of works, specifically designed to ensure cooperation with the community in the case of network server software.

The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, our General Public Licenses are intended to guarantee your freedom to share and change all versions of a program–to make sure it remains free software for all its users.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things.

Developers that use our General Public Licenses protect your rights with two steps: (1) assert copyright on the software, and (2) offer you this License which gives you legal permission to copy, distribute and/or modify the software.

A secondary benefit of defending all users' freedom is that improvements made in alternate versions of the program, if they receive widespread use, become available for other developers to incorporate. Many developers of free software are heartened and encouraged by the resulting cooperation. However, in the case of software used on network servers, this result may fail to come about. The GNU General Public License permits making a modified version and letting the public access it on a server without ever releasing its source code to the public.

The GNU Affero General Public License is designed specifically to ensure that, in such cases, the modified source code becomes available to the community. It requires the operator of a network server to provide the source code of the modified version running there to the users of that server. Therefore, public use of a modified version, on a publicly accessible server, gives the public access to the source code of the modified version.

An older license, called the Affero General Public License and published by Affero, was designed to accomplish similar goals. This is a different license, not a version of the Affero GPL, but Affero has released a new version of the Affero GPL which permits relicensing under this license.

The precise terms and conditions for copying, distribution and modification follow.

TERMS AND CONDITIONS

Definitions.
“This License” refers to version 3 of the GNU Affero General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The resulting work is called a “modified version” of the earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright law, except executing it on a computer or modifying a private copy. Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer network, with no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of user commands or options, such as a menu, a prominent item in the list meets this criterion.
Source Code.
The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among developers working in that language.
The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this context, means a major essential component (kernel, window system, and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to control those activities. However, it does not include the work's System Libraries, or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work. For example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to require, such as by intimate data communication or control flow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
Basic Permissions.
All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright. Those thus making or running the covered works for you must do so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it unnecessary.
Protecting Users' Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing, against the work's users, your or third parties' legal rights to forbid circumvention of technological measures.
Conveying Verbatim Copies.
You may convey verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice; keep intact all notices stating that this License and any non-permissive terms added in accord with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the Program.
You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.
Conveying Modified Source Versions.
You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions:
1. The work must carry prominent notices stating that you modified it, and giving a relevant date.
2. The work must carry prominent notices stating that it is released under this License and any conditions added under section 7. This requirement modifies the requirement in section 4 to “keep intact all notices”.
3. You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along with any applicable section 7 additional terms, to the whole of the work, and all its parts, regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it.
4. If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation's users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate.
Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable Corresponding Source under the terms of this License, in one of these ways:
1. Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the Corresponding Source fixed on a durable physical medium customarily used for software interchange.
2. Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least three years and valid for as long as you offer spare parts or customer support for that product model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a network server at no charge.
3. Convey individual copies of the object code with a copy of the written offer to provide the Corresponding Source. This alternative is allowed only occasionally and noncommercially, and only if you received the object code with such an offer, in accord with subsection 6b.
4. Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object code. If the place to copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts the Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these requirements.
5. Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and Corresponding Source of the work are being offered to the general public at no charge under subsection 6d.
A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the object code work.
A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage. For a particular product received by a particular user, “normally used” refers to a typical or common use of that class of product, regardless of the status of the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product regardless of whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified versions of a covered work in that User Product from a modified version of its Corresponding Source. The information must suffice to ensure that the continued functioning of the modified object code is in no case prevented or interfered with solely because modification has been made.
If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the right of possession and use of the User Product is transferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction is characterized), the Corresponding Source conveyed under this section must be accompanied by the Installation Information. But this requirement does not apply if neither you nor any third party retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates for a work that has been modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying.
Additional Terms.
“Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire Program remains governed by this License without regard to the additional permissions.
When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. (Additional permissions may be written to require their own removal in certain cases when you modify the work.) You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement the terms of this License with terms:
1. Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or
2. Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works containing it; or
3. Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different from the original version; or
4. Limiting the use for publicity purposes of names of licensors or authors of the material; or
5. Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or
6. Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose on those licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by the terms of that license document, provided that the further restriction does not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or a notice indicating where to find the applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above requirements apply either way.
Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11).
However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright holder explicitly and finally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some reasonable means, this is the first time you have received notice of violation of this License (for any work) from that copyright holder, and you cure the violation prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this License. If your rights have been terminated and not permanently reinstated, you do not qualify to receive new licenses for the same material under section 10.
Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating a covered work, you indicate your acceptance of this License to do so.
Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject to this License. You are not responsible for enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party's predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it.
Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called the contributor's “contributor version”.
A contributor's “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired, that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control” includes the right to grant patent sublicenses in a manner consistent with the requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor's essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to copy, free of charge and under the terms of this License, through a publicly available network server or other readily accessible means, then you must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your recipient's use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.
A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically granted under this License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the extent of your activity of conveying the work, and under which the third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent license (a) in connection with copies of the covered work conveyed by you (or copies made from those copies), or (b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent license was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under applicable patent law.
No Surrender of Others' Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty for further conveying from those to whom you convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program.
Remote Network Interaction; Use with the GNU General Public License.
Notwithstanding any other provision of this License, if you modify the Program, your modified version must prominently offer all users interacting with it remotely through a network (if your version supports such interaction) an opportunity to receive the Corresponding Source of your version by providing access to the Corresponding Source from a network server at no charge, through some standard or customary means of facilitating copying of software. This Corresponding Source shall include the Corresponding Source for any work covered by version 3 of the GNU General Public License that is incorporated pursuant to the following paragraph.
Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue to apply to the part which is the covered work, but the work with which it is combined will remain governed by version 3 of the GNU General Public License.
Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU Affero General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU Affero General Public License “or any later version” applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the GNU Affero General Public License, you may choose any version ever published by the Free Software Foundation.
If the Program specifies that a proxy can decide which future versions of the GNU Affero General Public License can be used, that proxy's public statement of acceptance of a version permanently authorizes you to choose that version for the Program.
Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version.
Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply local law that most closely approximates an absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of liability accompanies a copy of the Program in return for a fee.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.

To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively state the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found.

     one line to give the program's name and a brief idea of what it does.
     Copyright (C) year name of author
     
     This program is free software: you can redistribute it and/or modify
     it under the terms of the GNU Affero General Public License as published by
     the Free Software Foundation, either version 3 of the License, or (at
     your option) any later version.
     
     This program is distributed in the hope that it will be useful, but
     WITHOUT ANY WARRANTY; without even the implied warranty of
     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
     Affero General Public License for more details.
     
     You should have received a copy of the GNU Affero General Public License
     along with this program.  If not, see http://www.gnu.org/licenses/.

Also add information on how to contact you by electronic and paper mail.

If your software can interact with users remotely through a network, you should also make sure that it provides a way for users to get its source. For example, if your program is a web application, its interface could display a “Source” link that leads users to an archive of the code. There are many ways you could offer source, and different solutions will be better for different programs; see section 13 for the specific requirements.

You should also get your employer (if you work as a programmer) or school, if any, to sign a “copyright disclaimer” for the program, if necessary. For more information on this, and how to apply and follow the GNU AGPL, see http://www.gnu.org/licenses/.

GNU General Public License

GNU GENERAL PUBLIC LICENSE

Version 3, 29 June 2007

     Copyright © 2007 Free Software Foundation, Inc. http://fsf.org/
     
     Everyone is permitted to copy and distribute verbatim copies of this
     license document, but changing it is not allowed.

Preamble

The GNU General Public License is a free, copyleft license for software and other kinds of works.

The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change all versions of a program–to make sure it remains free software for all its users. We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work released this way by its authors. You can apply it to your programs, too.

To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it.

For the developers' and authors' protection, the GPL clearly explains that there is no warranty for this free software. For both users' and authors' sake, the GPL requires that modified versions be marked as changed, so that their problems will not be attributed erroneously to authors of previous versions.

Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users' freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to prohibit the practice for those products. If such problems arise substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom of users.

Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on general-purpose computers, but in those that do, we wish to avoid the special danger that patents applied to a free program could make it effectively proprietary. To prevent this, the GPL assures that patents cannot be used to render the program non-free.

The precise terms and conditions for copying, distribution and modification follow.

TERMS AND CONDITIONS

Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The resulting work is called a “modified version” of the earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright law, except executing it on a computer or modifying a private copy. Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer network, with no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of user commands or options, such as a menu, a prominent item in the list meets this criterion.
Source Code.
The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among developers working in that language.
The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this context, means a major essential component (kernel, window system, and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to control those activities. However, it does not include the work's System Libraries, or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work. For example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to require, such as by intimate data communication or control flow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
Basic Permissions.
All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright. Those thus making or running the covered works for you must do so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it unnecessary.
Protecting Users' Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing, against the work's users, your or third parties' legal rights to forbid circumvention of technological measures.
Conveying Verbatim Copies.
You may convey verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice; keep intact all notices stating that this License and any non-permissive terms added in accord with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the Program.
You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.
Conveying Modified Source Versions.
You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions:
1. The work must carry prominent notices stating that you modified it, and giving a relevant date.
2. The work must carry prominent notices stating that it is released under this License and any conditions added under section 7. This requirement modifies the requirement in section 4 to “keep intact all notices”.
3. You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along with any applicable section 7 additional terms, to the whole of the work, and all its parts, regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it.
4. If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation's users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate.
Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable Corresponding Source under the terms of this License, in one of these ways:
1. Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the Corresponding Source fixed on a durable physical medium customarily used for software interchange.
2. Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least three years and valid for as long as you offer spare parts or customer support for that product model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a network server at no charge.
3. Convey individual copies of the object code with a copy of the written offer to provide the Corresponding Source. This alternative is allowed only occasionally and noncommercially, and only if you received the object code with such an offer, in accord with subsection 6b.
4. Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object code. If the place to copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts the Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these requirements.
5. Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and Corresponding Source of the work are being offered to the general public at no charge under subsection 6d.
A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the object code work.
A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage. For a particular product received by a particular user, “normally used” refers to a typical or common use of that class of product, regardless of the status of the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product regardless of whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified versions of a covered work in that User Product from a modified version of its Corresponding Source. The information must suffice to ensure that the continued functioning of the modified object code is in no case prevented or interfered with solely because modification has been made.
If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the right of possession and use of the User Product is transferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction is characterized), the Corresponding Source conveyed under this section must be accompanied by the Installation Information. But this requirement does not apply if neither you nor any third party retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates for a work that has been modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying.
Additional Terms.
“Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire Program remains governed by this License without regard to the additional permissions.
When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. (Additional permissions may be written to require their own removal in certain cases when you modify the work.) You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement the terms of this License with terms:
1. Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or
2. Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works containing it; or
3. Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different from the original version; or
4. Limiting the use for publicity purposes of names of licensors or authors of the material; or
5. Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or
6. Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose on those licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by the terms of that license document, provided that the further restriction does not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or a notice indicating where to find the applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above requirements apply either way.
Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11).
However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright holder explicitly and finally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some reasonable means, this is the first time you have received notice of violation of this License (for any work) from that copyright holder, and you cure the violation prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this License. If your rights have been terminated and not permanently reinstated, you do not qualify to receive new licenses for the same material under section 10.
Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating a covered work, you indicate your acceptance of this License to do so.
Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject to this License. You are not responsible for enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party's predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it.
Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called the contributor's “contributor version”.
A contributor's “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired, that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control” includes the right to grant patent sublicenses in a manner consistent with the requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor's essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to copy, free of charge and under the terms of this License, through a publicly available network server or other readily accessible means, then you must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your recipient's use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.
A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically granted under this License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the extent of your activity of conveying the work, and under which the third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent license (a) in connection with copies of the covered work conveyed by you (or copies made from those copies), or (b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent license was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under applicable patent law.
No Surrender of Others' Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty for further conveying from those to whom you convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program.
Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU Affero General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue to apply to the part which is the covered work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction through a network will apply to the combination as such.
Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General Public License “or any later version” applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any version ever published by the Free Software Foundation.
If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy's public statement of acceptance of a version permanently authorizes you to choose that version for the Program.
Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version.
Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply local law that most closely approximates an absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of liability accompanies a copy of the Program in return for a fee.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Programs

     one line to give the program's name and a brief idea of what it does.
     Copyright (C) year name of author
     
     This program is free software: you can redistribute it and/or modify
     it under the terms of the GNU General Public License as published by
     the Free Software Foundation, either version 3 of the License, or (at
     your option) any later version.
     
     This program is distributed in the hope that it will be useful, but
     WITHOUT ANY WARRANTY; without even the implied warranty of
     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
     General Public License for more details.
     
     You should have received a copy of the GNU General Public License
     along with this program.  If not, see http://www.gnu.org/licenses/.

Also add information on how to contact you by electronic and paper mail.

If the program does terminal interaction, make it output a short notice like this when it starts in an interactive mode:

     program Copyright (C) year name of author
     This program comes with ABSOLUTELY NO WARRANTY; for details type ‘show w’.
     This is free software, and you are welcome to redistribute it
     under certain conditions; type ‘show c’ for details.

The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General Public License. Of course, your program's commands might be different; for a GUI interface, you would use an “about box”.

The GNU General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License. But first, please read http://www.gnu.org/philosophy/why-not-lgpl.html.

GNU Lesser General Public License

GNU LESSER GENERAL PUBLIC LICENSE

Version 3, 29 June 2007

     Copyright © 2007 Free Software Foundation, Inc. http://fsf.org/
     
     Everyone is permitted to copy and distribute verbatim copies of this
     license document, but changing it is not allowed.

TERMS AND CONDITIONS

This version of the GNU Lesser General Public License incorporates the terms and conditions of version 3 of the GNU General Public License, supplemented by the additional permissions listed below.

Additional Definitions.
As used herein, “this License” refers to version 3 of the GNU Lesser General Public License, and the “GNU GPL” refers to version 3 of the GNU General Public License.
“The Library” refers to a covered work governed by this License, other than an Application or a Combined Work as defined below.
An “Application” is any work that makes use of an interface provided by the Library, but which is not otherwise based on the Library. Defining a subclass of a class defined by the Library is deemed a mode of using an interface provided by the Library.
A “Combined Work” is a work produced by combining or linking an Application with the Library. The particular version of the Library with which the Combined Work was made is also called the “Linked Version”.
The “Minimal Corresponding Source” for a Combined Work means the Corresponding Source for the Combined Work, excluding any source code for portions of the Combined Work that, considered in isolation, are based on the Application, and not on the Linked Version.
The “Corresponding Application Code” for a Combined Work means the object code and/or source code for the Application, including any data and utility programs needed for reproducing the Combined Work from the Application, but excluding the System Libraries of the Combined Work.
Exception to Section 3 of the GNU GPL.
You may convey a covered work under sections 3 and 4 of this License without being bound by section 3 of the GNU GPL.
Conveying Modified Versions.
If you modify a copy of the Library, and, in your modifications, a facility refers to a function or data to be supplied by an Application that uses the facility (other than as an argument passed when the facility is invoked), then you may convey a copy of the modified version:
1. under this License, provided that you make a good faith effort to ensure that, in the event an Application does not supply the function or data, the facility still operates, and performs whatever part of its purpose remains meaningful, or
2. under the GNU GPL, with none of the additional permissions of this License applicable to that copy.
Object Code Incorporating Material from Library Header Files.
The object code form of an Application may incorporate material from a header file that is part of the Library. You may convey such object code under terms of your choice, provided that, if the incorporated material is not limited to numerical parameters, data structure layouts and accessors, or small macros, inline functions and templates (ten or fewer lines in length), you do both of the following:
1. Give prominent notice with each copy of the object code that the Library is used in it and that the Library and its use are covered by this License.
2. Accompany the object code with a copy of the GNU GPL and this license document.
Combined Works.
You may convey a Combined Work under terms of your choice that, taken together, effectively do not restrict modification of the portions of the Library contained in the Combined Work and reverse engineering for debugging such modifications, if you also do each of the following:
1. Give prominent notice with each copy of the Combined Work that the Library is used in it and that the Library and its use are covered by this License.
2. Accompany the Combined Work with a copy of the GNU GPL and this license document.
3. For a Combined Work that displays copyright notices during execution, include the copyright notice for the Library among these notices, as well as a reference directing the user to the copies of the GNU GPL and this license document.
4. Do one of the following:
  1. Convey the Minimal Corresponding Source under the terms of this License, and the Corresponding Application Code in a form suitable for, and under terms that permit, the user to recombine or relink the Application with a modified version of the Linked Version to produce a modified Combined Work, in the manner specified by section 6 of the GNU GPL for conveying Corresponding Source.
  2. Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (a) uses at run time a copy of the Library already present on the user's computer system, and (b) will operate properly with a modified version of the Library that is interface-compatible with the Linked Version.
5. Provide Installation Information, but only if you would otherwise be required to provide such information under section 6 of the GNU GPL, and only to the extent that such information is necessary to install and execute a modified version of the Combined Work produced by recombining or relinking the Application with a modified version of the Linked Version. (If you use option 4d0, the Installation Information must accompany the Minimal Corresponding Source and Corresponding Application Code. If you use option 4d1, you must provide the Installation Information in the manner specified by section 6 of the GNU GPL for conveying Corresponding Source.)
Combined Libraries.
You may place library facilities that are a work based on the Library side by side in a single library together with other library facilities that are not Applications and are not covered by this License, and convey such a combined library under terms of your choice, if you do both of the following:
1. Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities, conveyed under the terms of this License.
2. Give prominent notice with the combined library that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work.
Revised Versions of the GNU Lesser General Public License.
The Free Software Foundation may publish revised and/or new versions of the GNU Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Library as you received it specifies that a certain numbered version of the GNU Lesser General Public License “or any later version” applies to it, you have the option of following the terms and conditions either of that published version or of any later version published by the Free Software Foundation. If the Library as you received it does not specify a version number of the GNU Lesser General Public License, you may choose any version of the GNU Lesser General Public License ever published by the Free Software Foundation.
If the Library as you received it specifies that a proxy can decide whether future versions of the GNU Lesser General Public License shall apply, that proxy's public statement of acceptance of any version is permanent authorization for you to choose that version for the Library.

END OF TERMS AND CONDITIONS

GNU Free Documentation License

GNU FREE DOCUMENTATION LICENSE

Version 1.1, March 2000

     Copyright © 2000 Free Software Foundation, Inc.
     59 Temple Place, Suite 330, Boston, MA  02111-1307, USA
     
     Everyone is permitted to copy and distribute verbatim copies
     of this license document, but changing it is not allowed.

PREAMBLE

The purpose of this License is to make a manual, textbook, or other written document free in the sense of freedom: to assure everyone the effective freedom to copy and redistribute it, with or without modifying it, either commercially or noncommercially. Secondarily, this License preserves for the author and publisher a way to get credit for their work, while not being considered responsible for modifications made by others.

This License is a kind of “copyleft”, which means that derivative works of the document must themselves be free in the same sense. It complements the GNU General Public License, which is a copyleft license designed for free software.

We have designed this License in order to use it for manuals for free software, because free software needs free documentation: a free program should come with manuals providing the same freedoms that the software does. But this License is not limited to software manuals; it can be used for any textual work, regardless of subject matter or whether it is published as a printed book. We recommend this License principally for works whose purpose is instruction or reference.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

APPLICABILITY AND DEFINITIONS
This License applies to any manual or other work that contains a notice placed by the copyright holder saying it can be distributed under the terms of this License. The “Document”, below, refers to any such manual or work. Any member of the public is a licensee, and is addressed as “you”.
A “Modified Version” of the Document means any work containing the Document or a portion of it, either copied verbatim, or with modifications and/or translated into another language.
A “Secondary Section” is a named appendix or a front-matter section of the Document that deals exclusively with the relationship of the publishers or authors of the Document to the Document's overall subject (or to related matters) and contains nothing that could fall directly within that overall subject. (For example, if the Document is in part a textbook of mathematics, a Secondary Section may not explain any mathematics.) The relationship could be a matter of historical connection with the subject or with related matters, or of legal, commercial, philosophical, ethical or political position regarding them.
The “Invariant Sections” are certain Secondary Sections whose titles are designated, as being those of Invariant Sections, in the notice that says that the Document is released under this License.
The “Cover Texts” are certain short passages of text that are listed, as Front-Cover Texts or Back-Cover Texts, in the notice that says that the Document is released under this License.
A “Transparent” copy of the Document means a machine-readable copy, represented in a format whose specification is available to the general public, whose contents can be viewed and edited directly and straightforwardly with generic text editors or (for images composed of pixels) generic paint programs or (for drawings) some widely available drawing editor, and that is suitable for input to text formatters or for automatic translation to a variety of formats suitable for input to text formatters. A copy made in an otherwise Transparent file format whose markup has been designed to thwart or discourage subsequent modification by readers is not Transparent. A copy that is not “Transparent” is called “Opaque”.
Examples of suitable formats for Transparent copies include plain ascii without markup, Texinfo input format, LaTeX input format, SGML or XML using a publicly available DTD, and standard-conforming simple HTML designed for human modification. Opaque formats include PostScript, PDF, proprietary formats that can be read and edited only by proprietary word processors, SGML or XML for which the DTD and/or processing tools are not generally available, and the machine-generated HTML produced by some word processors for output purposes only.
The “Title Page” means, for a printed book, the title page itself, plus such following pages as are needed to hold, legibly, the material this License requires to appear in the title page. For works in formats which do not have any title page as such, “Title Page” means the text near the most prominent appearance of the work's title, preceding the beginning of the body of the text.
VERBATIM COPYING
You may copy and distribute the Document in any medium, either commercially or noncommercially, provided that this License, the copyright notices, and the license notice saying this License applies to the Document are reproduced in all copies, and that you add no other conditions whatsoever to those of this License. You may not use technical measures to obstruct or control the reading or further copying of the copies you make or distribute. However, you may accept compensation in exchange for copies. If you distribute a large enough number of copies you must also follow the conditions in section 3.
You may also lend copies, under the same conditions stated above, and you may publicly display copies.
COPYING IN QUANTITY
If you publish printed copies of the Document numbering more than 100, and the Document's license notice requires Cover Texts, you must enclose the copies in covers that carry, clearly and legibly, all these Cover Texts: Front-Cover Texts on the front cover, and Back-Cover Texts on the back cover. Both covers must also clearly and legibly identify you as the publisher of these copies. The front cover must present the full title with all words of the title equally prominent and visible. You may add other material on the covers in addition. Copying with changes limited to the covers, as long as they preserve the title of the Document and satisfy these conditions, can be treated as verbatim copying in other respects.
If the required texts for either cover are too voluminous to fit legibly, you should put the first ones listed (as many as fit reasonably) on the actual cover, and continue the rest onto adjacent pages.
If you publish or distribute Opaque copies of the Document numbering more than 100, you must either include a machine-readable Transparent copy along with each Opaque copy, or state in or with each Opaque copy a publicly-accessible computer-network location containing a complete Transparent copy of the Document, free of added material, which the general network-using public has access to download anonymously at no charge using public-standard network protocols. If you use the latter option, you must take reasonably prudent steps, when you begin distribution of Opaque copies in quantity, to ensure that this Transparent copy will remain thus accessible at the stated location until at least one year after the last time you distribute an Opaque copy (directly or through your agents or retailers) of that edition to the public.
It is requested, but not required, that you contact the authors of the Document well before redistributing any large number of copies, to give them a chance to provide you with an updated version of the Document.
MODIFICATIONS
You may copy and distribute a Modified Version of the Document under the conditions of sections 2 and 3 above, provided that you release the Modified Version under precisely this License, with the Modified Version filling the role of the Document, thus licensing distribution and modification of the Modified Version to whoever possesses a copy of it. In addition, you must do these things in the Modified Version:
1. Use in the Title Page (and on the covers, if any) a title distinct from that of the Document, and from those of previous versions (which should, if there were any, be listed in the History section of the Document). You may use the same title as a previous version if the original publisher of that version gives permission.
2. List on the Title Page, as authors, one or more persons or entities responsible for authorship of the modifications in the Modified Version, together with at least five of the principal authors of the Document (all of its principal authors, if it has less than five).
3. State on the Title page the name of the publisher of the Modified Version, as the publisher.
4. Preserve all the copyright notices of the Document.
5. Add an appropriate copyright notice for your modifications adjacent to the other copyright notices.
6. Include, immediately after the copyright notices, a license notice giving the public permission to use the Modified Version under the terms of this License, in the form shown in the Addendum below.
7. Preserve in that license notice the full lists of Invariant Sections and required Cover Texts given in the Document's license notice.
8. Include an unaltered copy of this License.
9. Preserve the section entitled “History”, and its title, and add to it an item stating at least the title, year, new authors, and publisher of the Modified Version as given on the Title Page. If there is no section entitled “History” in the Document, create one stating the title, year, authors, and publisher of the Document as given on its Title Page, then add an item describing the Modified Version as stated in the previous sentence.
10. Preserve the network location, if any, given in the Document for public access to a Transparent copy of the Document, and likewise the network locations given in the Document for previous versions it was based on. These may be placed in the “History” section. You may omit a network location for a work that was published at least four years before the Document itself, or if the original publisher of the version it refers to gives permission.
11. In any section entitled “Acknowledgments” or “Dedications”, preserve the section's title, and preserve in the section all the substance and tone of each of the contributor acknowledgments and/or dedications given therein.
12. Preserve all the Invariant Sections of the Document, unaltered in their text and in their titles. Section numbers or the equivalent are not considered part of the section titles.
13. Delete any section entitled “Endorsements”. Such a section may not be included in the Modified Version.
14. Do not retitle any existing section as “Endorsements” or to conflict in title with any Invariant Section.
If the Modified Version includes new front-matter sections or appendices that qualify as Secondary Sections and contain no material copied from the Document, you may at your option designate some or all of these sections as invariant. To do this, add their titles to the list of Invariant Sections in the Modified Version's license notice. These titles must be distinct from any other section titles.
You may add a section entitled “Endorsements”, provided it contains nothing but endorsements of your Modified Version by various parties—for example, statements of peer review or that the text has been approved by an organization as the authoritative definition of a standard.
You may add a passage of up to five words as a Front-Cover Text, and a passage of up to 25 words as a Back-Cover Text, to the end of the list of Cover Texts in the Modified Version. Only one passage of Front-Cover Text and one of Back-Cover Text may be added by (or through arrangements made by) any one entity. If the Document already includes a cover text for the same cover, previously added by you or by arrangement made by the same entity you are acting on behalf of, you may not add another; but you may replace the old one, on explicit permission from the previous publisher that added the old one.
The author(s) and publisher(s) of the Document do not by this License give permission to use their names for publicity for or to assert or imply endorsement of any Modified Version.
COMBINING DOCUMENTS
You may combine the Document with other documents released under this License, under the terms defined in section 4 above for modified versions, provided that you include in the combination all of the Invariant Sections of all of the original documents, unmodified, and list them all as Invariant Sections of your combined work in its license notice.
The combined work need only contain one copy of this License, and multiple identical Invariant Sections may be replaced with a single copy. If there are multiple Invariant Sections with the same name but different contents, make the title of each such section unique by adding at the end of it, in parentheses, the name of the original author or publisher of that section if known, or else a unique number. Make the same adjustment to the section titles in the list of Invariant Sections in the license notice of the combined work.
In the combination, you must combine any sections entitled “History” in the various original documents, forming one section entitled “History”; likewise combine any sections entitled “Acknowledgments”, and any sections entitled “Dedications”. You must delete all sections entitled “Endorsements.”
COLLECTIONS OF DOCUMENTS
You may make a collection consisting of the Document and other documents released under this License, and replace the individual copies of this License in the various documents with a single copy that is included in the collection, provided that you follow the rules of this License for verbatim copying of each of the documents in all other respects.
You may extract a single document from such a collection, and distribute it individually under this License, provided you insert a copy of this License into the extracted document, and follow this License in all other respects regarding verbatim copying of that document.
AGGREGATION WITH INDEPENDENT WORKS
A compilation of the Document or its derivatives with other separate and independent documents or works, in or on a volume of a storage or distribution medium, does not as a whole count as a Modified Version of the Document, provided no compilation copyright is claimed for the compilation. Such a compilation is called an “aggregate”, and this License does not apply to the other self-contained works thus compiled with the Document, on account of their being thus compiled, if they are not themselves derivative works of the Document.
If the Cover Text requirement of section 3 is applicable to these copies of the Document, then if the Document is less than one quarter of the entire aggregate, the Document's Cover Texts may be placed on covers that surround only the Document within the aggregate. Otherwise they must appear on covers around the whole aggregate.
TRANSLATION
Translation is considered a kind of modification, so you may distribute translations of the Document under the terms of section 4. Replacing Invariant Sections with translations requires special permission from their copyright holders, but you may include translations of some or all Invariant Sections in addition to the original versions of these Invariant Sections. You may include a translation of this License provided that you also include the original English version of this License. In case of a disagreement between the translation and the original English version of this License, the original English version will prevail.
TERMINATION
You may not copy, modify, sublicense, or distribute the Document except as expressly provided for under this License. Any other attempt to copy, modify, sublicense or distribute the Document is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
FUTURE REVISIONS OF THIS LICENSE
The Free Software Foundation may publish new, revised versions of the GNU Free Documentation License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. See http://www.gnu.org/copyleft/.
Each version of the License is given a distinguishing version number. If the Document specifies that a particular numbered version of this License “or any later version” applies to it, you have the option of following the terms and conditions either of that specified version or of any later version that has been published (not as a draft) by the Free Software Foundation. If the Document does not specify a version number of this License, you may choose any version ever published (not as a draft) by the Free Software Foundation.

END OF TERMS AND CONDITIONS

ADDENDUM: How to use this License for your documents

To use this License in a document you have written, include a copy of the License in the document and put the following copyright and license notices just after the title page:

       Copyright (C)  year  your name.
       Permission is granted to copy, distribute and/or modify this document
       under the terms of the GNU Free Documentation License, Version 1.1
       or any later version published by the Free Software Foundation;
       with the Invariant Sections being list their titles, with the
       Front-Cover Texts being list, and with the Back-Cover Texts being list.
       A copy of the license is included in the section entitled ``GNU
       Free Documentation License''.

If you have no Invariant Sections, write “with no Invariant Sections” instead of saying which ones are invariant. If you have no Front-Cover Texts, write “no Front-Cover Texts” instead of “Front-Cover Texts being list”; likewise for Back-Cover Texts.

If your document contains nontrivial examples of program code, we recommend releasing these examples in parallel under your choice of free software license, such as the GNU General Public License, to permit their use in free software.

Indices

Index of Concepts

apt: Downloading with APT
apt: Repositories for APT
Architectures: Linux Architectures
authors: Authors
binary debs: Removing the Debian DEB
binary debs: Installing the Debian DEB
binary debs: Configuring the Debian DEB
binary debs: Downloading the Debian DEB
binary rpms: Removing the Binary RPM
binary rpms: Installing the Binary RPM
binary rpms: Configuring the Binary RPM
binary rpms: Downloading the Binary RPM
bug reports, automatic generation: Automatic Problem Reports
bug reports, generating: Generating Problem Reports
bug reports, stand along generation: Stand Alone Problem Reports
bugs: Bugs
bugs, history: Historical Defects
bugs, known: Known Defects
bugs, reporting: Problem Reports
building: Building
building, source dscs: Building from the Debian DSC
building, source srpm: Building from the Source RPM
building, tar ball: Building from the Tar Ball
checkout, cvs: Downloading from CVS
compatibility: Compatibility
configuration: Configuration
configure environment variables: Environment Variables
configure options: Configure Options
configuring, binary debs: Configuring the Debian DEB
configuring, binary rpms: Configuring the Binary RPM
configuring, source dscs: Configuring the Debian DSC
configuring, source srpm: Configuring the Source RPM
configuring, tar ball: Configuring the Tar Ball
conformance: Conformance
contributors: Contributors
conventions: Conventions
credits: Acknowledgements
cvs: Downloading from CVS
definitions: Conventions
developing: Development
downloading: Downloading
downloading, apt: Downloading with APT
downloading, binary rpms: Downloading the Binary RPM
downloading, debian debs: Downloading the Debian DEB
downloading, debian dscs: Downloading the Debian DSC
downloading, source srpm: Downloading the Source RPM
downloading, tar ball: Downloading the Tar Ball
downloading, yum: Downloading with YUM
drivers: Drivers
generating bug reports: Stand Alone Problem Reports
generating bug reports: Generating Problem Reports
generating bug reports automatically: Automatic Problem Reports
generating problem reports: Generating Problem Reports
generating problem reports automatically: Automatic Problem Reports
generating problem reports stand alone: Stand Alone Problem Reports
GNU/Linux Distributions: GNU/Linux Distributions
headers: Files
history: History
history bugs: Historical Defects
indices: Indices
installation: Installation
installing: Installing
installing, binary debs: Installing the Debian DEB
installing, binary rpms: Installing the Binary RPM
installing, tar ball: Installing the Tar Ball
introduction: Introduction
iperf-devel-2.0.8-1.7.2.i686.rpm: Configuring the Binary RPM
iperf-doc-2.0.8-1.7.2.i686.rpm: Configuring the Binary RPM
iperf-lib-2.0.8-1.7.2.i686.rpm: Configuring the Binary RPM
iperf-openss7-2.0.8-1.7.2.i686.rpm: Configuring the Binary RPM
iperf-source-2.0.8-1.7.2.i686.rpm: Configuring the Binary RPM
known bugs: Known Defects
known problems: Known Problems
libraries: Libraries
license, AGPL: GNU Affero General Public License
license, FDL: GNU Free Documentation License
license, GNU Affero General Public License: GNU Affero General Public License
license, GNU Free Documentation License: GNU Free Documentation License
license, GNU General Public License: GNU General Public License
license, GPL: GNU General Public License
license, Lesser General Public License: GNU Lesser General Public License
license, LGPL: GNU Lesser General Public License
license, UI: University of Illinois License
license, University of Illinois: University of Illinois License
licenses: Licenses
licensing: Notice
maintainer: Maintainer
manual abstract: Abstract
manual audience: Abstract
manual disclaimer: Disclaimer
manual intent: Abstract
manual notice: Notice
manual objective: Abstract
manual revisions: Revisions
maturity: Maturity
modules: Modules
objective: Objective
organization: Organization
overview: Overview
post-installation checks: Post-installation Checks
pre-installation checks: Pre-installation Checks
prerequisites: Prerequisites
problem reports: Problem Reports
problems, known: Known Problems
quick start guide: Quick Start Guide
reference: Reference
release iperf-2.0.1-1: Release iperf-2.0.1-1
release iperf-2.0.2: Release iperf-2.0.2
release iperf-2.0.3: Release iperf-2.0.3
release iperf-2.0.4: Release iperf-2.0.4
release iperf-2.0.5: Release iperf-2.0.5
release iperf-2.0.5.rc2: Release iperf-2.0.5.rc2
release iperf-2.0.5.rc3: Release iperf-2.0.5.rc3
release iperf-2.0.5rc1: Release iperf-2.0.5rc1
release iperf-2.0.6: Release iperf-2.0.6
release iperf-2.0.7: Release iperf-2.0.7
release iperf-2.0.8: Release iperf-2.0.8
release notes: Release Notes
releases: Releases
removing: Removing
removing, binary debs: Removing the Debian DEB
removing, binary rpms: Removing the Binary RPM
removing, source dscs: Removing the Debian DSC
removing, source srpm: Removing the Source RPM
removing, tar ball: Removing the Tar Ball
reporting bugs: Problem Reports
repositories: Repositories
repositories, apt: Repositories for APT
repositories, yum: Repositories for YUM
schedule: Schedule
source dscs: Removing the Debian DSC
source dscs: Building from the Debian DSC
source dscs: Configuring the Debian DSC
source dscs: Downloading the Debian DSC
source rpms: Removing the Source RPM
source rpms: Building from the Source RPM
source rpms: Configuring the Source RPM
source rpms: Downloading the Source RPM
sponsors: Sponsors
tar ball: Removing the Tar Ball
tar ball: Installing the Tar Ball
tar ball: Building from the Tar Ball
tar ball: Configuring the Tar Ball
tar ball: Downloading the Tar Ball
test suites: Test Suites
test suites, running: Running Test Suites
troubleshooting: Troubleshooting
UI Iperf: UI Iperf
utilities: Utilities
web resources: Web Resources
yum: Downloading with YUM
yum: Repositories for YUM

Index of Functions and Macros

Index of Variables and Constants

BZIP2: Environment Variables
BZIP2_CMD: Environment Variables
DEB_BUILD_ARCH: Environment Variables
DEB_BUILD_GNU_CPU: Environment Variables
DEB_BUILD_GNU_SYSTEM: Environment Variables
DEB_BUILD_GNU_TYPE: Environment Variables
DEB_HOST_ARCH: Environment Variables
DEB_HOST_GNU_CPU: Environment Variables
DEB_HOST_GNU_SYSTEM: Environment Variables
DEB_HOST_GNU_TYPE: Environment Variables
DESTDIR: Environment Variables
DPKG: Environment Variables
DPKG_BUILDPACKAGE: Environment Variables
DPKG_SOURCE: Environment Variables
GNUPGHOME: Environment Variables
GNUPGUSER: Environment Variables
GPG: Environment Variables
GPGPASSWD: Environment Variables
GZIP: Environment Variables
GZIP_CMD: Environment Variables
LDCONFIG: Environment Variables
MAKEWHATIS: Environment Variables
NM: Environment Variables
OBJDUMP: Environment Variables
PIC: Environment Variables
REFER: Environment Variables
RPM: Environment Variables
RPMBUILD: Environment Variables
SOELIM: Environment Variables
TBL: Environment Variables

Index of Files and Programs

Short Contents

OpenSS7 IPERF Utility Installation and Reference Manual
About This Manual
Preface
Quick Start Guide
1 Introduction
2 Objective
3 Reference
4 Conformance
5 Releases
6 Installation
7 Troubleshooting
Licenses
Indices

OpenSS7 IPERF Utility Installation and Reference Manual
About This Manual
Preface
Quick Start Guide
- OpenSS7 IPERF Utility
1 Introduction
2 Objective
3 Reference
4 Conformance
5 Releases
6 Installation
7 Troubleshooting
Licenses
Indices

Footnotes

[1] Formerly X/Open and UNIX International.

[2] See GNU/Linux Distributions, for more information.

[3] If you are using a Debian release, please make sure to install the groff extension package (‘groff_ext’), as it contains the refer or grefer commands necessary for including references in the manual pages.

[4] Please see Problem Reports, or the file PROBLEMS in the release directory for more information on filing a proper Problem Report.

[5] Note that macro and reference databse files are not installed if the package is configured for cooked manpages.

[6] See GNU/Linux Distributions, for more information.

[7] If you are using a Debian release, please make sure to install the groff extension package (‘groff_ext’), as it contains the refer or grefer commands necessary for including references in the manual pages.

[8] Items marked as ‘TBD’ are scheduled to have support deprecated. That is, in a future release, the distributions marked ‘TBD’ will not longer be validated before release.

[9] See sections Disclaimer of Warranty and Limitation of Liability under GNU Affero General Public License.

[10] Note that not all releases have source RPM packages. Release packages that do not contain kernel modules do not generate a source RPM package.

[11] Note that not all release packages contain shared libraries, and, therefore, not all release packages contain this package.

[12] Note that not all releases have source DEB packages. Release packages that do not contain kernel modules do not generate a source DEB package.

[13] Note that not all release packages contain shared libraries, and, therefore, not all release packages contain this package.

[14] Older version of bison (2.0) and the older version of flex (2.5.4a) are also suitable. Where possible, use the more recent bison 2.3 and flex 2.5.33.

[15] A notable exception is Debian and Fedora 7. Note that on Fedora 7 the gettext-devel package must be installed.

[16] In particular, for CentOS, Fedora 6 or 7, the tetex-latex and gnuplot packages must be loaded as well. Note also that the latex2html used to be part of the textex package (or subpackages) but is now often packaged on its own. Recent distributions such as SUSE 11.0 and Fedora 9 use the texlive package instead of the tetex package.

[17] In particular, some Debian systems do not load the groff(1) extensions package and do not have grefer(1) installed. Although this is an oversight on the configuration of the particular Debian system, we accomodate such misconfiguration with this feature.

[18] In particular, some Debian or Ubuntu systems do not load the groff(1) extensions package and do not have grefer(1) installed. Although this is an oversight on the configuration of the particular Debian or Ubuntu system, we accomodate such misconfiguration with this feature.

[19] Because it is a cross-build, the kernel version on the build machine is unlikely to be the kernel version of the target machine, except by coincidence.

[20] /usr/libexec/iperf is just an example, the actual location is ${libexecdir}/${PACKAGE}, which varies from distribution to distribution (as some distributions such as Mandriva do not have a libexec directory).

[21] Therefore, it is possible to download the package, configure it, and then uninstall it. This is handy if you do not have the sources used to build and install the package immediately available.

[22] This is useful from the OpenSS7 Master Package.

[23] Theoretically this is true, however, the OpenSS7 Project does not use any maintainer programs that are not generally available (i.e. open source).

[24] Note that because logging targets invoke a pipe, automake(1) does not return the correct return status (always returns success if the tee(1) operation is successful). Therefore, these targets should not be invoked by scripts that need to use the return value from automake(1).

[25] This particular check has caught some name space pollution that has occurred in the 2.6.11 kernel.

[26] ‘send-pr’ launches the user's EDITOR to edit the problem report before submitting it.

iperf Manual

Description: OpenSS7 Online Manuals

OpenSS7 IPERF Utility

OpenSS7 IPERF Utility Installation and Reference Manual

About This Manual

Preface

Notice

Abstract

Objective

Intent

Audience

Revisions

Version Control

ISO 9000 Compliance

Disclaimer

U.S. Government Restricted Rights

Acknowledgements

Sponsors

Contributors

Authors

Maintainer

Web Resources

Bug Reports

Mailing Lists

Spam

Acceptable Use Policy

Large Attachments

Quick Start Guide

OpenSS7 IPERF Utility

Release

Prerequisites

Installation

Brief Installation Instructions

Detailed Installation Instructions

1 Introduction

1.1 Overview

1.2 Organization of this Manual

1.3 Conventions and Definitions

2 Objective

3 Reference

3.1 Files

3.2 Drivers

3.3 Modules

3.4 Libraries

3.5 Utilities

3.6 Development

4 Conformance

5 Releases

5.1 Prerequisites

5.2 Compatibility

5.2.1 GNU/Linux Distributions

5.2.2 Architectures

5.2.3 UI Iperf

iperf-2.0.8 and Iperf Compatibility

iperf-2.0.8 and Option Compatibility

iperf-2.0.8 and SCTP Compatibility

5.3 Release Notes

Major changes for release iperf-2.0.8

Major changes for release iperf-2.0.7

Major changes for release iperf-2.0.6

Major changes for release iperf-2.0.5

Major changes for release iperf-2.0.5.rc3

Major changes for release iperf-2.0.5.rc2

Major changes for release iperf-2.0.5rc1

Major changes for release iperf-2.0.4

Major changes for release iperf-2.0.3

Initial public release iperf-2.0.2

Initial release iperf-2.0.1-1

5.4 Maturity

5.4.1 Pre-Alpha Releases

5.4.2 Alpha Releases

5.4.3 Beta Releases

5.4.4 Gamma Releases

5.4.5 Production Releases

5.4.6 Unstable Releases

5.5 Bugs

5.5.1 Defect Notices

5.5.2 Known Defects

5.5.3 Defect History

Bugs